2006 LAND ROVER FRELANDER 2 sensor

Publi s hed: 15-Nov-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Driver
Seat Module (DSM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the driver s eat s ys tem, refer t o the relevant Descri pti on and Operat ion s ect ion in t heworks hop manual .For addit ional informat ion, refer t o: Seat s (501-10 Seati ng, Des cript ion and Operat ion).
Driver seat module (DSM).DT CDescriptionPossible CauseAction
B1060-11Seat Headres t Mot orOut put - Ci rcuit s hort t oground
Seat headrest mot orcircui t s hort circuit t oground
Refer to t he elect rical circuit di agrams andcheck seat headres t motor circui t for s hortci rcuit t o ground
B1060-15Seat Headres t Mot orOut put - Ci rcuit s hort t obatt ery or open
Seat headrest mot orcircui t s hort circuit t opower, open circui t
Refer to t he elect rical circuit di agrams andcheck seat headres t motor circui t for s hortci rcuit t o power, open circuit
B1064-31Seat Headres t Mot orSensor - No si gnalSeat headrest mot ors ensor circui t opencircui t, hi gh res is t anceSeat headrest mot ors ensor i nternal fai lure
Refer to t he elect rical circuit di agrams andcheck seat headres t motor s ensor circui t foropen circui t, hi gh res is t anceCheck and ins t al l new s eat headres t mot ors ens or as required. Refer t o t he warrant y poli cyand procedures manual, or determine if anyprior approval programme is i n operati on, priort o t he i ns t allat ion of a new module/component
B106D-24Headres t Up Swit ch -Signal st uck highSeat headrest up swi tchcircui t s hort circuit t opower
Refer to t he elect rical circuit di agrams andcheck seat headres t up s wit ch ci rcuit for shortci rcuit t o power
B106E-24Headres t Down Swit ch -Signal st uck highSeat headrest downs wi tch circui t shortcircui t to power
Refer to t he elect rical circuit di agrams andcheck seat headres t down s wit ch ci rcuit fors hort ci rcuit t o power
B1087-83Lin Bus “A” - Value ofs ignal protecti oncalcul ati on incorrect
Seat and memorys wi tch pack int ernalfailure
Check and ins t al l new s eat and memory s wi tchpack as requi red. Refer to the warrant y policyand procedures manual, or determine if anyprior approval programme is i n operati on, priort o t he i ns t allat ion of a new module/component
B1087-86Lin Bus “A” - Signalinvali dSeat and memorys wi tch pack int ernalfailure
Check and ins t al l new s eat and memory s wi tchpack as requi red. Refer to the warrant y policyand procedures manual, or determine if anyprior approval programme is i n operati on, priort o t he i ns t allat ion of a new module/component
B1087-87Lin Bus “A” - Mi ss i ngmes s ageSeat and memorys wi tch pack ci rcuit opencircui tSeat and memorys wi tch pack int ernalfailure
Refer to t he elect rical circuit di agrams andcheck seat and memory s wit ch pack ci rcuit forcommuni cat ion faul tCheck and ins t al l new s eat and memory s wi tchpack as requi red. Refer to the warrant y policyand procedures manual, or determine if anyprior approval programme is i n operati on, priort o t he i ns t allat ion of a new module/component

Publ is hed: 01-Oct -2011
General Information - Diagnostic Trouble Code (DTC) IndexTD4 2.2L Diesel,
DTC: Engine Control Module (ECM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
For addit ional informat ion on t he des cript ion and operat ion of t he sys t em: For additional informati on, refer t o: Engi ne(303-01B Engi ne - TD4 2.2L Di esel , Descri pti on and Operat ion).
