2005 TOYOTA AVENSIS reset

05±1454
± DIAGNOSTICSNAVIGATION SYSTEM
AVENSIS REPAIR MANUAL (RM1018E) DTCCountermeasure and inspected parts Condition Diagnosis item
DE
*3Slave Reset (Momentary Interruption)After engine start, slave component has
been disconnected.
Check harness for power supply system of
component shown by sub±code.

Check harness for communication system
of component shown by sub±code.
DF
*5Master ErrorDue to defective condition of component
with a display, master function is switched to
audio equipment.
Error occurs in communication between
sub±master (audio) and master component.
Check harness for power supply of multi±
display (CRT display) display.

Check harness for communication system
of multi±display (CRT display) display.
E0
*1Registration Completion Instruction ErrorºRegistration Completion Instructionº com-
mand from master cannot be received.Since this DTC is provided for engineering
purpose, it may be detected when no actual
failure exists.
E1
*1Audio processor ON errorWhile source equipment is operating, AMP
output is stopped.
Check harness for power supply of radio
receiver assy.

Check harness for communication system
of radio receiver assy.
E2ON/OFF Instruction Parameter ErrorError occurs in ON/OFF controlling com-
mand from multi±display (CRT display) dis-
play.Replace multi±display (CRT display) display.
E3
*1Registration Request TransmissionRegistration Request command is output
from slave component.
Receiving Connection Check Instruction,
Registration Request command is output
from sub±master component.Since this DTC is provided for engineering
purpose, it may be detected when no actual
failure exists.
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.Since this DTC is provided for engineering
purpose, it may be detected when no actual
failure exists.
(b) Logical address: 21 (Switch)
DTCDiagnosis itemConditionCountermeasure and inspected parts
10Panel Switch ErrorError in panel switch input part is detected.
(Error in switch control part, or internal com-
munication error with switch control part is
detected.)
Inspect all switches on panel switch test
screen in display check mode. If any of
them does not function, replace radio re-
ceiver assy.

If all switches function without problem, ob-
serve them for a while.
11Touch Switch ErrorError in touch switch sensor is detected.
(Light level of LED is detected to be less
than a fixed value.)
Inspect all touch switches on touch switch
test screen in display check mode. If any
of lines do not react, replace radio receiver
assy.

If all of vertical and horizontal lines react
normally, observe them for a while.
(c) Logical address: 61 (Cassette tape player's switch)
DTCDiagnosis itemConditionCountermeasure and inspected parts
40Mechanical Error of MediaMalfunction due to mechanical failure is
identified.
Or cassette tape is cut or entangled.
Inspect cassette tape.

Replace radio receiver assy.
(d) Logical address: 62 (CD player)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
42No Disc ReadoutDisc cannot be read.
Inspect CD.

Replace radio receiver assy.
44CD player ErrorError is detected in CD player.Replace radio receiver assy.
45EJECT ErrorMagazine cannot be ejected.Replace radio receiver assy.
46Scratched/Reversed DiscScratches or dirt is found on CD surface or
CD is set upside down.Inspect CD.

± DIAGNOSTICSNAVIGATION SYSTEM
05±1455
AVENSIS REPAIR MANUAL (RM1018E) DTCCountermeasure and inspected parts Diagnosis content Diagnosis item
47CD Player Temp. Too High
Readout cannot be done because tempera-
ture around player's pick±up (reading part)
is too high.
With IG switch OFF, leave vehicle in cool
shaded place for a while and recheck.
After deleting the DTC memory, if same
code is detected, replace radio receiver
assy.
48CD Player Excess CurrentExcess current is applied radio receiver
assy.Replace radio receiver assy.
2. NAVIGATION ECU (Physical address: 178)
HINT:

*1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage
for starting the engine.

*2: This code is stored in 210 seconds after the master component is turned off with the ignition switch
ACC or ON.

*3: This code may be stored when the ignition switch is turned in 1 min. again after engine start.

*4: This code may be stored when the ignition switch is turned again after engine start.
(a) Logical address: 01 (Communication control)
DTCDiagnosis itemConditionCountermeasure and inspected parts
D6
*1Absence of MasterComponent in which this code is recorded
has been disconnected from system with
ignition switch ACC or ON. Or, when this
code was recorded, multi±display (CRT dis-
play) display was disconnected.
Check harness for power supply system of
multi±display (CRT display) display.

Check harness for communication system
of multi±display (CRT display) display.

Check harness for power supply system of
navigation ECU.

Check harness for communication system
of navigation ECU.
D7
*2Connection Check ErrorComponent in which this code is recorded
has been disconnected from system with
ignition switch ACC or ON. Or, when this
code was recorded, multi±display (CRT dis-
play) display was disconnected.
Check harness for power supply system of
multi±display (CRT display) display.

Check harness for communication system
of multi±display (CRT display) display.

