2006 ACURA CSX oil


(#'



!)

Type S Model
19-23
INNER PAD SHIM B WEAR INDICATOR
OUTER PAD SHIM A
INNER PAD SHIM A BRAKE PADS CALIPER PIN B
CALIPER PIN
PIN BOOT
12 x 1.25 mm
108 N·m
(11.0 kgf·m,
79.6 lbf·ft) CALIPER
BRACKET
CALIPER PIN A
BLEED SCREW
9N·m
(0.9 kgf·m,
7lbf·ft)
CALIPER
BODY
PAD RETAINERS
PISTON
PISTON BOOT
BRAKE HOSE
BANJO BOLT
34 N·m
(3.5 kgf·m,
25 lbf·ft) PISTON SEAL
: Honda silicone grease (P/N 08C30-B0234M)
SEALING
WASHERS 8x1.0mm
33 N·m
(3.4 kgf·m, 25 lbf·ft)OUTER PAD SHIM B
Frequent inhalation of brake pad dust, regardless of material composition, could be hazardous to your health.
 Avoid breathing dust particles.
 Never use an air hose or brush to clean brake assemblies. Use an OSHA-approved vacuum cleaner.
Remove, disassemble, inspect, reassemble, and install the caliper, and note these items:
NOTE: Make sure that the caliper pins are installed correctly. Upper caliper pin B and lower caliper pin A are different.
If these caliper pins are installed in the wrong location, it will cause vibration, uneven or rapid brake pad wear, and
possibly uneven tire wear.  Do not spill brake fluid on the vehicle; it may damage the paint; if brake fluid gets on the paint, wash it off immediately with water.
 To prevent dripping brake fluid, cover disc onnected hose joints with rags or shop towels.
 Clean all parts in brake fluid and air dry; blow out all passages with compressed air.
 Before reassembling, check that all parts are free of dirt and other foreign particles.
 Replace parts with new ones as specified in the illustration.
 Make sure no dirt or other foreign matter gets in the brake fluid.
 Make sure no grease or oil gets on the brake discs or pads.
 When reusing brake pads, always reinstall them in their original positions to prevent loss of braking efficiency.
 Do not reuse drained brake fluid. Use only clean Honda DOT 3 Brake Fluid from an unopened container. Using a non-Honda brake fluid can cause corrosion and shorten the life of the system.
 Coat the piston, the piston seal groove, and the caliper bore with clean brake fluid.
 Use recommended greases in the front caliper set.
 After installing the caliper, check the brake hose and line for leaks, interference, and twisting.
Install inner brake pad with
its wear indicator upward. Replace.
Replace.
Replace.
Replace.
08/08/21 15:00:59 61SNR030_190_0023
ProCarManuals.com
DYNOMITE -2009-


(#'



!)
19-35
Rear Brake Caliper Overhaul
BRAKE HOSE8x1.0mm
23 N·m
(2.3 kgf·m, 17 lbf·ft)
SEALING WASHERS
BANJO BOLT
34 N·m
(3.5 kgf·m, 25 lbf·ft)
BLEED SCREW
9 N·m (0.9 kgf·m, 7 lbf·ft)
CALIPER BODY
RODO-RING
SLEEVE PISTON
CUP ADJUSTING BOLT
BEARING A
SPACER
ADJUSTING SPRING B
PISTON BOOT
PISTON SEAL
PISTON
ASSEMBLY
CIRCLIP
SPRING
GUIDE
SHAFT
SHAFT COVER
LEVER ARM
SPRING
WASHER PARKING NUT
27 N·m
(2.8 kgf·m, 20 lbf·ft) RETURN
SPRING
23 N·m
(2.3 kgf·m,
17 lbf·ft)
INNER PAD
SHIM BRAKE PADS PAD SPRING
CALIPER PIN A CALIPER PIN B
PAD
RETAINERS
CALIPER
BRACKET
: Honda silicone grease (P/N 08C30-B0234M)
OUTER PAD SHIM
WEAR INDICATOR
CALIPER PIN PIN BOOT 10x1.25mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
Frequent inhalation of brake pad dust, regardless of material composition, could be hazardous to your health.
 Avoid breathing dust particles.
 Never use an air hose or brush to clean brake assemblies. Use an OSHA-approved vacuum cleaner.
Remove, disassemble, inspect, reassemble, and install the caliper, and note these items:
NOTE: Make sure that the caliper pins are installed correctly. Upper caliper pin B and lower caliper pin A are different.
If these caliper pins are installed in the wrong location, it will cause vibration, uneven or rapid pad wear, and possibly
uneven tire wear.  Do not spill brake fluid on the vehicle; it may damage the paint; if brake fluid gets on the paint, wash it off immediately with water.
 To prevent dripping brake fluid, cover disc onnected hose joints with rags or shop towels.
 Clean all parts in brake fluid and air dry; blow out all passages with compressed air.
 Before reassembling, check that all parts are free of dirt and other foreign particles.
 Replace parts with new ones as specified in the illustration.
 Make sure no dirt or other foreign matter gets into the brake fluid.
 Make sure no grease or oil gets on the brake discs or pads.
 When reusing brake pads, always reinstall them in their original positions to prevent loss of braking efficiency.
 Do not reuse drained brake fluid. Use only clean Honda DOT 3 Brake Fluid from an unopened container. Using a non-Honda brake fluid can cause corrosion and shorten the life of the system.
 Coat the piston, the piston seal groove, and the caliper bore with clean brake fluid.
 Use recommended greases in the rear caliper set.
 After installing the caliper, check the brake hose and line for leaks, interference, and twisting.
Replace.
Replace.
Replace. Replace.
Replace.
Replace.
Install inner pad
with its wear
indicator downward. Replace.
08/08/21 15:02:07 61SNR030_190_0035
ProCarManuals.com
DYNOMITE -2009-