Powertrain control module diesel (PC MD)
DT CDescriptionPossible CauseAction
B10A2-68Cras h Input - Eventinformat ionAi r bag event detectedUsi ng t he manufacturer approveddiagnos t ic s yst em, check rest rai ntscont rol module, for related DTCs andrefer t o t he rel evant DTC i ndex
P0016-00Cranks haft Pos i ti on -Cams haft Posi ti on Correlati on- Bank 1 Sensor A - No s ubt ype i nformati on
Engine t iming i ncorrectTiming chain i nst all edi ncorrect lyThe relati ve posi ti ons oft he crankshaft pos it ions ensor and cam t imingplat e t eet h are not correct
Check engine t imingCheck cams haft s ens or t imi ng plate isins tal led correct lyCheck valve t imingCheck t imi ng chai n i ns t alled correctl y
P0030-12HO2S Heater Control Circuit(Bank 1, Sensor 1) - Ci rcuits hort t o batt ery
• NO TE: - Ci rcuit O_T_SHT1 -
Front heated oxygens ensor heater cont rolcircui t s hort ci rcuit t opowerFront heated oxygens ensor failure
Refer to the el ect ri cal circui t diagramsand check front heat ed oxygen s ensorheat er cont rol ci rcuit for short ci rcuit t opowerCheck and i ns t all a new front heatedoxygen s ens or as requi red. Refer to thewarrant y poli cy and procedures manual,or det ermi ne if any prior approvalprogramme is in operat ion, pri or t o t heins tal lati on of a new modul e/component
P0030-13HO2S Heater Control Circuit(Bank 1, Sensor 1) - Ci rcuitopen
• NO TE: - Ci rcuit O_T_SHT1 -
Front heated oxygens ensor heater cont rolcircui t high resi st ance,open circui tFront heated oxygens ensor failure
Refer to the el ect ri cal circui t diagramsand check t he front heat ed oxygensens or heat er cont rol ci rcuit for highres is t ance, open ci rcuitCheck and i ns t all a new front heatedoxygen s ens or as requi red. Refer to thewarrant y poli cy and procedures manual,or det ermi ne if any prior approvalprogramme is in operat ion, pri or t o t heins tal lati on of a new modul e/component
P0031-11HO2S Heater Control CircuitLow (Bank 1, Sens or 1) -Circui t s hort to ground
• NO TE: - Ci rcuit O_T_SHT1 -
Front heated oxygens ensor heater cont rolcircui t s hort ci rcuit t ogroundFront heated oxygens ensor failure
Refer to the el ect ri cal circui t diagramsand check front heat ed oxygen s ensorheat er cont rol ci rcuit for short ci rcuit t ogroundCheck and i ns t all a new front heatedoxygen s ens or as requi red. Refer to thewarrant y poli cy and procedures manual,or det ermi ne if any prior approvalprogramme is in operat ion, pri or t o t heins tal lati on of a new modul e/component
P0031-16HO2S Heater Control CircuitLow (Bank 1, Sens or 1) -Circui t vol tage belowt hreshol d
• NO TE: - Ci rcuit O_T_SHT1 -
Front heated oxygens ensor heater cont rolcircui t s hort ci rcuit t ogroundFront heated oxygens ensor failure
Refer to the el ect ri cal circui t diagramsand check front heat ed oxygen s ensorheat er cont rol ci rcuit for short ci rcuit t ogroundCheck and i ns t all a new front heatedoxygen s ens or as requi red. Refer to thewarrant y poli cy and procedures manual,or det ermi ne if any prior approvalprogramme is in operat ion, pri or t o t he

DT CDescriptionPossible CauseAction
P0048-00Turbo charger/SuperchargerBoost Cont rol A Ci rcuit High -No s ub t ype informati on
Actuat or power s tage errorRefer to the el ect ri cal circui t diagramsand check connecti ons are s ecure andwiring i ntegri tyCarry out t he pinpoint t est s as s oci at edwit h t his DTC us ing the manufact urerapproved di agnos ti c s ys t em
P0048-12Turbo charger/SuperchargerBoost Cont rol A Ci rcuit High -Circui t s hort to bat t ery
• NO TE: - Ci rcuit O_T_BPAPOS -
Vari able geometryt urbocharger actuat or vanecircui t s hort ci rcuit t opower
Refer to the el ect ri cal circui t diagramsand check t he variable geomet ryturbocharger act uator vane ci rcuit , forshort ci rcuit t o powerCarry out t he pinpoint t est s as s oci at edwit h t his DTC us ing the manufact urerapproved di agnos ti c s ys t em
P0048-15Turbo charger/SuperchargerBoost Cont rol A Ci rcuit High -Circui t s hort to bat t ery oropen
• NO TE: - Ci rcuit O_T_BPANEG -
Vari able geometryt urbocharger actuat or vanecircui t s hort ci rcuit t opower, open circui t