Check harness for power supply system of
navigation ECU.

Check harness for communication system
of navigation ECU.
DC
*3Transmission ErrorTransmission to component shown by sub±
code has been failed.
(This code does not necessarily mean actu-
al failure.)If same sub±code is recorded in other com-
ponent(s), check harness for power supply
and communication system of all compo-
nents shown by code.
DD
*4Master Reset (Momentary Interruption)Component that is to be master has been
disconnected after engine start.
Check harness for power supply system of
multi±display (CRT display) display.

Check harness for communication system
of multi±display (CRT display) display.

If error occurs frequently, replace multi±
display (CRT display) display.
E0
*1Registration Completion Instruction ErrorºRegistration Completion Instructionº com-
mand from master cannot be received.Since this DTC is provided for engineering,
it may be detected when no actual failure
exists.
E2ON/OFF Instruction Parameter ErrorError is detected in ON/OFF control com-
mand from multi±display (CRT display) dis-
play .Replace multi±display (CRT display) display.
E3
*1Registration Request Transmission
Registration Request command is output
from slave component.

Registration Request command is output
from sub±master component.Since this DTC is provided for engineering,
it may be detected when no actual failure
exists.

± DIAGNOSTICSNAVIGATION SYSTEM
05±1457
AVENSIS REPAIR MANUAL (RM1018E) DTCCountermeasure and inspected parts Diagnosis content Diagnosis item
D9
*1Last Mode ErrorComponent operated (sound and/or image
was provided) before engine stop is or was
disconnected with ignition switch ACC or
ON.
Check harness for power supply of compo-
nent shown by sub±code.

Check harness for communication system
of component shown by sub±code.
DB
*1Mode Status ErrorDual alarm is detected.
Check harness for power supply system of
component shown by sub±auxiliary code.

Check harness for communication system
of component shown by sub±code.
DC
*4Transmission ErrorTransmission to component shown by auxil-
iary code has been failed.
(This code does not necessarily mean actu-
al failure.)If same auxiliary code is recorded in order
component(s), check harness for power
supply and communication system of all
components shown by code.
DE
*3Slave Reset (Momentary Interruption)After engine start, slave component has
been disconnected.
DB
Check harness for power supply system of
component shown by sub±code.

Check harness for communication system
of component shown by sub±code.
E2ON/OFF Instruction Parameter ErrorError is detected in ON/OFF control com-
mand from radio receiver assy.Replace radio receiver assy.
E3
*1Registration Request Transmission
Registration Request command is output
from slave component.

By reception of connection check instruc-
tion, Registration Request command is out-
put from sub±master component.Since this DTC is provided for engineering,
it may be detected when no actual failure
exists.
(b) Logical address: 21 (Switch)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
10Panel Switch ErrorError in panel switch input part is detected.
(Error in switch control part, or internal com-
munication error with switch control part is
detected.)
Inspect all switches on panel switch test
screen in display check mode. If any of
them do not function, replace multi±display
(CRT display) display.

If all switches function without problem, ob-
serve them for a while.
11Touch Switch ErrorError in touch switch sensor is detected.
(Light level of LED is detected to be less
than a fixed value.)
Inspect all touch switches on touch switch
test screen in display check mode. If any
of lines does not react, replace multi±dis-
play (CRT display) display.

If all of vertical and horizontal lines react
normally, observe them for a while.
(c) Logical address: 34 (Front passenger monitor)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
10Error in Picture CircuitError in power supply system for picture cir-
cuit (abnormal voltage) is detected.Replace multi±display (CRT display) display.
11Back±light Error (No current)Decline in power output from inverter circuit
for back±light.Replace multi±display (CRT display) display.
12Back±light Error (Excess current)Excess power output from inverter circuit for
back±light.Replace multi±display (CRT display) display.

05±1458
± DIAGNOSTICSNAVIGATION SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
4. BODY ECU (COMBINATION METER) (Physical address: 1EC)
HINT:

*1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for
starting an engine.

*2: It may be stored when the ignition switch is turned in 1 min. again after the engine starts.

*3: It may be stored when the ignition switch is turned again after the engine starts.

*4: This code is stored in 210 sec. after the master components is turned off with the ignition switch
ACC or ON.
Logical address: 01 (Communication control)
DTCDiagnosis itemDiagnosis contentCountermeasure and inspected parts
D6
*1Absence of MasterComponent in which this code is recorded
has been disconnected from system with
ignition ACC or ON. Or, when this code was
recorded, multi±display (CRT display) dis-
play was disconnected.
Check harness for power supply of multi±
display (CRT display) display.

Check harness for communication system
of multi±display (CRT display) display.

Check harness for power supply of body
ECU.