Seats
Bumpers
Hood
Trunk Lid
Fuel Fill Door
Exterior TrimFenderwell
Openers
Frame......................
............................................... ...............
................ .......
........................................... .........................
..............................
........................................... ......................
........................................... ...
...
......................
............................................... ...............
................ .......
........................................... .........................
..............................
........................................... ......................
........................................... ...
...
Component Location Index
. 20-116
Front Seat Active Head Restraint Inspection . 20-117
Front Seat Removal/Installation . 20-118
Front Seat Frame Replacement . 20-120
Front Seat-back Cover Replacement . 20-123
Front Seat Cushion Cover Replacement . 20-127
Rear Seat Removal/Installation . 20-131
Rear Seat-back Latch Replacement . 20-135
Rear Seat-back Release Lever/Cable Removal/Installation . 20-136
Rear Seat Armrest Beverage Holder Replacement . 20-137
Rear Seat Armrest Replacement . 20-138
Rear Seat-back Cover Replacement . 20-139
Rear Seat Side Bolster Cover Replacement . 20-143
Rear Seat Cushion Cover Replacement . 20-143
Rear Seat Armrest Cover Replacement . 20-144
.........
...........................................
........................................... ..........
........................................... .........
...........................................
........................................... ..........
...........................................
Front Bumper Removal/Installation . 20-146
Front Bumper Lower Grille
Replacement . 20-148
Front Bumper Lower Side Plate Replacement . 20-148
Rear Bumper Removal/Installation . 20-149
Rear Bumper Lower Cover Replacement . 20-151
...................................... ................................................
......................................
................................................
Hood Adjustment
. 20-152
Hood Seal Replacement . 20-153
Hood Insulator Replacement . 20-154
................................ ..............
..............
................................
..............
..............
Trunk Lid Adjustment
. 20-155
Trunk Lid Torsion Bar Replacement . 20-156
Trunk Lid Weatherstrip Replacement . 20-157
Trunk Lid Cushion Replacement . 20-157
.........................................
.........................
................
Fuel Fill Door Adjustment
. 20-158
Fuel Cap Adapter Replacement . 20-159
........................................
...............
.......................... ......................
...................... ...
..............
................
..................
..........................
..............
...............
.......................... ......................
...................... ...
..............
................
..................
Front Grille Replacement
. 20-160
Front Fender Trim Replacement . 20-162
Front Grille Cover Replacement . 20-163
Cowl Cover Replacement . 20-163
Roof Molding Replacement . 20-165
Door Molding Replacement . 20-167
Side Sill Protection Tape Replacement . 20-168
Rear License Trim Replacement . 20-168
Trunk Lid Spoiler Replacement . 20-169
Emblem/Sticker Replacement . 20-170 .............
...................... ............
......
.............
.............
......................... .................... .............
...................... ............
......
.............
.............
......................... ....................
Front Inner Fender Replacement . 20-171
Splash Shield Replacement
. 20-172
Front Fender Fairing Replacement . 20-173
Middle Floor Undercover Replacement . 20-174
Rear Floor Undercover Replacement . 20-174
Fuel Pipe Protector Replacement . 20-175
Rear Fender Cover Replacement . 20-175
Rear Strake Replacement . 20-176
Rear Air Outlet Replacement . 20-176
...................... ............
..................
..........................
........................................... .....
...................
......................
............
..................
..........................
........................................... .....
...................
Component Location Index
. 20-177
Hood Opener Cable Replacement . 20-178
Trunk Lid Opener Cable/Fuel Fill Door Opener Cable Replacement . 20-179
Hood Latch Replacement . 20-181
Trunk Lid Opener/Fuel Fill Door Opener Replacement . 20-182
Trunk Lid Lock Cylinder Replacement . 20-184
Trunk Lid Latch Replacement . 20-185
...........................................
........................................... ............................
...................................
...........................................
...........................................
............................
...................................
Upper Dashboard Support Gusset
Replacement . 20-186
Rear Floor Upper Cross-member Gusset Replacement . 20-186
Subframe Replacement . 20-187
Frame Repair Chart . 20-188
08/08/21 14:58:49 61SNR030_200_0003
ProCarManuals.com
DYNOMITE -2009-