Refer to the el ect ri cal circui t diagramsand check t he variable geomet ryturbocharger act uator vane ci rcuit , forshort ci rcuit t o power, open circui tCarry out t he pinpoint t est s as s oci at edwit h t his DTC us ing the manufact urerapproved di agnos ti c s ys t em
P0053-16HO2S Heater Res is t ance(Bank 1, Sensor 1) - Ci rcuitvolt age bel ow t hres hol d
Front heated oxygens ensor heater cont rolcircui t s hort ci rcuit t ogroundFront heated oxygens ensor failure
Refer to the el ect ri cal circui t diagramsand check front heat ed oxygen s ensorheat er cont rol ci rcuit for short ci rcuit t ogroundCheck and i ns t all a new front heatedoxygen s ens or as requi red. Refer to thewarrant y poli cy and procedures manual,or det ermi ne if any prior approvalprogramme is in operat ion, pri or t o t heins tal lati on of a new modul e/component
P0053-17HO2S Heater Res is t ance(Bank 1, Sensor 1) - Ci rcuitvolt age above t hres hol d
Front heated oxygens ensor heater cont rolcircui t s hort ci rcuit t opowerFront heated oxygens ensor failure
Refer to the el ect ri cal circui t diagramsand check front heat ed oxygen s ensorheat er cont rol ci rcuit for short ci rcuit t opowerCheck and i ns t all a new front heatedoxygen s ens or as requi red. Refer to thewarrant y poli cy and procedures manual,or det ermi ne if any prior approvalprogramme is in operat ion, pri or t o t heins tal lati on of a new modul e/component
P0053-1AHO2S Heater Res is t ance(Bank 1, Sensor 1) - Ci rcuitres is t ance bel ow t hreshol d
Front heated oxygens ensor heater cont rolcircui t s hort ci rcuit t ogroundFront heated oxygens ensor failure
Refer to the el ect ri cal circui t diagramsand check front heat ed oxygen s ensorheat er cont rol ci rcuit for short ci rcuit t ogroundCheck and i ns t all a new front heatedoxygen s ens or as requi red. Refer to thewarrant y poli cy and procedures manual,or det ermi ne if any prior approvalprogramme is in operat ion, pri or t o t heins tal lati on of a new modul e/component
P0053-1BHO2S Heater Res is t ance(Bank 1, Sensor 1) - Ci rcuitres is t ance above t hres hol d
Front heated oxygens ensor heater cont rolcircui t s hort ci rcuit t opowerFront heated oxygens ensor failure
Refer to the el ect ri cal circui t diagramsand check front heat ed oxygen s ensorheat er cont rol ci rcuit for short ci rcuit t opowerCheck and i ns t all a new front heatedoxygen s ens or as requi red. Refer to thewarrant y poli cy and procedures manual,or det ermi ne if any prior approvalprogramme is in operat ion, pri or t o t heins tal lati on of a new modul e/component
P0069-00MAP - Barometric Pres s ureCorrelati on - No s ub t ypeinformat ion
Manifold abs olut epres s ure/boos t pres s ures ensor circui t s hort ci rcuitt o ground, s hort ci rcuit t opower, open circui t, highresi st anceManifold abs olut epres s ure/boos t pres s ures ensor i nt ernal faul tBaromet ri c pres s ure s ens orfailure (internal enginecontrol modul e fault )
Usi ng t he manufacturer approveddiagnos t ic s yst em perform t he (T urbo,exhaust gas recirculation and air pathdynamic test) rout ineRefer to the el ect ri cal circui t diagramsand check t he boos t pres s ure s ens orci rcuit - I_A_BPS - For s hort circui t toground, s hort circui t t o power, openci rcuit , high resi st ance

Publi s hed: 04-May-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Headlamp
Control Module (HCM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
For addit ional informat ion, refer t o: Ext eri or Li ght ing (417-01 Ext erior Light ing, Descri pti on and Operat ion).
Adaptive Front Lighting System (AFS) C ontrol Module
DT CDescriptionPossible CauseActionB1041-04Level ing Control -Syst em InternalFailures
Module internal failureSus pect Adapt ive Front Light ing Syst em (AFS) Cont rolModul e i nt ernal fault . Replace as required, refer t o t he newmodule/component i nst all at ion not e at t he top of t he DTCIndexB1041-54Level ing Control -Mis s ing Cal ibrat ion• NO TE: This DTC wil l normall ybe l ogged when a new modulehas been ins t al led.
Level ing s ens orcali brati on rout ine notcarried out
• NOTE: Sens or cal ibrat ion routi ne mus t be carried out wit hthe vehicle unl aden.
