´
µ ´
µ
´
µ ´
µ
Î
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
Speaker Terminal Wire color
YES
NO
23-40 Audio System
Symptom Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR A (17P)
5. Check to see if there is a specific speaker that has
no sound.
Speaker(s) failed the test:
If at least one speaker is OK, go to step 6.
If all speakers fail to sound: – With premium audio system: Go to step 14.
– Without premium audio system: Go to step 9.
Speakers all work, but sound quality is poor in
step 1.
If sound is poor only with XM radio, or the XM radio does not function, go to poor or no sound
with XM radio (see page 23-72).
If the sound is poor only with AM or FM, go to poor AM or FM radio reception or interference
(see page 23-29).
If the sound is poor only with disc. – Try several known- good disc in the navigation
unit.
– If the sound quality is normal, the original disc is faulty.
– If the sound quality is still poor, replace the navigation unit.
If the sound is poor in all modes, go to sound quality diagnosis (see page 23-74).
6. Turn the ignition switch to LOCK (0).
7. Remove the speaker(s) with no sound (see page 23-83), and disconnect its connector.
8. Check the speaker 2P connector for a loose or poor connection.
Go to step 9.
Operation is normal.
9. Make sure the ignition switch is in LOCK (0). 10. Measure the resistance between terminals No. 1
and No. 2 of the speaker connector.
With premium audio system: Go to step 20.
Without premium audio system: Go to step 11. Faulty speaker(s).
11. Remove the navigation unit (see page 23-155). Disconnect navigation unit connector A (17P).
NOTE: Eject all the discs before removing the navigation unit to prevent damaging the CD player’s load
mechanism.
Remove the PC card before removing the navigation unit.
12. Measure the resistance between the following terminals of navigation unit connector A (17P)
accordingtothetable.
Driver’s door speaker,
Left tweeter A12 ( ) LT GRN
A3 ( ) PNK
Front passenger’s
door speaker,
Right tweeter A15 ( ) GRY
A7 ( ) BRN
Left rear speaker A11 ( ) YEL A2 ( ) BRN
Right rear speaker A16 ( ) BLU A8 ( ) ORN
Go to step 13.
Repair open or short in the wires between
navigation unit and the speaker(s).
Wire side of female terminals
Do any or al l of t he speak er s f ai l t o sound ?
Reconnect t he speak er 2P connect or , and r echeckthe symptom; does it still f ail? Is t her e about 4 ?
Is t her e about 4 ?
08/08/21 14:04:41 61SNR030_230_0043
ProCarManuals.com
DYNOMITE -2009-
Î
Î
Î
µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
23-42Audio System
Symptom Troubleshooting (cont’d)
STEREO AMPLIFIER CONNECTOR A (20P)
ACC RADIO (PUR)
STEREO AMPLIFIER CONNECTOR B (14P) AMP ON (LT BLU) STEREO AMPLIFIER CONNECTOR A (20P)
GND (BLK)
15. Turn the ignition switch to ON (II).
16. Measure the voltage between stereo amplifierconnector A (20P) terminal No. 9 and body ground.
Go to step 17.
Repair open in the wire between the No. 35
(7.5 A) fuse in the under-dash fuse/relay box and
stereo amplifier connector A (20P) terminal No. 9.
17. Measure the voltage between stereo amplifier connector B (14P) terminal No. 7 and body ground.
Go to step 18.
Repair open in the wire between the stereo
amplifier connector B (14P) terminal No. 7 and
navigation unit connector B (22P) terminal
No. 20. 18. Measure the voltage between stereo amplifier
connector A (20P) terminal No. 20 and body ground.
Go to step 19.
Repair open in the wire between stereo
amplifier connector A (20P) terminal No. 20 and
body ground (G 601).
19. Turn the ignition switch to LOCK (0).
Wire side of female terminals
Wire side of female terminals Wire side of female terminals
Is there battery voltage?
Is there battery voltage? I s t her e l ess t han 0.1 V on bot h t er mi nal s?
