2006 ACURA CSX lock

Î
Î
(#'#
)
´
µ
µ
µ
µ µ
µ
µ
µ
No picture is displayed
YES
NO
YES
NO YES
NO
YES
NO
23-119
Symptom Troubleshooting
NAVIGATION UNIT CONNECTOR A (17P)
BBACKUP(WHT)
NAVIGATION UNIT CONNECTOR A (17P) ACC RADIO (PUR)
NOTE: Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation system anti-theft code.
1. Check the No. 23 (10 A) fuse in the under-hood fuse/relay box and No. 35 (7.5 A) fuse in the under-
dash fuse/relay box, and reinstall the fuse if it is OK.
Go to step 2.
Replace the fuse and recheck.
2. Turn the ignition switch to ON (II).
3. Operate the radio and listen to the audio.
Go to step 4.
Refer to audio system troubleshooting.
4. Turn the ignition switch to LOCK (0).
5. Remove the navigation unit (see page 23-155). 6. Measure the voltage between navigation unit
connector A (17P) terminal No. 17 and body ground.
Go to step 7.
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
7. Turn the ignition switch to ON (II).
8. Measure the voltage between navigation unit connector A (17P) terminal No. 14 and body ground.
Go to step 9.
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
(cont’d)
Wire side of female terminals
Wire side of female terminals
IsthefuseOK? Can y ou hear t he aud i o? Is there battery voltage?
Is there battery voltage?
08/08/21 14:07:25 61SNR030_230_0122
ProCarManuals.com
DYNOMITE -2009-

(#'#
)

µ
µ
µ
µ
YES
NO
YES
NO
Navigation display buttons do not work or
respond properly
23-12123-121
5. Turn the ignition switch to LOCK (0), then turn toON (II) and observe the navigation picture.
Check for sources of electrical noise, such as
poor battery connection, alternator, defective
battery, aftermarket accessories or cell phone, and
poor pin fits at the navigation unit.
Replace the navigation unit (see page 23-155). NOTE:
 Check the vehicle battery condition first.
 Always make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Always check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation and audio system anti-theft codes.
1. Turn the ignition switch to ON (II).
Replace the navigation unit (see page 23-155).
Refer to troubleshooting for no picture is
displayed (see page 23-119).
Di d t he i mage i mpr ov e?
Does t he nav i gat i on d i spl ay t ur n on?
08/08/21 14:07:26 61SNR030_230_0124
ProCarManuals.com
DYNOMITE -2009-

(#'#
)(#'#
)

µ
µ
µ
µ µ
µ
µ
µ
µ
µ
µ
µ
GPS icon is white or not shown Voice guidance cannot be heard, is broken
up, or there is static
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
YES
NO
23-12223-122Navigation System
Symptom Troubleshooting (cont’d)
NOTE:
 Check the vehicle battery condition first.
 Make sure the vehicle is parked outside and away from buildings.
 Refer to GPS Information (see page 23-142) for realtime satellite reception display.
 Check for window tinting above the GPS antenna and any non-OEM accessories mounted near the
navigation unit or GPS antenna.
1. Check for metallic window tint on the windshield and electronic aftermarket accessories (possibly
hidden) mounted near the GPS antenna or the
navigation unit.
Remove tint or the accessories, and
recheck.
Go to step 2.
2. Go into the Diagnostic Menu, and use the Navi System Link test (see page 23-136) to check the
GPS antenna.
Use the Navi ECU test under Unit Check
(see page 23-139) to check for a kinked, crushed, or
disconnected GPS antenna wire. If necessary, try a
known-good GPS antenna. If icon is still red,
replace the navigation unit (see page 23-155).
Check that nothing is blocking the GPS
antenna located behind the gauge assembly, and
recheck. Substitute a known-good navigation unit,
and recheck. NOTE:
 Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check that the volume setting and voice feedback are turned ON.
 Check the connectors for poor connection or loose terminals.
 Before troubleshooting, make sure you have the navigation system 4-digit anti-theft code.
 After troubleshooting, enter the navigation system anti-theft code.
1. Press the display unit SET-UP button.
2. Check the volume setting for the navigation system.
Set the volume to an audible level.
Go to step 3.
3. Check the radio operation.
Go to step 4.
Troubleshoot the audio system.
4. Go into the Diagnostic Menu, and use the Navi System Link test (see page 23-136) to check the
radio.
Troubleshoot the audio system.
Go to step 5.
5. Test the voice control switch (see page 23-156).
Replace the navigation unit (see page 23-155).
Replace the voice control switch (see page
23-157).
Is there metallic window tint or electronic accessor ies?
Is the GPS Ant icon red? Is it set to OFF?
Can y ou hear t he r ad i o?
Is the Radio icon red?I s v oi ce cont r ol sw i t ch OK ?
08/08/21 14:07:26 61SNR030_230_0125
ProCarManuals.com
DYNOMITE -2009-