Rubber dams adhesive tape:
Thickness 0.16 mm (0.006 in.)
Width 3.5 mm (0.14 in.)
Clips adhesive tape: Thickness 0.4 mm (0.016 in.)
Width 10 mm (0.39 in.)
20-39
Inside 11 mm
(0.43 in.)
B
D
12.3 mm
(0.48 in.) B
A
CE
E
E
AC B
D
12.3 mm
(0.48 in.)
12.8 mm
(0.5 in.) F
8. Scrape smooth the old adhesive, using a puttyknife or similar tool, until there is a thickness of
about 2 mm (0.08 in.) on the bonding surface
around the entire windshield opening flange:
 Do not scrape down to the painted surface of the body; damaged paint will interfere with proper
bonding.
 Remove the rubber dam and fasteners from the body.
 Replace the dashboard seal with a new one.
9. Clean the body bonding surface with a shop towel dampened in isopropyl alcohol. After cleaning,
keep oil, grease and water from getting on the
clean surface.
10. If the old windshield will be reinstalled, scrape off the old adhesive, the fasteners, and the rubber dam
from the windshield with a putty knife. Clean the
bonding surfaces on the inside face and the edge of
the windshield with isopropyl alcohol. Make sure
the bonding surface is kept free of water, oil, and
grease. 11. Attach the upper rubber dam (A), the lower rubber
dam (B), and the clips (C) with adhesive tape to the
inside face of the windshield (D) as shown:
 Be sure the rubber dam and the clips line up with the alignment marks (E).
 Be sure the convex portion (F) of the left and the right clips faces the left side.
 Be careful not to touch the windshield where adhesive will be applied.
(cont’d)
08/08/21 15:00:08 61SNR030_200_0041
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
20-43
Front Corner Glass Replacement
A B A
B
C
D
Fastener Locations
:Clip,2
A :Clip,2
B
A
B
NOTE:
 Put on gloves to protect your hands.
 Wear eye protection while cutting the glass adhesive.
 Use seat covers to avoid damaging any surface.
1. Remove the A-pillar trim (see page 20-69).
2. From inside the vehicle, cut through the front corner glass adhesive (A) with a utility knife (B) all
the way around. Apply protective tape along the
edge of the entire front corner glass opening flange. 3. From outside the vehicle, pry the front corner glass
clips (A) and the front corner trim clips (B), then
carefully remove the glass (C) and the trim (D)
together. The trim is not attached to the glass.
4. Scrape smooth the old adhesive, using a putty knife or similar tool, until there is a thickness of
about 2 mm (0.08 in.) on the bonding surface
around the entire front corner glass opening flange:
 Do not scrape down to the painted surface of the body; damaged paint will interfere with proper
bonding.
 If any of the clips are broken, remove them from the body.
5. Clean the body bonding surface with a sponge applicator dampened in isopropyl alcohol. After
cleaning, keep oil, grease, and water from getting
on the surface.
6. If the old front corner glass will be reinstalled, scrape off the old adhesive with a putty knife from
the front corner glass. Clean the bonding surfaces
on the inside face of the front corner glass and the
edge of the glass with isopropyl alcohol. Make sure
the bonding surface is kept free of water, oil and
grease.
(cont’d)
08/08/21 15:00:10 61SNR030_200_0045
ProCarManuals.com
DYNOMITE -2009-