08/08/21 14:04:41 61SNR030_230_0045
ProCarManuals.com
DYNOMITE -2009-
(#'#
)
µ
µ
µ
µ µ
µ
µ
µ
No sound is heard from the speaker(s)
(display is normal) (without navigation)
YES
NO
YES
NO YES
NO
YES
NO
23-48Audio System
Symptom Troubleshooting (cont’d)
NOTE:
Check the vehicle battery condition first.
Check the connectors for poor connections or loose terminals.
Set the fader and balance positions to the center.
Before performing symptom troubleshooting, do the power switch will not turn on troubleshooting
(see page 23-36).
For vehicles with factory installed audio, do the self- diagnostic function, speaker check (see page 23-25) to
help isolate the speaker.
1. Turn the ignition switch to ON (II).
2. Check that the volume button is not set to the MIN level.
Raise the volume level, and recheck the
function.
Go to step 3.
3. Do the speaker check mode in the self-diagnostic function (see page 23-25).
Speaker(s) failed the test:
If at least one speaker is OK, go to step 4.
If all speakers fail to sound, go to step 7.
Speakers all work, but sound quality is poor:
If the sound is poor only with AM or FM, go to poor AM or FM radio reception or interference
(see page 23-32).
If the sound is poor only with disc. – Try several known- good disc in the audio unit.
– If the sound quality is normal, the original disc is faulty.
– If the sound quality is still poor, replace the audio unit.
If the sound is poor in all modes, go to sound quality diagnosis (see page 23-74).
4. Turn the ignition switch to LOCK (0). 5. Remove the speaker(s) with no sound (see page
23-83), and disconnect its connector.
6. Check the speaker 2P connector for a loose or poor connection.
Go to step 7.
Operation is normal.
7. Make sure the ignition switch is in LOCK (0).
8. Remove the speaker(s) with no sound (see page 23-84), and disconnect its connector.
9. Measure the resistance between terminals No. 1 and No. 2 of the speaker connector.
Go to step 10.
Faulty speaker(s).
10. Remove the audio unit (see page 23-80). Disconnect audio unit connector A (17P).
NOTE: Eject all the discs before removing the audio
unit to prevent damaging the CD player’s load
mechanism.
Is i t at M IN l ev el ?
Do any or al l of t he speak er s f ai l t o sound ? Reconnect t he speak er 2P connect or , and r echeck
the symptom; does it still f ail?
Is t her e about 4 ?
08/08/21 14:04:43 61SNR030_230_0051
ProCarManuals.com
DYNOMITE -2009-
Î
(#'
)
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
Auxiliary input sound is low or cannot be
heard
YES
NO
YES
NO
YES
NO YES
NO
Navigation unit connector Wire color
YES
NO
23-50 Audio System
Symptom Troubleshooting (cont’d)
NAVIGAION UNIT CONNECTOR B (22P)
NOTE:
Check the vehicle battery condition first.
Check the connectors for poor connections or loose terminals.
Use auxiliary stereo cables with 3.5 mm ends only.
Auxiliary accessories may be played on the audio unit using the auxiliary input.
1. Turn the ignition switch to ON (II).
2. Turn on the audio unit or navigation unit and connect an aux iliary accessory to the auxiliary
input jack.
3. Check the volume operation.
Operation is normal at this time.
Go to step 4.
4. Make sure the auxiliary accessory volume to max.
Go to step 5.
Raise the auxiliary accessory volume is set to
high. Make sure the audio unit volume is turned
down before retesting.
5. Substitute a known-good aux iliary audio accessory
and/or auxiliary stereo cable, and recheck.
Original auxiliary audio accessory or
auxiliary stereo cable is faulty.
Go to step 6.
6. Turn the ignition switch to LOCK (0). 7. Remove the auxiliary jack assembly (see page
23-85), and check that the auxiliary jack assembly is
properly connected.
With navigation: go to step 8.
Without navigation: go to step 13. Reconnect the connector, and recheck the
function.
8. Disconnect aux iliary jack assembly 5P connector.
9. Disconnect navigation unit connector B (22P).
10. Check for continuity between body ground and navigation unit connector B (22P) according to the
table.
B1 BRN
B3 BLU
B11 YEL
B12 GRN
B13 WHT
Short to body ground in the wire(s) between
the navigation unit and the auxiliary jack assembly.
Replace the affected shielded harness.