Calibrate t he Headlamp Leveli ng sens ors us ing themanufacturer approved diagnost ic sys tem, carry t he outrout ine 'Headlamp Cont rol Module Sys tem Cali brati on' fromthe 'Modul e programming and confi gurati on - Setup andConfigurat ion - Li ght ing'B1087-83LIN Bus "A" - Val ueof s ignal protecti oncal cul ati on incorrect
LIN Bus circui t faultNo communi cat ion ont he LIN BusLIN bus EMCi nt erference
• NOTE: This circui t uses s hiel ded cable
Refer to the el ect ri cal circui t diagrams and check the LINBus ci rcuit for harness damage
B1087-86LIN Bus "A" - Si gnalInvali dLIN Bus circui t faultNo communi cat ion ont he LIN BusLIN bus EMCi nt erference
• NOTE: This circui t uses s hiel ded cable
Refer to the el ect ri cal circui t diagrams and check the LINBus ci rcuit for harness damage
B1087-88LIN Bus "A" - BusOffLIN Bus circui t faultNo communi cat ion ont he LIN Bus
• NOTE: This circui t uses s hiel ded cable
Refer to the el ect ri cal circui t diagrams and check the LINBus ci rcuit for harness damageB10AE-11Headl amp Level ingMotor - Ci rcuit s hortt o ground
Headlamp Leveli ngMot or control ci rcuits hort t o ground
Refer to the el ect ri cal circui t diagrams and check Headl ampLeveli ng Motor control ci rcuit for s hort t o ground
B10AE-12Headl amp Level ingMotor - Ci rcuit s hortt o batt ery
Headlamp Leveli ngMot or control ci rcuits hort t o power
Refer to the el ect ri cal circui t diagrams and check Headl ampLeveli ng Motor control ci rcuit for s hort t o power
B10AE-64Headl amp Level ingMotor - Si gnalplaus ibil it y fai lure
Signal plaus ibil it y fai lure(vol tage out of range)Refer to the el ect ri cal circui t diagrams and check Headl ampLeveli ng Motor circui ts for fai lure. Di sconnect one headlampconnect or, clear DTC and re-t est . If DTC cleared, s us pectAdapt ive Front Light ing Sys tem (AFS) Control Module orci rcuit s t o t he dis connect ed s ide of t he fai lure. If DTCremai ns , reconnect first headlamp and dis connect s econd,cl ear DTC and re-tes t. If DTC cleared, s us pect Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e or circui ts t othe di s connect ed s ide of t he fai lure. If DTC remai ns,s us pect common ci rcuit s of the fail ure. Refer t o t heelectrical ci rcuit diagrams and check as requi red
B1A59-11Sens or 5 Vol t Supply- Circui t s hort toground
Headlamp Leveli ngSensor 5 vol t supplycircui t s hort to ground
Refer to electrical ci rcuit diagrams and check HeadlampLeveli ng Sens or 5 volt s upply circui t for s hort t o ground
B1A59-12Sens or 5 Vol t Supply- General ElectricalFailure
Headlamp Leveli ngSensor 5 vol t supplycircui t s hort to power
Refer to electrical ci rcuit diagrams and check HeadlampLeveli ng Sens or 5 volt s upply circui t for s hort t o power

DT CDescriptionPossible CauseAction
B1D64-01Left HeadlampSwivell ing Mot or -General Elect ricalFailure
Internal Headlamp Mot orFaultInternal HeadlampCi rcuit Faul t
Us ing t he manufacturer approved diagnost ic sys temperform an On Demand Self Tes t, l ook for any errors i nmovement (compare wi th other headl amp) and vi sual lyins pect t he lamp for i nt ernal damage or di s locat ion (balljoi nt s out). Refer t o t he electrical ci rcuit diagrams andcheck for circui t faul t bet ween t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e and t he Headl amp Swi vel lingMotor. If no mechanical or circui t fault s are evident ,s us pect headlamp int ernal fault , replace as requi red. Referto the new modul e/component i nst all at ion not e at t he topof the DTC Index
B1D64-87Left HeadlampSwivell ing Mot or -Mis s ing mess age
Mi ss i ng mes sageUs ing t he manufacturer approved diagnost ic sys temperform an On Demand Self Tes t, l ook for any errors i nmovement (compare wi th other headl amp) and vi sual lyins pect t he lamp for i nt ernal damage or di s locat ion (balljoi nt s out). Refer t o t he electrical ci rcuit diagrams andcheck for circui t faul t bet ween t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e and t he Headl amp Swi vel lingMotor. If no mechanical or circui t fault s are evident ,s us pect headlamp int ernal fault , replace as requi red. Referto the new modul e/component i nst all at ion not e at t he topof the DTC IndexB1D65-01Right HeadlampSwivell ing Mot or -General elect ricalfai lure
Internal Headlamp Mot orFaultInternal HeadlampCi rcuit Faul t