Î
(#'#
)
 µ
µ
µ
µ
µ
µ
Voice control does not work/respond
YES
NO
YES
NO
YES
NO
23-123
NAVIGATION UNIT CONNECTOR D (5P) NAVI GUIDE (GRN)
NOTE: Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the connector for poor connection or loose terminals.
 Before troubleshooting, make sure you have the navigation system 4-digit anti-theft code.
 After troubleshooting, enter the navigation system anti-theft code.
Before assuming that a voice complaint is hardware
related, ensure that the voice control system is being
operated correctly.  Make sure you are on the correct screen when trying to issue a voice command. For instance, the
command ‘‘Find the nearest Italian Restaurant’’ only
works on a Map screen (See the Navigation System
Manual for a complete list of allowed voice
commands for the information being displayed.).
 Close the windows, moonroof, and doors.
 Set the fan speed to low (1 or 2).
 Adjust the air flow from the air conditioning vents so that they do not blow against the microphone on the
ceiling.
 Pause after pressing the navigation TALK button, then give a voice command clearly in a natural
speaking voice. If the system cannot recognize your
command, speak louder.
 If the microphone picks up voices other than yours, the system may not interpret your voice commands
correctly.
 If you speak a command with something in your mouth, or your voice is too husky, the system may
misunderstand your command.
 Compare the system operation with a known-good vehicle. Have more than one person test the system
operation. If the known-good vehicle performs the
same, it is a characteristic of the system. 1. Turn the ignition switch to ON (II).
2. Go into the Diagnostic Menu and use the Mic Level
test under Functional Setup (see page 23-147) to
check the operation of the navigation TALK and
navigation BACK buttons.
Go to step 10.
Go to step 3.
3. Turn the ignition switch to LOCK (0).
4. Do the voice control switch test (see page 23-156).
Go to step 5.
Replace the voice control switch.
5. Disconnect the cable reel 20P connector and navigation unit connector D (5P).
6. Check for continuity between body ground and navigation unit connector D (5P) terminal No. 4.
Repair short to body ground in the wire
between the navigation unit and the voice control
switch, or replace the cable reel.
Go to step 7.
(cont’d)
Wire side of female terminals
Ar e t he nav i gat i on T ALK and nav i gat i on BACKbut t ons oper at i onal ?
I s t he v oi ce cont r ol sw i t ch OK ?
Is there continuity?
08/08/21 14:07:26 61SNR030_230_0126
ProCarManuals.com
DYNOMITE -2009-

ÎÎ
µ
µµ µ
µ
µ
YES
NO YES
NO
YES
NO
23-124Navigation System
Symptom Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR D (5P)
CABLE REEL 20P CONNECTOR NAVI GUIDE (GRY)
NAVI GUIDE (GRN)
NAVIGATION UNIT CONNECTOR B (22P)
CABLE REEL 20P CONNECTORAUDIO REMOTE
GND (BRN)
AUDIO REMOTE
GND (BRN)
7. Check for continuity between navigation unitconnector D (5P) terminal No. 4 and cable reel 20P
connector terminal No. 8.
Go to step 8.
Repair open in the wire between the
navigation unit and the voice control switch, or
replace the cable reel. 8. Disconnect navigation unit connector B (22P).
9. Check for continuity between navigation unit
connector B (22P) terminal No. 6 and cable reel 20P
connector terminal No. 10.
Replace the navigation unit.
Repair open in the wire between the
navigation unit and the voice control switch, or
replace the cable reel.
10. Use the Mic Level dia gnostic under Functional
Setup (see page 23-147) to check the operation of
the microphone.
Check the operation of the voice control
system (see the Navigation System Manual).
Go to step 11.
11. Turn the ignition switch to LOCK (0).
12. Disconnect the microphone 3P connector (see page 23-157).
13. Disconnect navigation unit connector D (5P).
Wire side of female terminals
Terminal side of male terminals Wire side of female terminals
Terminal side of male terminals
Is there continuity? Is there continuity?
I s t he mi cr ophone oper at i onal ?
08/08/21 14:07:27 61SNR030_230_0127
ProCarManuals.com
DYNOMITE -2009-

´
(#'#
)

(#'#
)

µ
µ
µ
µ µ
µ
Display day/night mode does not work or
does not work properly System locks up or freezes constantly
YES
NO
YES
NO YES
NO
23-12823-128Navigation System
Symptom Troubleshooting (cont’d)
NOTE:
 Check the vehicle battery condition first.
 Check the connectors for poor connection or loose terminals.
 Before troubleshooting, get the navigation system anti-theft code.
 After troubleshooting, enter the navigation system anti-theft code.
 Full brightness on the instrument panel brightness control with the head lights turned on causes the
system to stay in the day mode, even when the lights
are on.
1. Make sure the instrument panel brightness control is not on full brightness. Turn the headlights on and
adjust the dash brightness to the middle range.
2. Change the day/night mode under Set-up to AUTO, and recheck.
The system is OK at this time.
Go to step 3.
3. Go into the Diagnostic Menu and use the Car Status test to check for an ILL signal (see page 23-141).
Replace the navigation unit (see page 23-155).
Check the ILL circuit between the
navigation unit and the No. 14 (7.5 A) fuse in the
under-dash fuse/relay box. NOTE:
 Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
1. Start the engine and turn the ignition switch to LOCK (0), then turn the ignition switch to ON (II).
The system is OK at this time.
Check the DVD for scratches or damage, and
the navigation unit for water damage. If OK, go into
the Diagnostic Menu and do all of the Unit Check
tests (see page 23-139). Also check for low battery
charge or poor charging system performance.
Does t he d i spl ay change t o d ay and ni ght mod es w hen t ur ni ng t he head l i ght s on and of f ?
I s t he I LL si gnal OK ? Does the system reboot?
08/08/21 14:07:28 61SNR030_230_0131
ProCarManuals.com
DYNOMITE -2009-