Check harness for communication system
of body ECU.
D7Communication Check ErrorComponent in which this code is recorded is
or was disconnected from system after en-
gine start. Or, when recording this code,
multi±display (CRT display) display was dis-
connected.
Check harness for power supply of multi±
display (CRT display) display.

Check harness for communication system
of multi±display (CRT display) display.

Check harness for power supply of body
ECU.

Check harness for communication system
of body ECU.
DC
*2Transmission ErrorTransmission to component shown by auxil-
iary code has been failed.
(Detecting this DTC does not necessarily
mean actual failure.)If same auxiliary code is recorded in other
components, check harness for power sup-
ply and communication system of all compo-
nents shown by code.
DD
*3Master Reset (Momentary Interruption)After engine was started, multi±display
(CRT display) display was disconnected
from system
Check harness for power supply of multi±
display (CRT display) display.

Check harness for communication system
of multi±display (CRT display) display.

If this error occurs frequently, replace mul-
ti±display (CRT display) display.
DF
*4Master ErrorDue to defective condition of component
with a display, master function is switched to
audio equipment.
Error occurs in communication between
sub±master (audio) and master component.
Check harness for power supply of radio
receiver assy.

Check harness for communication system
of multi±display (CRT display) display.

Check harness for communication system
between radio receiver assy and multi±dis-
play (CRT display) display.
E0
*1Registration Completion Instruction ErrorºRegistration Completion Instructionº com-
mand from master cannot be received.Since this DTC is provided for engineering
purpose, it may be detected when no actual
failure exists.
E1
*1Audio processor ON errorWhile source equipment is operating, AMP
output is stopped.
Check harness for power supply of multi±
display (CRT display) display.

Check harness for communication system
of multi±display (CRT display) display.

40±54
±
AUTOMATIC TRANSMISSION / TRANS TRANSMISSION WIRE (U241E)
AVENSIS REPAIR MANUAL (RM1018E)
9. ADD AUTOMATIC TRANSAXLE FLUID
10.INSPECT AUTOMATIC TRANSAXLE FLUID (See page 40±2)
11. RESET MEMORY
(a)1AZ±FE (See pege 05±863)
(b)1AZ±FSE (See pege 05±920)

40122±01
C62929
D25376
C62929
±
AUTOMATIC TRANSMISSION / TRANS TRANSMISSION WIRE (U341E)
40±51
AVENSIS REPAIR MANUAL (RM1018E)
TRANSMISSION WIRE (U341E)
REPLACEMENT
1.REMOVE TRANSMISSION VALVE BODY ASSY (See page 40±42)
2. REMOVE TRANSMISSION WIRE
(a) Removal the bolt and transmission wire.
3. INSTALL TRANSMISSION WIRE
(a) Coat an O±ring with ATF.
(b) Install the transmission wire.
(c) Install the bolt.Torque: 5.4 N
m (55 kgf
cm, 48 in.
lbf)
4.INSTALL TRANSMISSION VALVE BODY ASSY (See page 40±42)
5.RESET MEMORY (See page 05±985)

D25591
D25674
Magnet
C83111
40±50
±
AUTOMATIC TRANSMISSION / TRANS TRANSMISSION VALVE BODY ASSY (U241E)
AVENSIS REPAIR MANUAL (RM1018E)
9. INSTALL TRANSMISSION WIRE
(a) Coat an O±ring with ATF.
(b) Install the ATF temperature sensor with the lock plate and bolt.
Torque: 6.6 N
m (67 kgf
cm, 58 in.
lbf)
(c) Connect the 5 solenoid valve connectors.
10. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB±ASSY
(a) Install the 2 magnets in the oil pan.
(b) Apply the seal packing or equivalent to the 18 bolts. Seal packing:
THREE BOND 1344 or equivalent
(c) Install a new gasket and the oil pan to the transaxle case with the 18 bolts.
Torque: 7.8 N
m (80 kgf
cm, 69 in.
lbf)
NOTICE:
Apply the seal packing or equivalent to the bolts and tight-
en them within 10 minutes after application because the
bolts should be seal bolts.
11. ADD AUTOMATIC TRANSAXLE FLUID
12.INSPECT AUTOMATIC TRANSAXLE FLUID (See page 40±2)
13. RESET MEMORY
(a)1AZ±FE (See pege 05±863)
(b)1AZ±FSE (See pege 05±920)

D08009
40±46
±
AUTOMATIC TRANSMISSION / TRANS TRANSMISSION VALVE BODY ASSY(U341E)
AVENSIS REPAIR MANUAL (RM1018E)
(c)Install the oil pan and a new gasket with the 19 bolts. Torque: 7.8 N
m (80 kgf
cm, 69 in.
lbf)
9.ADD AUTOMATIC TRANSAXLE FLUID
10.INSPECT AUTOMATIC TRANSAXLE FLUID (See page 40±2)
11.RESET MEMORY (See page 05±985)