Us ing t he manufacturer approved diagnost ic sys temperform an On Demand Self Tes t, l ook for any errors i nmovement (compare wi th other headl amp) and vi sual lyins pect t he lamp for i nt ernal damage or di s locat ion (balljoi nt s out). Refer t o t he electrical ci rcuit diagrams andcheck for circui t faul t bet ween t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e and t he Headl amp Swi vel lingMotor. If no mechanical or circui t fault s are evident ,s us pect headlamp int ernal fault , replace as requi red. Referto the new modul e/component i nst all at ion not e at t he topof the DTC Index
B1D65-87Right HeadlampSwivell ing Mot or -Mis s ing mess age
Mi ss i ng mes sageUs ing t he manufacturer approved diagnost ic sys temperform an On Demand Self Tes t, l ook for any errors i nmovement (compare wi th other headl amp) and vi sual lyins pect t he lamp for i nt ernal damage or di s locat ion (balljoi nt s out). Refer t o t he electrical ci rcuit diagrams andcheck for circui t faul t bet ween t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e and t he Headl amp Swi vel lingMotor. If no mechanical or circui t fault s are evident ,s us pect headlamp int ernal fault , replace as requi red. Referto the new modul e/component i nst all at ion not e at t he topof the DTC Index
B1D68-00Left HeadlampSwivell ing FeedbackSens or - No s ub t ypeinformat ion
Internal HeadlampSensor FaultInternal HeadlampCi rcuit Faul t
Us ing t he manufacturer approved diagnost ic sys temperform an On Demand Self Tes t, l ook for any errors i nmovement (compare wi th other headl amp) and vi sual lyins pect t he lamp for i nt ernal damage or di s locat ion (balljoi nt s out). Refer t o t he electrical ci rcuit diagrams andcheck for circui t faul t bet ween t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e and t he Headl amp Swi vel lingFeedback Sens or. If no mechani cal or circuit fault s areevi dent , s us pect headlamp int ernal fault , replace asrequired. Refer t o t he new modul e/component ins t al lat ionnot e at t he t op of the DTC IndexB1D69-00Right HeadlampSwivell ing FeedbackSens or - No s ub t ypeinformat ion
Internal HeadlampSensor FaultInternal HeadlampCi rcuit Faul t
Us ing t he manufacturer approved diagnost ic sys temperform an On Demand Self Tes t, l ook for any errors i nmovement (compare wi th other headl amp) and vi sual lyins pect t he lamp for i nt ernal damage or di s locat ion (balljoi nt s out). Refer t o t he electrical ci rcuit diagrams andcheck for circui t faul t bet ween t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e and t he Headl amp Swi vel lingFeedback Sens or. If no mechani cal or circuit fault s areevi dent , s us pect headlamp int ernal fault , replace asrequired. Refer t o t he new modul e/component ins t al lat ionnot e at t he t op of the DTC Index
C1A03-12Left Front HeightSens or - Circui ts hort t o batt ery
Left Front Hei ght Sens orcircui t s hort to powerRefer to the el ect ri cal circui t diagrams , and check LeftFront Height Sens or circuit for s hort to power
C1A03-14Left Front HeightSens or - Circui ts hort t o ground oropen
Left Front Hei ght Sens orcircui t s hort to ground oropen circui t
Refer to the el ect ri cal circui t diagrams , and check LeftFront Height Sens or circuit for s hort to ground or openci rcuit
C1A05-12Left Rear HeightSens or - Circui ts hort t o batt ery
Left Rear Height Sens orcircui t s hort to powerRefer to the el ect ri cal circui t diagrams , and check Left RearHeight Sens or circuit for s hort to power
C1A05-14Left Rear HeightSens or - Circui ts hort t o ground oropen
Left Rear Height Sens orcircui t s hort to ground oropen circui t
Refer to the el ect ri cal circui t diagrams , and check Left RearHeight Sens or circuit for s hort to ground or open ci rcuit
U0001-88High Speed CANCommunicati on Bus- Bus off
CAN Bus OffCAN Bus Ci rcuit faultCheck ot her modul es for rel ated DTCs . Carry out the CANNetwork Int egrit y t est us i ng the manufact urer approveddiagnos t ic s ys tem

DT CDescriptionPossible CauseAction
U0101-00Lost communicat ionwit h TCM - No s ubt ype i nformati on
Los t communi cat ion wi tht he Trans mis s ionControl Modul eCAN net work fault
Check t he Trans mis s ion Cont rol Module for st ored DTCs .Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Trans mis s ion Cont rol Modul eU0121-00Lost communicat ionwit h Ant i-lock BrakeSyst em (ABS)Control Module - Nos ub type i nformati on
