2006 ACURA CSX oil


(#'
 )
Driver’s Seat
20-122 Seats
Front Seat Frame Replacement (cont’d)
A
B
C
D
Fastener Locations
:Clip,3
A
E
Check the operation of the driver’s seat position sensor
after any of these actions (see page 24-29):
 Driver’s seat position sensor replacement
 Cover plate (front side of driver’s seat slide rail) replacement
NOTE:  Put on gloves to protect your hands.
 Apply oil to the pivot portions of the slide lock.
 Apply multipurpose grease to the sliding portions and pivot portions of the seat tracks.
 If the side airbag has deployed, replace the seat frame and related pieces with new ones (see page
24-185).
1. Remove the front seat (see page 20-118).
2. Remove these items:  Front seat-back cover/pad (see page 20-123)
 Front seat cushion cover/pad (see page 20-127)
 Driver’s seat position sensor (see page 24-211)
 Front seat belt buckle (see page 24-6) 3. Remove the clips, then remove the recline inner
covers (A), the outer upper rail cover (B), the inner
upper rail cover (C) and the module holder (D) from
the seat frame (E).
4. Install the new seat frame in the reverse order of removal, and note these items:
 Make sure the driver’s seat position sensor connector is plugged in properly.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips into place securely.
 Make sure the seat wiring harnesses are routed properly and not pinched.
08/08/21 15:03:56 61SNR030_200_0124
ProCarManuals.com
DYNOMITE -2009-



(#'
 )

S

pecial Tools Required
Passenger’s seat
Driver’s seat
20-123
Front Seat-back Cover Replacement
A
DC
C
C
F
H I
J D
E
A
B
D
E
C
C
C
F
D
G H I
J E
H
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S
RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
 Check the operation of the driver’s seat position sensor after any of these actions (see page 24-29):
– Driver’s seat position sensor replacement
– Cover plate (front side of driver’s seat slide rail) replacement
 Calibrate the ODS unit after any of these actions (see page 24-27):
– Front passenger’s seat replacement (including any seat components)
– Replacement of the front seat weight sensors
– After a vehicle collision
NOTE:  Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to tear or damage the seat covers.
 On the passenger’s seat, do not touch the OPDS sensor in the seat-back pad, and keep it away from oil.
Oil can corrode the sensor caution it to fail.
 Put on gloves to protect your hands.
1. Remove the front seat (see page 20-118).
2. Remove the head restraint. 3

. From under the seat cushion, detach the side
airbag connector clip (A). On the driver’s seat,
disconnect the seat-back heater connector (B).
4. Release the hooks (C) from the seat cushion frame spring (D). Remove the wire ties (E), and pull the
side airbag harness (F) and the seat-back heater
harness (G) (driver’s seat) out through the slits (H)
in the seat cushion cover (I). Turn over the seat
cushion cover, and release the hooks (J).
(cont’d)
08/08/21 15:03:56 61SNR030_200_0125
ProCarManuals.com
DYNOMITE -2009-


(#'
 ) 
(#'


 )
20-16820-168 Exterior Trim
Side Sill Protection Tape
Replacement
Rear License Trim Replacement
AB
C
D
E F
A
D Fastener Locations
: Clip, 4
A : Clip, 2 B
A BC
D
B AA
A
1. Slowly peel up the old side sill protection tape.
2. Clean the body bonding surface with a shop towel
dampened in isopropyl alcohol. After cleaning,
keep oil, grease, and water from getting on the
surface.
3. Peel the adhesive backing from the side sill protection tape.
4. Align the alignment marks (A) of the side sill protection tape (B) with the body line (C), and align
the alignment marks (D) of the application tape (E)
with the round body bulge (F), then press the side
sill protection tape into place. 1. Detach the clips (A, B), and on both sides of the rear
license trim (C), release the edge of the trim from
the inner taillight (D), then remove the trim. Take
care not to scratch the trunk lid.
2. Install the trim in the reverse order of removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips into place securely.
08/08/21 15:05:04 61SNR030_200_0170
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
For Some Models
20-169
Trunk Lid Spoiler Replacement
:Nut,2 :Bolt,2
Fastener Locations
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft) B
C
B A
NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the trunk lid.
1. Open the trunk lid, and remove the nut and bolts from inside the trunk lid. 2. Close the trunk lid. While lifting the trunk lid spoiler
(A) up, disconnect the high mount brake light
terminals (B) from the spoiler subharness (C), then
remove the spoiler.
3. Install the spoiler in the reverse order of removal, and make sure the high mount brake light terminals
are plugged in properly.
08/08/21 15:05:05 61SNR030_200_0171
ProCarManuals.com
DYNOMITE -2009-


(#'