(#'#
)(#'#
)

µ
µ
µ
µ
µ
µ µ
µ
µ
µ
Navigation display stays on with ignition
switch in LOCK (0) Navigation cannot control audio system
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
23-12923-129
NOTE:
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, get the navigation system anti-theft code, then write down the audio presets.
 After troubleshooting, re-enter the anti-theft code, and re-initialize the navigation system, then enter the
audio presets.
 Check for aftermarket accessories that use the same power circuit. A feedback can cause this problem.
1. Remove the key from the ignition.
Go to step 2.
The system is OK at this time.
2. The vehicle may have been used as a demonstration vehicle at an event like an auto
show. In these events, power is often jumpered to
the navigation system so that the ignition key is not
needed in the vehicle. At the end of the show, the
jumper wire may not have been removed. Check
the navigation unit connector A (17P) for a non-
factory jumper wire in series with the factory cable.
Remove the jumper wire, and re-test. Return
the jumper wire to Tech Line.
Go to step 3.
3. Check if the audio unit works.
Troubleshoot the ACC circuit for a short to
power with another circuit.
Replace the navigation unit (see page 23-155). NOTE:
 Check the vehicle battery condition first.
 Verify that the correct navigation unit is installed for this model. Go into the Diagnostic mode and use
Version (see page 23-149).
 Check for connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have anti- theft codes for the navigation system.
 After troubleshooting, enter the anti-theft codes for the navigation system.
 Make sure that the correct navigation DVD color and version are installed.
 Inspect the navigation DVD for dirt or damage.
 Check any official Honda service website for more service information about the navigation system.
1. Make sure the anti-theft code for the navigation system is entered.
2. Go into the Diagnostic Menu and use the Navi System Link test (see page 23-136).
Do the troubleshooting for the voice
guidance cannot be heard (see page 23-122).
Go to step 3.
3. Substitute a known-good navigation unit (see page 23-155), and recheck.
Replace the navigation unit (see page 23-155).
Do the audio system troubleshooting.
Does t he nav i gat i on scr een st ay on?
Is t her e a j umper w i r e?Does the audio unit work with the ignition switchoff? Is the Radio icon red?
Can t he nav i gat i on cont r ol aud i o?
08/08/21 14:07:28 61SNR030_230_0132
ProCarManuals.com
DYNOMITE -2009-

Î

Navi System Link
23-136Navigation System
System Diagnostic Mode (cont’d)
Navi System Link
Navi.ECUReturn
Exit Diag
Detecting..
GPS Ant.
Display Radio BACK
Air-Con
 This diagnostic step tests the cables connecting the
navigation components. Ensure that the ignition
switch is in the ON (II) position. When the diagnosis
begins, you hear a bong sound. The system is in a
Detecting mode, and is waiting for all the items in
white to be tested. This includes the voice control
switch (navigation TALK/BACK buttons), and the
microphone. Press the navigation TALK button on the
steering wheel, and in a normal voice, say ‘‘testing’’.
The Talk indicator on the screen should turn green,
and the voice level indicator should move to at least
the 6th bar to pass. Next, press the navigation BACK
button. The Cancel indicator should turn green.
 If all of the communication lines connecting the system components, and the navigation TALK/BACK
buttons/microphone check out OK (all block diagram
items green), then the OK indicator turns green.
 If there is a problem with the system, the faulty system component item turns red, and the screen
shows NG in red. Use the troubleshooting index, and
other diagnostic screens to help locate the problem.
 The indicator on the screen may not change until you cycle the ignition switch. After repairing the affected
cable or system, repeat this diagnostic.
NOTE: Green boxes and green OK indicate that the
communications lines (cables) are intact. This
diagnostic does not necessarily imply that the
individual components are functioning properly. For
instance, the GPS antenna wire may be crushed, but
still show as green. A road test, or other diagnostic
maybenecessarytofindtheproblem.  Select Return to return to the Diagnostic Menu, or the
Exit Diag button to exit.
NOTE: The Mic Level indicator must reach the 6th bar
or greater to pass the test.
08/08/21 14:07:29 61SNR030_230_0139
ProCarManuals.com
DYNOMITE -2009-