Los t communi cat ion wi tht he Anti -l ock BrakeSys tem Modul eCAN net work fault
Check t he Anti -l ock Brake Sys t em Module for s tored DTCs.Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Anti -l ock Brake Sys t em ModuleU0126-00Lost communicat ionwit h St eering Angl eSens or Module - Nos ub type i nformati on
Los t communi cat ion wi tht he Steering AngleSensor ModuleCAN net work fault
Check t he Steering Angle Sens or Modul e for s t ored DTCs .Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Steeri ng Angle Sens or Module
U0140-00Lost communicat ionwit h Body ControlModule - No subt ype i nformati on
Los t communi cat ion wi tht he Central Junct ion BoxCAN net work fault
Check t he Central Junct ion Box for s tored DTCs . Us ing themanufacturer approved diagnost ic sys tem, complet e t heCAN Net work Integri ty tes t. Refer t o t he electrical ci rcuitdiagrams and check the CAN network bet ween t he Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e and t he CentralJuncti on Box
U0300-00Int ernal Cont rolModule Soft wareIncompati bili ty - Nos ub type i nformati on
Car Configurat ion Fi le(CCF) i nformati oni ncompati ble t o t heAdapti ve Front Li ghti ngSys tem (AFS) Cont rolModule
• NOTE: The Car Configurat ion Fil e (CCF) parametersrequired are (Vehicle type)(Headl amp t ype)(Gearbox t ype)and (Dayrunning light )
Re-configure the Car Confi gurati on Fil e (CCF) as requi redusi ng t he manufact urer approved diagnost ic s ys tem. Cl earDTC and re-t es t . If t he DTC remains s us pect t he Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e, refer t o t henew module ins tall ati on not e at t he t op of the DTC IndexU0402-00Invali d Dat aRecei ved FromTrans mis s ion Cont rolModule - No subt ype i nformati on
Inval id Dat a Recei vedfrom the Transmis si onControl Modul eTrans mi ss i on componentfaul t
Check t he Trans mis s ion Cont rol Module for st ored DTCs .Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Trans mis s ion Cont rol Modul eU0415-00Invali d Dat aRecei ved FromAnti -Lock BrakeSyst em (ABS)Control Module - Nos ub type i nformati on
Inval id dat a receivedfrom Anti -l ock BrakeSys tem Modul eAnt i-lock Brake Syst emModule component fault
Check t he Anti -l ock Brake Sys t em Module for s tored DTCs.Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Anti -l ock Brake Sys t em Module
U0422-00Invali d data fromBody Cont rol Module- No s ub t ypeinformat ion
Inval id s i gnal from theCentral Juncti on BoxCentral Juncti on Boxfaul t
Check t he Central Junct ion Box for s tored DTCs . Us ing themanufacturer approved diagnost ic sys tem, complet e t heCAN Net work Integri ty tes t. Refer t o t he electrical ci rcuitdiagrams and check the CAN network bet ween t he Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e and t he CentralJuncti on Box
U0428-00Invali d Dat aRecei ved FromSteering AngleSens or Module - Nos ub type i nformati on
Inval id Dat a Recei vedfrom the St eeri ng Angl eSensor ModuleSt eering Angle Sens orModule fault
Check t he Steering Angle Sens or Modul e for s t ored DTCs .Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Steeri ng Angle Sens or
U2100-00Ini ti al Configurat ionNot Complet e - Nos ub type i nformati on
Car Configurat ion Fi le(CCF) i nformati on notreceived complet ely
• NOTE: The Car Configurat ion Fil e (CCF) parametersrequired are (Vehicle type)(Headl amp t ype)(Gearbox t ype)and (Dayrunning light )
Re-configure the Car Confi gurati on Fil e (CCF) as requi redusi ng t he manufact urer approved diagnost ic s ys tem. Cl earDTC and re-t es t . If t he DTC remains s us pect t he Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e, refer t o t henew module ins tall ati on not e at t he t op of the DTC IndexU2101-00Control ModuleConfigurat ionIncompati ble - Nos ub type i nformati on
Car Configurat ion Fi le(CCF) i nformati oni ncompati ble t oAdapti ve Front Li ghti ngSys tem (AFS) Cont rolModule
Check t he correct Adapti ve Front Li ght ing Sys t em (AFS)Cont rol Module is i ns t alled to vehicle s pecificati on. Refitori gi nal or repl ace the modul e as required. Refer to thenew module/component ins tall ati on note at t he t op of theDTC Index
U3003-16Batt ery Vol tage -Circui t vol tage belowt hreshol d