 )
20-170Exterior Trim
Emblem/Sticker Replacement
FRONT ’’A’’ EMBLEM
REAR ’’A’’ EMBLEM
CSX EMBLEM
FRONT GRILLE BASE REAR ’’A’’ EMBLEM
ADHESIVE
TAPE
TRUNK LIDCLIP
CSX EMBLEM
Edge of the trunk lid
20 (0.79) ACURA EMBLEM
SCREWS
33
(1.3) 24
(0.94)
55
(2.17)
Edge of the inner taillight
Edge of the trunk lid
ACURA EMBLEM TYPE-S EMBLEM
(For some models)
Unit: mm (in.)
Adhesive tape: Thickness 0.8 mm (0.03 in.)
FRONT ’’A’’ EMBLEM
Edge of the trunk lidEdge of the inner taillight
104.5
(4.12)
21 (0.83)
17 (0.67)
22 (0.87)
CSX EMBLEM
TYPE-S EMBLEM
(For some models)
NOTE: When removing the emblems, take care not to scratch the body.1. To remove the front ‘‘A’’ emblem, remove the front grille (see page 20-160).
2. Clean the body surface with a shop towel dampened in isopropyl alcohol. After cleaning, keep oil, grease, and water from getting on the surface.
3. Apply the emblem where shown.
4. After installing the front ‘‘A’’ emblem, reinstall the front grille.
08/08/21 15:05:05 61SNR030_200_0172
ProCarManuals.com
DYNOMITE -2009-

(#'

/)
HVAC (Heating, Ventilation, andAir Conditioning)
Climate Control
HVAC (Heating, Ventilation, and Air Conditioning)
...........................
...........................
Special Tools . 21-2
...
..........
...........
........................ ............
.......................... ...
..................................... ................
....................... .............
..................
..................
.................. ......
..................
..................
....................................... ........................
.......................... ...........
..............
........................
.......................... ...
..........
...........
........................ ............
.......................... ...
..................................... ................
....................... .............
..................
..................
.................. ......
..................
..................
....................................... ........................
.......................... ...........
..............
........................
..........................
Component Location Index . 21-3
A/C Service
Tips and Precautions . 21-6
A/C System Inspection . 21-6
A/C Refrigerant Oil Replacement . 21-7
A/C Line Replacement . 21-8
General Troubleshooting Information . 21-9
DTC Troubleshooting Index . 21-15
Symptom Troubleshooting Index . 21-16
System Description . 21-19
Circuit Diagram . 21-26
DTC Troubleshooting . 21-28
Climate Control Power and Ground Circuit
Troubleshooting . 21-53
Navigation Communication Line Circuit
Troubleshooting . 21-54
Radiator and A/C Condenser Fan Low Speed Circuit
Troubleshooting . 21-56
A/C Condenser Fan High Speed Circuit Troubleshooting . 21-60
A/C Compressor Clutch Circuit Troubleshooting . 21-62
A/C Signal Circuit Troubleshooting . 21-64
In-car Temperature Sensor Test . 21-67
In-car Temperature Sensor Replacement . 21-67
Outside Air Temperature Sensor Test . 21-68
Outside Air Temperature Sensor Replacement . 21-68
Sunlight Sensor Test . 21-69
Sunlight Sensor Replacement . 21-69
Evaporator Temperature Sensor Test . 21-70 ............
....
........................ .......
........................
....................................... ...................................
........................ ...........
........................
........................
........................
........................
........................
.................................... ..............................
........................
........................
........................
........................ ..............
.................
.................... ...................
...................... ............
....
........................ .......
........................
....................................... ...................................
........................ ...........
........................
........................
........................
........................
........................
.................................... ..............................
........................
........................
........................
........................ ..............
.................
.................... ...................
......................
Power Transistor Test . 21-71
Air Mix Control Motor Test . 21-72
Air Mix Control Motor
Replacement . 21-72
Mode Control Motor Test . 21-73
Mode Control Motor Replacement . 21-73
Recirculation Control Motor Test . 21-74
Recirculation Control Motor Replacement . 21-74
Climate Control Unit Removal/Installation . 21-75
Dust and Pollen Filter Replacement . 21-75
Blower Unit Removal/Installation . 21-76
Blower Unit Component Replacement . 21-77
Evaporator Core Replacement . 21-78
Expansion Valve Replacement . 21-80
Heater Unit/Core Replacement . 21-81
A/C Compressor Replacement . 21-83
A/C Compressor Clutch Check . 21-85
A/C Compressor Clutch Overhaul . 21-86
A/C Compressor Thermal Protector
Replacement . 21-87
A/C Compressor Relief Valve Replacement . 21-87
A/C Condenser Replacement . 21-88
Receiver/Dryer Desiccant Replacement . 21-89
Refrigerant Recovery . 21-90
System Evacuation . 21-91
System Charging . 21-92
Refrigerant Leak Check . 21-93
A/C System Noise Check . 21-97
A/C System Test . 21-99
08/08/21 14:40:45 61SNR030_210_0002
ProCarManuals.com
DYNOMITE -2009-

(#'

)Î
Î
(#'