Go to step 11.
Wire side of female terminals
I s t he sound nor mal ?
Isthevolumeset tohigh?
Does the auxiliary audio accessory operatepr oper l y ? Is the auxiliary jack assembly c
onnect ed
pr oper l y ?
Is there continuity?
08/08/21 14:04:43 61SNR030_230_0053
ProCarManuals.com
DYNOMITE -2009-
(#'
)
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
Radio preset memory is lost Volume does not change
YES
NO
YES
NO YES
NO
YES
NO
23-5423-54Audio System
Symptom Troubleshooting (cont’d)
NOTE: If only the XM stations are lost, go to XM radio
preset memory is lost (see page 23-71).
1. Set each of the radio station preset buttons.
Go to step 2.
With navigation: Replace the navigation unit (see page 23-155).
Without navigation: Replace the audio unit (see page 23-80).
2. Turn the ignition switch to LOCK (0) for 1 minute, then turn it back to ON (II).
3. Test the preset buttons for proper recall operation.
System is normal at this time. Check the
connections at the navigation unit or audio unit.
With navigation: Replace the navigation unit (see page 23-155).
Without navigation: Replace the audio unit (see page 23-80). NOTE:
Check the vehicle battery condition first.
Check the connectors for poor connections or loose terminals.
Set the fader and balance positions to the center.
1. Listen for sound from the speakers.
Go to step 2.
Go to audio system sound is weak or
distorted, or no sound is heard from speaker(s)
(see page 23-39).
2. Operate the volume knob to see if the volume changes.
Operation is normal.
With navigation: Replace the navigation unit (see page 23-155).
Without navigation: Replace the audio unit (see page 23-80).
Do each of t he but t ons set pr oper l y ?
Do the preset buttons recall the set radio stations? I s t he sound nor mal ?
Does t he v ol ume change?
08/08/21 14:04:44 61SNR030_230_0057
ProCarManuals.com
DYNOMITE -2009-
Î
Î
(#'#
)
µ µ
´
µ
µ
µ
µ µ
µ
µ
µ
Navigation unit button illumination does not
work (with navigation)
YES
NO
YES
NO YES
NO
YES
NO
23-58Audio System
Symptom Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR A (17P)
ILL (RED)
GAUGE CONTROL MODULE (TACH) 36P CONNECTOR ILL (RED)
NAVIGATION UNIT CONNECTOR A (17P) ILL (GRY)NOTE: Check the vehicle battery condition first.
Check the connectors for poor connections or loose terminals.
1. Turn the ignition switch to ON (II).
2. Turn the combination lighting switch to the parking light position.
3. Check the illumination of the navigation unit buttons.
Intermittent problem: the navigation unit is
OK at this time. Check for loose or poor
connections at navigation unit connector A (17P).
Go to step 4.
4. Check the illumination of several other buttons not related to the navigation system.
Go to step 5.
Troubleshoot the interior lights. Start by
checking the No. 14 (7.5 A) fuse in the under-dash
fuse/relay box. If the fuse is OK, check for an open
in the wire between the under-dash fuse/relay box
and the navigation unit.
5. Turn the ignition switch to LOCK (0).
6. Disconnect navigation unit connector A (17P). NOTE: Eject all the discs before removing the navigation unit to prevent damaging the CD player’s load
mechanism.
Remove the PC card before removing the navigation unit.
7. Disconnect gauge control module (tach) 36P connector. 8. Check for continuity between navigation unit
connector A (17P) terminal No. 1 and gauge control
module (tach) 36P connector terminal No. 14.
Go to step 9.
Repair open in the wire between the gauge
control module and the navigation unit.
9. Turn the ignition switch to ON (II).
10. With the headlight switch still on, measure the voltage between navigation unit connector A (17P)
terminal No. 10 and body ground.
Check the connections at navigation unit
connector A (17P). If all connections are OK, replace
the navigation unit (see page 23-155).
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminalsAre the buttons illuminated?
Are the buttons illuminated? Is there continuity?
Is there battery voltage?
