2006 LAND ROVER FRELANDER 2 torque

Publi s hed: 11-May-2011
Wipers and Washers -
C apacitiesItemCapacity (liters/pints/US quarts)
Windscreen washer reservoir:
W it h headl amp was h5.8/10.2/6.1W it hout headl amp was h3.1/5.5/3.3
General SpecificationItemSpecification
Front wi per mot orVal eo
Power washer pump makeKaut ex Text ronRain sens orBonded t o i nner s urface of t he wi nds creen behind t he int eri or mirror
Rear wiper mot orVal eo
Torque Specifications
DescriptionNMlb-ftFront wi per arms t o li nkage nut4533
Rear window wi per motor nuts107
Rear wiper arm t o mot or nut75W iper linkage t o body bol ts86
W as her res ervoir and pump as s embly t o body bolt s64
W as her res ervoir and pump as s embly t o bumper armat ure bol ts64W as her res ervoir fil ler neck s upport bolt43
W indshi el d wi per mot or bolt s107

Publi s hed: 11-May-2011
Roof Opening Panel -
Torque SpecificationsDescriptionNmlb-ft
Roof opening panel mot or Torx s crews54
Roof opening panel ali gnment Torx screws32Roof opening panel bolt s32
Roof opening panel mot or t ether44

Publi s hed: 11-May-2011
Bumpers -
ProductPart Number
Rear bumper PDC sens or mount ing adhes ive3M 8005B35
Torque SpecificationsDescriptionNmlb-ft
Front bumper bol ts to body4835
Front bumper cover fi xi ng t o fender bracket43Front bumper cover fi xi ng t o hood lat ch panel32
Front bumper cover fi xi ng t o undertray43
Rear bumper bolt s t o body3022Rear bumper cover fixing behi nd lamp as s embly21
Rear bumper cover s crews21
Rear bumper cover t o bracket bol ts43Fender s plas h s hield screws21

Publi s hed: 11-May-2011
Safety Belt System -
Torque SpecificationsDescriptionNmlb-ft
Adjus t abl e s houl der anchorage Torx bolt s2518
Front s afet y belt buckl e to s eat Torx bol t4030Front s afet y belt lower anchor Torx bol t*4030
Front s afet y belt ret ract or Torx bol t*4030
Front s afet y belt upper anchor Torx bol t*4030Rear cent er s afet y belt buckl e Torx bol t5541
Rear cent er s afet y belt l ower anchor5541
Rear cent er s afet y belt retract or Torx bolt3526Rear safety bel t lower anchor4030
Rear safety bel t upper anchor Torx bolt4030
Rear seat bel t ret ractor4030W ebbing gui de86
* New nuts/bolts must be fitted

Publi s hed: 11-May-2011
Supplemental Restraint System -
Torque SpecificationsDescriptionNmlb-ft
B-pi ll ar si de impact s ens or Torx s crews107
C-pi ll ar si de impact s ens or Torx bolt s107Driver lower air bag module64
Front i mpact s everit y s ensor Torx bol ts107
Pas senger ai r bag module bracket Torx s crews75Pas senger ai r bag module nut s107
Res traints cont rol module (RCM) Torx s crews107
Side ai r bag module nut s107Side ai r curtai n module Torx s crews107

Release the LH and RH suspension arms, as the subframe is lowered,
and tie them aside. 21.
22. NOTE: Do not disassemble further if the component is removed for
access only.
Remove the catalyst support bracket. 22.
Remove the steering gear. 23.
Installation
Install the steering gear.
Torque: 105 Nm1.
Using the special tool, support the subframe. 2.
3.
CAUTION: Install all the bolts finger tight before final tightening.
Raise the front subframe to allow installation of the suspension arms and the bolts. 3.
Install the LH and RH suspension arms as the subframe is raised. 4.
Install the stabilizer bar. 5.
6.
CAUTION: Make sure that new bolts are installed.
Install the subframe cross-brace.
Torque: 45 Nm6.
7.
CAUTION: Make sure that new bolts are installed. 7.

St a g e
1:
St a g e
2:
St a g e 1:
St a g e 2: Install the 2 support brackets.
Torque: 25 Nm
Install the
front
subframe.
Sp e c i a l
T ool (s ):
502-012
Torque:
140 Nm
240°
8.
Install the catalyst support bracket.
Torque: 10 Nm
9.
Install the fuel line. 10.
Install the purge line. 11.

Tighten bolt 1.
Torque:
140 Nm
45°Tighten bolt 2 to
Torque: 175 Nm
Tighten bolt 3 to
Torque: 175 Nm
12.
Secure the catalytic converters. 13.
14.
WARNING: Make sure that new nuts are installed.
Connect the LH and RH tie-rod end ball joints.
Torque: 105 Nm14.
Connect the steering gear pressure lines.
Torque: 25 Nm
15.
16.
WARNING: Make sure that new nuts are installed.
CAUTION: Make sure that the ball joint ball does not rotate.
Install the stabilizer link bar to the lower suspension arm, and tighten to 55 Nm (41
lb.ft) 16.
Secure the electrical harness. 17.

18. WARNING: Make sure that a new steering column flexible coupling bolt is
installed.
Connect the steering column to the steering gear.
Torque: 25 Nm18.
Connect and s ecure t he cat alys t moni t or s ens or el ect ri cal connect ors . 19.
Install the 2 subframe mounting bolts and remove the jack. 20.
Install the engine undershield.
Refer to: Engine Undershield
(501-02 Front End Body Panel s, Removal and
Installation). 21.
Install the wheels and tires.
Refer to: W heel and Tire
(204-04 W heels and Tires , Removal and Ins t all at i on). 22.
Refill and bleed the power steering.
Refer to: Power Steering System Bleeding
(211-00 St eeri ng Sys t em - General
Informat ion, General Procedures). 23.
Using only four wheel alignment equipment approved by Land Rover, check and adjust
the wheel alignment. 24.