2005 TOYOTA AVENSIS heater

A79112
E1OX B2S1 H9
+B
HT Heated Oxygen Sensor
Component Side:
Front View
A62378
+BHT
E1
1
2
3 4
OX
B1S1 H7
Heated Oxygen Sensor Component Side:
Front View B1S2 H8
B2S2H10
B16200
− DIAGNOSTICSSFI SYSTEM (2AZ−FSE)
05−51
AVENSIS Supplement (RM1045E)
1INSPECT HEATED OXYGEN SENSOR(HEATER RESISTANCE)
(a) Disconnect the H7, H8, H9 or H10 heated oxygen sensor
connector.
(b) Measure the resistance between the terminals of the
heated oxygen sensor connector.
Standard (Bank 2 sensor1):
Tester ConnectionResistance
1(HT)−2 (+B)11to16
at 20_C (68_F)
1(HT)−4(E1)10k
or higher
Standard (Except Bank 2 sensor1):
Tester ConnectionResistance
1(HT)−2 (+B)11to16
at 20_C (68_F)
1(HT)−4(E1)10k
or higher
(c) Reconnect the heated oxygen sensor connector.
NG REPLACE HEATED OXYGEN SENSOR
OK
2 INSPECT EFI RELAY
(a) Remove the EFI relay from the engine room R/B No. 4.
(b) Check for continuity in the EFI relay.
Standard:
Tester ConnectionSpecified Condition
1−2Continuity
3−5No continuity
3−5Continuity
(Apply battery voltage to terminals1and 2)
(c) Reinstall the EFI relay.
NG REPLACE EFI RELAY
OK

05CID−02
−
DIAGNOSTICS SFI SYSTEM (2AZ−FSE)
05 −31
AVENSIS Supplement (RM 1045E)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may be different than your readings depending on the type of instrument used
and other factors.
During the DTC check, refer to the table below if a malfunction code is displayed. For details about each
code, refer to the page number in the DTC Chart’s left column.
DTC No.
(See Page)Detection ItemTrouble Area*1
CHK ENGMemory
P00 10
(05 −41)Camshaft Position ”A” Actuator
Circuit (Bank 1)SOpen or short in OCV circuit
S OCV
S ECM
ff
P00 11
(05 −44)Camshaft Position ”A” −Timing
Over −Advanced or System Per-
formance (Bank 1)SValve timing
S OCV
S Camshaft timing gear assy
S ECM
ff
P00 12
(05 −41)Camshaft Position ”A” −Timing
Over −Retarded (Bank 1)
SValve timing
S OCV
S Camshaft timing gear assy
S ECM
ff
P00 16
(05 −48)Crankshaft Position −Camshaft
Position Correlation (Bank 1
Sensor A)S Mechanical system (Timing chain has jumped a tooth, chain
stretched)
S ECM
ff
P003 1
(05 −49)Oxygen Sensor Heater Circuit
Low (Bank 1Sensor 1)*7
SOpen or short in heater circuit of heated oxygen sensor
S Heated oxygen sensor heater (Bank 1Sensor 1)*7
SEFI relay
S EFI No. 2 fuse
S ECMff
P0032
(05 −49)Oxygen Sensor Heater Circuit
High (Bank 1Sensor 1)*7
SOpen or short in heater circuit of heated oxygen sensor
S Heated oxygen sensor heater (Bank 1Sensor 1)*7
SEFI relay
S ECMff
P0037
(05 −49)Oxygen Sensor Heater Control
Circuit Low (Bank 1Sensor 2) *7
SOpen in heater circuit of heated oxygen sensor
S Heated oxygen sensor heater (Bank 1Sensor 2) *7
SEFI relay
S EFI No. 2 fuse
S ECMff
P0038
(05 −49)Oxygen Sensor Heater Control
Circuit High (Bank 1Sensor 2) *7
SShort in heater circuit of heated oxygen sensor
S Heated oxygen sensor heater (Bank 1Sensor 2) *7
SEFI relay
S ECMff
P005 1
(05 −49)Oxygen Sensor Heater Circuit
Low (Bank 2 Sensor 1)*8
SOpen in heater circuit of heated oxygen sensor
S Heated oxygen sensor heater (Bank 2 Sensor 1)*8
SEFI relay
S EFI No. 2 fuse
S ECMff
P0052
(05 −49)Oxygen Sensor Heater Circuit
High (Bank 2 Sensor 1)*8
SShort in heater circuit of heated oxygen sensor
S Heated oxygen sensor heater (Bank 2 Sensor 1)*8
SEFI relay
S ECMff
P0057
(05 −49)Oxygen Sensor Heater Control
Circuit Low (Bank 2 Sensor 2) *8
SOpen in heater circuit of heated oxygen sensor
S Heated oxygen sensor heater (Bank 2 Sensor 2) *8
SEFI relay
S EFI No. 2 fuse
S ECMff
P0058
(05 −49)Oxygen Sensor Heater Control
Circuit High (Bank 2 Sensor 2) *8
SShort in heater circuit of heated oxygen sensor
S Heated oxygen sensor heater (Bank 2 Sensor 2) *8
SEFI relay
S ECMff