The power s upply to theModule has been below9 Vol ts for more than1000 mi ll is econds
Sus pect Bat t ery or Charging fault . Check t he batt erycondit ion and st ate of charge. Check t he vehicle chargi ngs ys t em. Refer to the relevant workshop manual s ect ion.Clear the DTC, cycl e i gni ti on s tat e to off t hen on, i f DTCret urns refer to the el ect ri cal circui t diagrams and checkpower and ground ci rcuit t o t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e

DT CDescriptionPossible CauseAction
B11AE-11Menu butt onMenu but ton ci rcuit - s hort t ogroundRefer to electrical ci rcuit diagrams and checkmenu butt on circui t for s hort t o ground
B11AF-11Phone but t onPhone butt on circui t - s hort togroundRefer to electrical ci rcuit diagrams and checkphone but ton ci rcuit for s hort t o ground
B11B0-11Scan but t onScan butt on circui t - s hort togroundRefer to electrical ci rcuit diagrams and check s canbut t on ci rcuit for short to ground
B11B1-11Auto but t onAut o butt on circui t - s hort togroundRefer to electrical ci rcuit diagrams and check autobut t on ci rcuit for short to ground
B11B3-11Butt on 6But ton 6 circuit - short togroundRefer to electrical ci rcuit diagrams and checkbut t on 6 circui t for s hort t o ground
B11B4-11Butt on 7But ton 7 circuit - short togroundRefer to electrical ci rcuit diagrams and checkbut t on 7 circui t for s hort t o ground
B11B5-11Butt on 8But ton 8 circuit - short togroundRefer to electrical ci rcuit diagrams and checkbut t on 8 circui t for s hort t o ground
B11B6-11Butt on 9But ton 9 circuit - short togroundRefer to electrical ci rcuit diagrams and checkbut t on 9 circui t for s hort t o ground
B1A59-49Sensor 5 volt supplyInternal el ect ronic fail ureIns t al l a new i nformat ion and ent ert ainmentmodule, refer t o t he new modul e/componentins tal lati on note at the t op of the DTC Index
B1D21-15Remote cont rol s wit chRemot e control s wi tch circui t -s hort t o power, open circui tRefer to electrical ci rcuit diagrams and checkremot e cont rol s wi tch circui t for s hort t o power,open ci rcuitU0010-00Medium s peed CANcommunicati on BusBus O ffCarry out pi npoi nt tes ts as s oci ated wit h thi s DTCusi ng t he manufact urer approved diagnost ics ys t em
U0127-00Lost communi cat ionswi th t ire pres s uremonit or s ys t em module
Los t communicat ionsCarry out CAN Network int egrit y t est s us ingmanufacturer approved diagnost ic sys tem. CheckCJB for DTCs and refer to relevant DTC Index.For addit ional informati on, refer t o:Communicati ons Net work (418-00 ModuleCommunicati ons Net work, Di agnos is andTes t ing).
U0140-00Lost communi cat ionswi th CJBLos t communicat ionsCarry out CAN Network int egrit y t est s us ingmanufacturer approved diagnost ic sys tem. CheckCJB for DTCs and refer to relevant DTC Index.For addit ional informati on, refer t o:Communicati ons Net work (418-00 ModuleCommunicati ons Net work, Di agnos is andTes t ing).U0142-00Lost communi cat ionwi th body controlmodule 'B'
Los t communicat ionsCarry out CAN Network int egrit y t est s us ingmanufacturer approved diagnost ic sys tem. CheckCJB for DTCs and refer to relevant DTC Index.For addit ional informati on, refer t o:Communicati ons Net work (418-00 ModuleCommunicati ons Net work, Di agnos is andTes t ing).
U0155-00Lost communi cat ionwi th i nst rument clus t erLos t communicat ionsCarry out CAN Network int egrit y t est s us ingmanufacturer approved diagnost ic sys tem. Checkins trument cl ust er for DTCs and refer to relevantDTC Index.For addit ional informati on, refer t o: Ins trumentClus ter (413-01 Ins t rument Clus t er, Diagnosi sand Tes t ing).
U0159-00Lost communi cat ionswi th park ass i st controlmodule 'A'
Los t communicat ionsCarry out CAN Network int egrit y t est s us ingmanufacturer approved diagnost ic sys tem. Checkparking ai d module for DTCs and refer t o relevantDTC Index.For addit ional informati on, refer t o: Parking Ai d(413-13 Parking Aid, Di agnos is and Tes ti ng).
U0164-00Lost communi cat ionwi th cl imat e cont rolmodule
Los t communicat ionsCarry out CAN Network int egrit y t est s us ingmanufacturer approved diagnost ic sys tem. Checkcl imat e control modul e for DTCs and refer t orel evant DTC Index.For addit ional informati on, refer t o: ClimateCont rol Sys tem (412-00 Cl imat e Control Sys t em -General Informati on, Diagnos is and Tes t ing).