")
21-621-6 Climate Control
A/C Service Tips and Precautions A/C System Inspection
A
 Compressed air mixed with the R-134a forms a
combustible vapor.
 The vapor can burn or explode causing serious injury.
 Never use compressed air to pressure test R-134a service equipment or vehicle air
conditioning systems.
 Air conditioning refrigerant or lubricant vapor can irritate your eyes, nose, or throat.
 Be careful when connecting service equipment.
 Do not breathe refrigerant or vapor.
The air conditioning system uses HFC- 134a (R-134a)
refrigerant and polyalkyleneglycol (PAG) refrigerant oil,
which are not compatible with CFC-12 (R-12) refrigerant
or mineral oil. Do not use R-12 refrigerant or mineral oil
in this system, and do not attempt to use R-12 servicing
equipment; damage to the air conditioning system or
your servicing equipment will result.
Use only service equipment that is U.L.-listed and is
certified to meet the requirements of SAE J2210 to
remove R-134a from the air conditioning system.
If accidental system discharge occurs, ventilate the
work area before resuming service.
R-134a service equipment or vehicle air c onditioning
systems should not be pressure tested or leak tested
with compressed air.
Additional health and safety information may be
obtained from the refrigerant and lubricant
manufacturers.
 Always disconnect the negative cable from the battery whenever replacing air conditioning parts.
 Keep moisture and dirt out of the system. When disconnecting any lines, plug or cap the fittings
immediately; don’t remove the caps or plugs until
just before you reconnect each line.
 Before connecting any hose or line, apply a few drops of refrigerant oil to the O-ring.
 When tightening or loosening a fitting, use a second wrench to support the matching fitting.
 When discharging the system, use an R-134a refrigerant recovery/recycling/charging station; don’t
release refrigerant into the atmosphere. Before troubleshooting any problem with the air
conditioning system, do the following:
1. With the ignition switch in LOCK (0), inspect the A/C components, the pressure lines, and the hoses for
stains that may indicate a refrigerant or a
compressor oil leak.
2. Check the A/C condenser (A) for material clogging the fins or for damage to the fins:
 Carefully clean any material from the A/C condenser fins with water and detergent. If
deeper cleaning is required, clean the fins with
Honda brite cleaner (P/N 08732-0020B).
 Be sure to dry the A/C condenser completely.
 Refer to the Refrigerant Leak Check (see page 21-93) to confirm leaks if there is visible damage
to the A/C condenser.
Check for stains.
08/08/21 14:40:55 61SNR030_210_0007
ProCarManuals.com
DYNOMITE -2009-

Î(#'

 )
21-721-7
A/C Refrigerant Oil Replacement
A
B C
3. Inspect the drive belt (see page 4-30).
4. Make sure no material is blocking the air flow to the
A/C condenser.
5. Check the dust and pollen filter. Replace it if it is clogged (see page 21-75).
6. Check for kinks or sharp bends in the A/C lines and hoses, which can greatly reduce system
performance. Replace A/C lines and hoses if they
are kinked or damaged (see page 21-8).
7. Start the engine, turn the air conditioning system on, and allow it to run for a few minutes and reach
stable operation.
 Check that the A/C operates at each position of the blower fan switch (except OFF). If the A/C
does not operate, refer to the symptom
troubleshooting.
 Check that the A/C compressor clutch (A) is engaged. The pressure plate should be rotating
at the same speed as the pulley. If the pressure
plate does not engage, refer to the symptom
troubleshooting.
 Check that the A/C condenser fan (B) and radiator fan (C) operate when the A/C compressor clutch
is engaged. If either fan fails to operate when the
A/C compressor clutch is engaged, refer to the
symptom troubleshooting.
 Check that the engine idle speed is correctly maintained when the A/C is switched on and off
and the A/C compressor clutch is engaged and
disengaged. Recommended PAG oil: SP-10
P/N 38897-P13-A01AH: 120 mL (4 fl·oz)
It is important to have the correct amount of refrigerant
oil in the A/C system to ensure proper lubrication of the
compressor. Too little oil damages the compressor; too
much oil reduces the cooling capacity of the system,
and can produce high vent temperatures.
 To avoid contamination, do not return the oil to the container once dispensed, and never mix it with other
refrigerant oils.
 Immediately after using the oil, reinstall the cap on the container, and seal it to avoid moisture
absorption.
 Do not spill the refrigerant oil on the vehicle; it may damage the paint; if it gets on the paint, wash it off
immediately.
Add the recommended refrigerant oil in the amount
listed if you replace any of the following parts: ........
.............. ............ ........
..............
........
.............. ............ ........
..............
A/C condenser .50 mL (1 2/3 fl·oz)
Evaporator .40 mL (1 1/3 fl·oz)
Line or hose .10 mL (1/3 fl·oz)
Receiver/Dryer .10 mL (1/3 fl·oz)
Leakage repair .25 mL (5/6 fl·oz)
A/C compressor .Since the oil separator is
equipped inside the compressor
for this vehicle, oil drainage is
unnecessary at the time of
compressor replacement.
08/08/21 14:40:56 61SNR030_210_0008
ProCarManuals.com
DYNOMITE -2009-