−
DIAGNOSTICS SFI SYSTEM (2AZ−FSE)
05 −33
AVENSIS Supplement (RM 1045E)
DTC No.
(See Page) Memory
*
1
CHK ENG
Trouble Area
Detection Item
P0 130 *3
(05 −82)
Oxygen Sensor Circuit (Bank 1
Sensor 1)*7
SOpen or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 1Sensor 1)*7
SHeated oxygen sensor heater (Bank 1Sensor 1)*7
SEFI relay
S Air induction system
S Fuel pressure
S Injector
S ECMff
P0 133 *3
(05 −94)
Oxygen Sensor Circuit Slow Re-
sponse (Bank 1Sensor 1)*7
SOpen or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 1Sensor 1)*7
SHeated oxygen sensor heater (Bank 1Sensor 1)*7
SEFI relay
S Air induction system
S Fuel pressure
S Injector
S ECMff
P0 134
(05 −1 01)Oxygen Sensor Circuit No Activ-
ity Detected
(Bank 1Sensor 1)*
7
SOpen or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 1Sensor 1)*7
SHeated oxygen sensor heater (Bank 1Sensor 1)*7
SEFI relay
S Air induction system
S Fuel pressure
S PCV hose connection
S PCV valve and hose
S Injector
S Gas leakage in exhaust system
S ECM
ff
P0 136 *3
(05 −1 09)
Oxygen Sensor Circuit Malfunc-
tion (Bank 1Sensor 2) *7
SOpen or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 1Sensor 2) *7
SHeated oxygen sensor heater (Bank 1Sensor 2) *7
SEFI relay
ff
P0 150 *3
(05 −82)
Oxygen Sensor Circuit (Bank 2
Sensor 1)*8
SOpen or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 2 Sensor 1)*8
SHeated oxygen sensor heater (Bank 2 Sensor 1)*8
SEFI relay
S Air induction system
S Fuel pressure
S Injector
S ECMff
P0 153 *3
(05 −94)
Oxygen Sensor Circuit Slow Re-
sponse (Bank 2 Sensor 1)*8
SOpen or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 2 Sensor 1)*8
SHeated oxygen sensor heater (Bank 2 Sensor 1)*8
SEFI relay
S Air induction system
S Fuel pressure
S Injector
S ECMff
P0 154
(05 −1 01)Oxygen Sensor Circuit No Activ-
ity Detected
(Bank 2 Sensor 1)*
8
SOpen or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 2 Sensor 1)*8
SHeated oxygen sensor heater (Bank 2 Sensor 1)*8
SEFI relay
S Air induction system
S Fuel pressure
S PCV hose connection
S PCV valve and hose
S Injector
S Gas leakage in exhaust system
S ECM
ff