U0184-00Lost communi cat ionwi th radioLos t communicat ionsCarry out pi npoi nt tes ts as s oci ated wit h thi s DTCusi ng t he manufact urer approved diagnost ics ys t emU0186-00Lost communi cat ionswi th audio amplifier 'A'Los t communicat ionsCarry out pi npoi nt tes ts as s oci ated wit h thi s DTCusi ng t he manufact urer approved diagnost ics ys t em

Publ is hed: 27-Apr-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Rear
Differential Control Module (RDCM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the rear different ial sys t em, refer t o t he rel evant Des cript ion and Operat ion s ecti on in theworks hop manual .For addit ional informat ion, refer t o: Rear Drive Axl e and Different ial (205-02 Rear Drive Axl e/Different ial , Des cri pti on andOperat ion).
DT CDescriptionPossible CauseActionP0560-17Syst em Vol tage - circui tvolt age above t hres hol dDi fferenti al El ect ronicModule (DEM) s uppl ycircui t vol tage abovet hres hol d
Check vehi cl e batt ery and chargi ng s ys t em,repai r as required. Refer to the relevants ecti on in the workshop manual. Refer t o t heel ect ri cal circui t diagrams and check thepower and ground s uppl y circui ts t o t heDi fferenti al El ect roni c Modul e (DEM). Cleart he DTC and re-t es t.
P0602-54Powert rain Cont rol ModuleProgramming Error - mi s si ngcal ibrat ion
Di fferenti al El ect ronicModule (DEM)programming errorDi fferenti al El ect ronicModule (DEM) i nt ernalfailure
Us i ng the manufact urer approved diagnos t ics ys tem check and i ns t all lat est l evel ofs oftware to the Different ial Elect roni c Modul e(DEM). Cl ear the DTC and re-t es t.Check and ins t al l a new Di fferenti alEl ect ronic Modul e (DEM) as required. Refer t ot he W arrant y Policy and Procedures manual,or det ermi ne if any pri or approval programmei s i n operati on, prior t o the ins tall ati on of anew modul e/component .
P0607-49Control Module Performance- int ernal electroni c fai lureDi fferenti al El ect ronicModule (DEM) i nt ernalfailure
Cl ear t he DTC and re-t es t. Check and ins talla new Different ial Elect ronic Module (DEM) asrequi red. Refer t o t he W arranty Pol icy andProcedures manual, or determine if any pri orapproval programme is in operat ion, pri or t ot he i ns t allat ion of a new module/component .
P0666-11PCM / ECM / TCM InternalTemperature Sensor Ci rcuit -circuit short to ground
Di fferenti al El ect ronicModule (DEM) i nt ernalfailure
Cl ear t he DTC and re-t es t. Check and ins talla new Different ial Elect ronic Module (DEM) asrequi red. Refer t o t he W arranty Pol icy andProcedures manual, or determine if any pri orapproval programme is in operat ion, pri or t ot he i ns t allat ion of a new module/component .
P0666-15PCM / ECM / TCM InternalTemperature Sensor Ci rcuit -circuit short to bat tery oropen
Di fferenti al El ect ronicModule (DEM) i nt ernalfailure
Cl ear t he DTC and re-t es t. Check and ins talla new Different ial Elect ronic Module (DEM) asrequi red. Refer t o t he W arranty Pol icy andProcedures manual, or determine if any pri orapproval programme is in operat ion, pri or t ot he i ns t allat ion of a new module/component .
P0667-27PCM / ECM / TCM InternalTemperature SensorRange/Performance - s ignalrat e of change abovet hreshol d - s ignal rate ofchange above threshold
Di fferenti al El ect ronicModule (DEM) i nt ernalfailure
Cl ear t he DTC and re-t es t. Check and ins talla new Different ial Elect ronic Module (DEM) asrequi red. Refer t o t he W arranty Pol icy andProcedures manual, or determine if any pri orapproval programme is in operat ion, pri or t ot he i ns t allat ion of a new module/component .
P0748-14Pres s ure Control Sol enoi d AElectrical - ci rcuit s hort t oground or open
Di fferenti al El ect ronicModule (DEM) i nt ernalfailure
Cl ear t he DTC and re-t es t. Check and ins talla new Different ial Elect ronic Module (DEM) asrequi red. Refer t o t he W arranty Pol icy andProcedures manual, or determine if any pri orapproval programme is in operat ion, pri or t o