2005 TOYOTA AVENSIS reset

D30865
C91925
−
AUTOMATIC TRANSMISSION / TRANS TRANSMISSION VALVE BODY ASSY (U151E)
40−23
AVENSIS Supplement (RM1045E)
10. I NSTALL AUTO M AT I C TRANSAXLE O I L PAN
SUB −ASSY
(a) Install the 2 magnets to the oil pan.
(b) Apply seal packing to the 18 bolts. Seal packing:
THREE BOND 1344 or equivalent
(c) Install a new gasket, the oil pan and 18 bolts to the trans- axle case.
Torque: 7.8 N
m (80 kgf
cm, 69 in.
lbf)
NOTICE:
Apply seal packing to the bolts and tighten them within 10
minutes of application.
11 . ADD AUTOMATIC TRANSAXLE FLUID (SEE PUB. NO. RM 1018E, PAGE 40 −2)
1 2. INSPECT AUTOMATIC TRANSAXLE FLUID (SEE PUB. NO. RM 1018E, PAGE 40 −2)
1 3. RESET MEMORY (SEE PAGE 05 −54 1)

C91925
40−1 8
−
AUTOMATIC TRANSMISSION / TRANS TRANSMISSION WIRE (U151E)
AVENSIS Supplement (RM1045E)
(c) Install a new gasket, the oil pan and 18 bolts to the trans- axle case.
Torque: 7.8 N
m (80 kgf
cm, 69 in.
lbf)
NOTICE:
Apply seal packing to the bolts and tighten them within 10
minutes of application.
9. ADD AUTOMATIC TRANSAXLE FLUID (SEE PUB. NO. RM 1018E, PAGE 40 −2)
1 0. INSPECT AUTOMATIC TRANSAXLE FLUID (SEE PUB. NO. RM 1018E, PAGE 40 −2)
11 . RESET MEMORY (SEE PAGE 05 −54 1)

05KAS–02
– DIAGNOSTICSELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U341E) (From February, 2004)05–225
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
INITIALIZATION
1. RESET MEMORY
CAUTION:
Perform the RESET MEMORY (AT initialization) when replacing the automatic transaxle assy, engine
assy or ECM.
NOTICE:
Intelligent tester II only
HINT:
The ECM memorizes the condition that the ECT controls the automatic transaxle assy and engine assy ac-
cording to those characteristics. Therefore, when the automatic transaxle assy, engine assy, or ECM has
been replaced, it is necessary to reset the memory so that the ECM can memorize the new information.
Reset procedure is as follows.
(a) Turn the ignition switch off.
(b) Connect the intelligent tester II to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Turn the intelligent tester II main switch on.
(e) Perform the reset memory procedure from the main menu.

G30843
05–226–
DIAGNOSTICS ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] (U341E) (From February, 2004)
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
CAUTION:
After performing the RESET MEMORY, be sure to perform the ROAD TEST ( see page 05–219) de-
scribed earlier.
HINT:
The ECM is learned by performing the ROAD TEST.

I42014(3)(1)
I42013
(5)
(1) 05–312
– DIAGNOSTICSCRUISE CONTROL SYSTEM (2AZ–FSE)(From
February, 2004)
AVENSIS REPAIR MANUAL SUPPLEMENT
(RM1098E)
(d) Inspect the CANCEL function.
(1) Push the ON–OFF button on.
(2) Drive at the required speed (40 km/h (25 mph) or
higher).
(3) Push down the cruise control main switch to SET/
COAST.
(4) When doing one of the following, check that the
cruise control system is cancelled and that the nor-
mal driving mode is reset.
Depressing the brake pedal
Shifting into any position except D while driv-
ing
Pushing the ON–OFF button off
Pulling the cruise control main switch to CAN-
CEL
(e) Inspect the RES (RESUME) function.
(1) Push the ON–OFF button on.
(2) Drive at the required speed (40 km/h (25 mph) or
higher).
(3) Push down the cruise control main switch to SET/
COAST.
(4) When doing one of the following, check that the
cruise control system is cancelled and that the nor-
mal driving mode is reset.
Depressing the brake pedal
Shifting into any position except D while driv-
ing
Pulling the cruise control main switch to CAN-
CEL
(5) After pushing up the cruise control main switch to
RES/ACC at a driving speed of more than 40 km/h
(25 mph), check that the vehicle restores the speed
prior to the cancellation.