Cutting positions
20-48 Glass
Rear Window Replacement (cont’d)
A
B
AB
A B
C A
B C
A
A AA
6. Remove the lower rubber dam (A) from the lower
edge of the rear window (B). If necessary, cut the
rubber dam with a utility knife.
7. With a helper on the outside, pull the piano wire (A) back and forth in a sawing motion. Hold the piano
wire as close to the rear window (B) as possible to
prevent damage to the body, and carefully cut
through adhesive (C) around the entire rear
window. 8. Carefully remove the rear window.
9. Scrape smooth the old adhesive, using a putty
knife or similar tool, until there is a thickness of
about 2 mm (0.08 in.) on the bonding surface
around the entire rear window opening flange:
 Do not scrape down to the painted surface of the body; damaged paint will interfere with proper
bonding.
 Remove the fasteners from the body.
10. Clean the body bonding surface with a shop towel dampened in isopropyl alcohol. After cleaning,
keep oil, grease, and water from getting on the
surface.
11. If the old rear window will be reinstalled, scrape off the old adhesive, the fasteners, and the rubber dam
from the rear window with a putty knife. Clean the
bonding surfaces on the inside face and the edge of
the rear window with isopropyl alcohol. Make sure
the bonding surface is kept free of water, oil, and
grease.
08/08/21 15:00:13 61SNR030_200_0050
ProCarManuals.com
DYNOMITE -2009-



(#'
 )

Passenger’s Seat
20-12020-120 Seats
Front Seat Removal/Installation
(cont’d)
Front Seat Frame Replacement
Fastener Locations
:Bolt,4
10x1.25mm
34 N·m
(3.5 kgf·m, 25 lbf·ft) A
A
B
C
Fastener Locations
:Clip,4
A
9. With the help of an assistant, carefully remove thefront seat through the front door opening.
10. Install the seat in the reverse order of removal, and note these items:
 Apply medium strength liquid thread lock to the seat mounting bolts before reinstallation.
 Tighten the seat mounting bolts to the specified torque in the sequence shown. Slide the seat (A)
all the way back and tighten and , then slide
it forward and tighten and . The driver’s seat
is shown; the passenger’s seat is similar.
 Tighten the bolts by hand first, then tighten them to specification with a torque wrench.
 Make sure each connector is plugged in properly.
 Check for any DTCs that may have been set during repairs, and clear them.
 Do the battery terminal reconnection procedure (see page 22-68). Calibrate the ODS unit after any of these actions
(see page 24-27):
 Front passenger’s seat replacement (including any seat components)
 Replacement of the front seat weight sensors
 After a vehicle collision
NOTE:  Put on gloves to protect your hands.
 Apply oil to the pivot portions of the slide locks.
 Apply multipurpose grease to the sliding portions of the seat tracks.
 If the side airbag has deployed, replace the seat frame and related pieces with new ones (see page
24-185).
1. Remove the front seat (see page 20-118).
2. Remove these items:  Front seat-back cover (see page 20-123)
 Front seat cushion cover (see page 20-127)
 ODS unit (see page 24-209)
 Front seat belt buckle (see page 24-6)
3. Remove the clips, then remove the recline inner covers (A) and module holder (B) from the seat
frame (C).
08/08/21 15:03:55 61SNR030_200_0122
ProCarManuals.com
DYNOMITE -2009-



(#'
 )

Passenger’s Seat
20-12020-120 Seats
Front Seat Removal/Installation
(cont’d)
Front Seat Frame Replacement
Fastener Locations
:Bolt,4
10x1.25mm
34 N·m
(3.5 kgf·m, 25 lbf·ft) A
A
B
C
Fastener Locations
:Clip,4
A
9. With the help of an assistant, carefully remove thefront seat through the front door opening.
10. Install the seat in the reverse order of removal, and note these items:
 Apply medium strength liquid thread lock to the seat mounting bolts before reinstallation.
 Tighten the seat mounting bolts to the specified torque in the sequence shown. Slide the seat (A)
all the way back and tighten and , then slide
it forward and tighten and . The driver’s seat
is shown; the passenger’s seat is similar.
 Tighten the bolts by hand first, then tighten them to specification with a torque wrench.
 Make sure each connector is plugged in properly.
 Check for any DTCs that may have been set during repairs, and clear them.
 Do the battery terminal reconnection procedure (see page 22-68). Calibrate the ODS unit after any of these actions
(see page 24-27):
 Front passenger’s seat replacement (including any seat components)
 Replacement of the front seat weight sensors
 After a vehicle collision
NOTE:  Put on gloves to protect your hands.
 Apply oil to the pivot portions of the slide locks.
 Apply multipurpose grease to the sliding portions of the seat tracks.
 If the side airbag has deployed, replace the seat frame and related pieces with new ones (see page
24-185).
1. Remove the front seat (see page 20-118).
2. Remove these items:  Front seat-back cover (see page 20-123)
 Front seat cushion cover (see page 20-127)
 ODS unit (see page 24-209)
 Front seat belt buckle (see page 24-6)
3. Remove the clips, then remove the recline inner covers (A) and module holder (B) from the seat
frame (C).
08/08/21 15:03:55 61SNR030_200_0122
ProCarManuals.com
DYNOMITE -2009-