2006 ACURA CSX navigation

[x] Cancel search: navigation

catalytic converter oil dipstick isofix transmission mirror controls oil viscosity

Load previous 8 pages

Page 2492 of 2893

ACURA CSX 2006 Service Repair Manual ´
µ
´
µ
´
µ
´
µ
Î Î
´
µ
µ µ
µ
Speaker Terminal Wire color
YES
NO YES
NO
23-208Audio System
Symptom Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR A (24P)
ST

Page 2493 of 2893

ACURA CSX 2006 Service Repair Manual Î

Î

Î

µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
23-209
STEREO AMPLIFIER CONNECTOR A (20P)
ACC RADIO (PUR)
STEREO AMPLIFIER CONNECTOR B (14P) AMP ON (LT BLU) STEREO AMPLIFIER CONNEC

Page 2495 of 2893

ACURA CSX 2006 Service Repair Manual Î
Î

µ
µµ µ
Stereo amplifier connector Wire color
YES
NO Navigation
unit connector Stereo
amplifier
connector Wire color
YES
NO
23-211
STEREO AMPLIFIER CONNECTOR B (14P) STEREO AMPLI

Page 2496 of 2893

Page 2497 of 2893

Page 2498 of 2893

Page 2499 of 2893

ACURA CSX 2006 Service Repair Manual (##
)
µ
µ
µ
µ µ
µ
µ
µ
No sound is heard from the speaker(s)
(display is normal) (without navigation)
YES
NO
YES
NO YES
NO
YES
NO
23-215
NOT

(#'#
)
µ
µ
µ
µ µ
µ
µ
µ
No sound is heard from the speaker(s)
(display is normal) (without navigation)
YES
NO
YES
NO YES
NO
YES
NO
23-215
NOTE:
Check the vehicle battery condition first.
Check the connectors for poor connections or loose terminals.
Set the fader and balance positions to the center.
Before performing symptom troubleshooting, do the power switch will not turn on troubleshooting
(see page 23-203).
For vehicles with factory installed audio, do the self- diagnostic function, speaker check (see page 23- 192)
to help isolate the speaker.
1. Turn the ignition switch to ON (II).
2. Check that the volume button is not set to the MIN level.
Raise the volume level, and recheck the
function.
Go to step 3.
3. Do the speaker check mode in the self-diagnostic function (see page 23-192).
Speaker(s) failed the test:
If at least one speaker is OK, go to step 4.
If all speakers fail to sound, go to step 7.
Speakers all work, but sound quality is poor:
If the sound is poor only with AM or FM, go to poor AM or FM radio reception or interference
(see page 23-199).
If the sound is poor only with disc. – Try several known- good disc in the audio unit.
– If the sound quality is normal, the original disc is faulty.
– If the sound quality is still poor, replace the audio unit.
If the sound is poor in all modes, go to sound quality diagnosis (see page 23-251).
4. Turn the ignition switch to LOCK (0). 5. Remove the speaker(s) with no sound (see page
23-259), and disconnect its connector.
6. Check the speaker 2P connector for a loose or poor connection.
Go to step 7.
Operation is normal.
7. Make sure the ignition switch is in LOCK (0).
8. Remove the speaker(s) with no sound (see page 23-259), and disconnect its connector.
9. Measure the resistance between terminals No. 1 and No. 2 of the speaker connector.
Go to step 10.
Faulty speaker(s).
10. Remove the audio unit (see page 23-256). Disconnect audio unit connector A (17P).
NOTE: Eject all the discs before removing the audio
unit to prevent damaging the CD player’s load
mechanism.
(cont’d)
Is i t at M IN l ev el ?Do any or al l of t he speak er s f ai l t o sound ? Reconnect t he speak er 2P connect or and r echeck
the symptom; does it still f ail?
Is t her e about 4 ?
08/08/21 14:10:47 61SNR030_230_0218
ProCarManuals.com
DYNOMITE -2009-

Page 2501 of 2893

ACURA CSX 2006 Service Repair Manual Î
(#
)

µ
µ
µ
µ
µ
µ µ
µ
µ
µ
Auxiliary input sound is low or cannot be
heard
YES
NO
YES
NO
YES
NO YES
NO
Navigation unit connector

Î
(#'
)

µ
µ
µ
µ
µ
µ µ
µ
µ
µ
Auxiliary input sound is low or cannot be
heard
YES
NO
YES
NO
YES
NO YES
NO
Navigation unit connector Wire color
YES
NO
23-217
NAVIGATION UNIT CONNECTOR B (24P)
NOTE: Check the vehicle battery condition first.
Check the connectors for poor connections or loose terminals.
Use auxiliary stereo cables with 3.5 mm ends only.
Auxiliary accessories may be played on the audio unit using the auxiliary input.
1. Turn the ignition switch to ON (II).
2. Turn on the audio unit or navigation unit and connect an aux iliary accessory to the auxiliary
input jack.
3. Check the volume operation.
Operation is normal at this time.
Go to step 4.
4. Make sure the auxiliary accessory volume to max.
Go to step 5.
Raise the auxiliary accessory volume is set to
high. Make sure the audio unit volume is turned
down before retesting.
5. Substitute a known-good aux iliary audio accessory
and/or auxiliary stereo cable, and recheck.
Original auxiliary audio accessory or
auxiliary stereo cable is faulty.
Go to step 6.
6. Turn the ignition switch to LOCK (0). 7. Remove the auxiliary jack assembly (see page
23-261), and check that the auxiliary jack assembly
is properly connected.
With navigation: go to step 8.
Without navigation: go to step 13. Reconnect the connector, and recheck the
function.
8. Disconnect aux iliary jack assembly 5P connector.
9. Disconnect navigation unit connector B (24P).
10. Check for continuity between body ground and navigation unit connector B (24P) according to the
table.
B1 BRN
B3 BLU
B13 YEL
B14 GRN
B15 WHT
Short to body ground in the wire(s) between
the navigation unit and the auxiliary jack assembly.
Replace the affected shielded harness.
Go to step 11.
(cont’d)
Wire side of female terminals
I s t he sound nor mal ?Isthevolumeset tohigh?
Does the auxiliary audio accessory operatepr oper l y ? Is the auxiliary jack assembly c
onnect ed
pr oper l y ?
Is there continuity?
08/08/21 14:10:48 61SNR030_230_0220
ProCarManuals.com
DYNOMITE -2009-

Load next 8 pages

Page: < prev 1-10 ... 185-192 193-200 201-208 209-216 217-224 225-232 233-240 241-248 249-256 ... 376 next >

wheel steering wheel adjustment jump cable fuse box diagram coolant reservoir lights