08/08/21 14:05:30 61SNR030_230_0061
ProCarManuals.com
DYNOMITE -2009-
Î
Î
(#'#
)
µ µ
´
µ
µ
µ
µ µ
µ
µ
µ
Audio unit button illumination does not
work (without navigation)
YES
NO
YES
NO YES
NO
YES
NO
23-59
AUDIO UNIT CONNECTOR A (17P)
ILL (RED)
GAUGE CONTROL MODULE (TACH) 36P CONNECTOR ILL (RED)
AUDIO UNIT CONNECTOR A (17P) ILL (GRY)NOTE: Check the vehicle battery condition first.
Check the connectors for poor connections or loose terminals.
1. Turn the ignition switch to ON (II).
2. Turn the combination lighting switch to the parking light position.
3. Check the illumination of the audio unit buttons.
Intermittent problem: the audio unit is OK at
this time. Check for loose or poor connections at
the audio unit connector A (17P).
Go to step 4.
4. Check the illumination of several other buttons not relatedtotheaudiosystem.
Go to step 5.
Troubleshoot the interior lights. Start by
checking the No. 14 (7.5 A) fuse in the under-dash
fuse/relay box. If the fuse is OK, check for an open
in the wire between the under-dash fuse/relay box
and the audio unit.
5. Turn the ignition switch to LOCK (0).
6. Disconnect audio unit connector A (17P). NOTE: Eject all the discs before removing the audio
unit to prevent damaging the CD player’s load
mechanism.
7. Disconnect gauge control module (tach) 36P connector. 8. Check for continuity between audio unit connector
A (17P) terminal No. 1 and gauge control module
(tach) 36P connector terminal No. 14.
Go to step 9.
Repair open in the wire between the gauge
control module and the audio unit.
9. Turn the ignition switch to ON (II).
10. With the headlight switch still on, measure the voltage between audio unit connector A (17P)
terminal No. 10 and body ground.
Check the connections at audio unit
connector A (17P). If all the connections are OK,
replace the audio unit (see page 23-80).
Repair open in the wire between the under-
dash fuse/relay box and the audio unit.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Are the buttons illuminated?
Are the buttons illuminated? Is there continuity?
Is there battery voltage?
08/08/21 14:05:31 61SNR030_230_0062
ProCarManuals.com
DYNOMITE -2009-
Î
(#'#
)
´
µµ
µ
µ
µ
µ
µ µ
µ
Display does not dim or brighten with
dimmer (without navigation)
YES
NO
YES
NO
YES
NO YES
NO
23-60Audio System
Symptom Troubleshooting (cont’d)
AUDIO UNIT CONNECTOR A (17P)
ILL (GRY)
ILL (RED)
NOTE:
Check the vehicle battery condition first.
Check the connectors for poor connections or loose terminals.
1. Turn the ignition switch to ON (II).
2. Turn the combination light switch ON and OFF to see if the symptom can be duplicated.
Go to step 3.
Operation is normal.
3. Turn the combination light switch to OFF.
4. Rotate the illumination control dial.
Operation is normal.
Go to step 5.
5. Disconnect, and check audio unit connector A (17P) for a loose or a poor connection.
NOTE: Eject all the discs before removing the audio
unit to prevent damaging the CD player’s load
mechanism.
Go to step 6.
Operation is normal.
6. Turn the ignition switch to LOCK (0).
7. Remove the audio unit (see page 23-80). 8. Turn the ignition switch to ON (II).
9. Measure the voltage between audio unit connector
A (17P) terminals No. 1 and No. 10. Rotate the dash
brightness controller buttons to see if the voltage
changes.
Substitute a known-good audio unit
(see page 23-80), and recheck. If the symptom/
indication goes away, replace the original audio
unit. If symptom is still present, substitute a known-
good center panel display and recheck. If the
symptom/indication goes away, replace the
original center panel display (see page 23-80).
Repair open in the wire between the under-
dash fuse/relay box and the gauge control
module.
Wire side of female terminals
Is it duplicated?
Does the illumination dim and brighten normally asy ou r ot at e t he d i al ?
Reconnect aud i o uni t connect or A ( 17 P), andr echeck t he sy mpt om; d oes i t st i l l appear ? Does t he v ol t age change?
08/08/21 14:05:31 61SNR030_230_0063
ProCarManuals.com
DYNOMITE -2009-