05−34
−
DIAGNOSTICS SFI SYSTEM (2AZ−FSE)
AVENSIS Supplement (RM 1045E)
DTC No.
(See Page) Memory
*
1
CHK ENG
Trouble Area
Detection Item
P0 156 *3
(05 −1 09)
Oxygen Sensor Circuit Malfunc-
tion (Bank 2 Sensor 2) *8
SOpen or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 2 Sensor 2) *8
SHeated oxygen sensor heater (Bank 2 Sensor 2) *8
SEFI relay
ff
P0 171 *3
(05 −11 5)System too Lean (Bank 1)*7
SAir induction system
S Injector blockage
S Mass air flow meter
S Manifold absolute pressure sensor
S Engine coolant temperature sensor
S Fuel pressure
S Gas leakage in exhaust system
S Open or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 1Sensor 1)*
7
SHeated oxygen sensor heater (Bank 1Sensor 1)*7
SEFI relay
S PCV valve and hose
S PCV hose connection
S ECM
ff
P0 172 *3
(05 −11 5)System too Rich (Bank 1)*7
SInjector leakage or blockage
S Mass air flow meter
S Manifold absolute pressure sensor
S Engine coolant temperature sensor
S Ignition system
S Fuel pressure
S Gas leakage in exhaust system
S Open or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 1Sensor 1)*
7
SECM
ff
P0 174 *3
(05 −11 5)System too Lean (Bank2) *8
SAir induction system
S Injector blockage
S Mass air flow meter
S Manifold absolute pressure sensor
S Engine coolant temperature sensor
S Fuel pressure
S Gas leakage in exhaust system
S Open or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 2 Sensor 1)*
8
SHeated oxygen sensor heater (Bank 2 Sensor 1)*8
SEFI relay
S PCV valve and hose
S PCV hose connection
S ECM
ff
P0 175 *3
(05 −11 5)System too Rich (Bank2) *8
SInjector leakage or blockage
S Mass air flow meter
S Manifold absolute pressure sensor
S Engine coolant temperature sensor
S Ignition system
S Fuel pressure
S Gas leakage in exhaust system
S Open or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 2 Sensor 1)*
8
SECM
ff
P0 190
(05 −1 27)Fuel Rail Pressure Sensor Cir-
cuitSOpen or short in fuel pressure sensor circuit
S Fuel pressure sensor
S ECM
ff

05−40
−
DIAGNOSTICS SFI SYSTEM (2AZ−FSE)
AVENSIS Supplement (RM 1045E)
DTC No.
(See Page) Memory
*
1
CHK ENG
Trouble Area
Detection Item
P2 138
(05 −224)Throttle Pedal Position Sensor/
Switch ”D”/”E” Voltage Correla-
tionSVPA and VPA2 circuits are short −circuit
S Accelerator pedal position sensor
S ECM
ff
P2 195 *3
(05 −82)
Oxygen Sensor Signal Stuck
Lean (Bank 1Sensor 1)*7
SOpen or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 1Sensor 1)*7
SHeated oxygen sensor heater (Bank 1Sensor 1)*7
SEFI relay
S Air induction system
S Fuel pressure
S Injector
S ECMff
P2 196 *3
(05 −82)
Oxygen Sensor Signal Stuck
Rich (Bank 1Sensor 1)*7
SOpen or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 1Sensor 1)*7
SHeated oxygen sensor heater (Bank 1Sensor 1)*7
SEFI relay
S Air induction system
S Fuel pressure
S Injector
S ECMff
P2 197 *3
(05 −82)
Oxygen Sensor Signal Stuck
Lean (Bank 2 Sensor 1)*8
SOpen or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 2 Sensor 1)*8
SHeated oxygen sensor heater (Bank 2 Sensor 1)*8
SEFI relay
S Air induction system
S Fuel pressure
S Injector
S ECMff
P2 198 *3
(05 −82)
Oxygen Sensor Signal Stuck
Rich (Bank 2 Sensor 1)*8
SOpen or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 2 Sensor 1)*8
SHeated oxygen sensor heater (Bank 2 Sensor 1)*8
SEFI relay
S Air induction system
S Fuel pressure
S Injector
S ECMff
P27 16*4
(05 −622)
Pressure Control Solenoid ”D”
ElectricalSElectronic controlled automatic transmission (ECT)ff
B2799
(*6)Engine Immobilizer System Mal-
functionSImmobilizer system
f
*1:
CHK ENG (Check engine warning light) dese not illuminate,f CHK ENG (Check engine warning
light) illuminates.
*
2: CHK ENG (Check engine warning light) illuminates or blinks.
*
3: For Euro −OBD vehicles only.
*
4: For A/T only.
*
5: See page 05 −1714 of Pub. No. RM 1018E AVENSIS.
*
6: See page 05 −1628 of Pub. No. RM 1018E AVENSIS.
*
7: Bank 1refers to the No. 1and No. 4 cylinders.
*
8: Bank 2 refers to the No. 2 and No. 3 cylinders.

−
DIAGNOSTICS SFI SYSTEM (2AZ−FSE)
05 −1 3
AVENSIS Supplement (RM 1045E)
Symbols (Terminals No.)
STD Voltage
Condition
Terminal Description
Wiring Color
VCP2 (E9 −27) −EPA2 (E9 −29)B −Y
Power source of acceler-
ator pedal position sensor
(for VPA2)
Ignition switch ON4.5 to 5.5 V
VG (E 13− 30) −EVG (E 13− 29)L− Y −GMass air flow meterIdling, P or N position, A/C switch
OFF0.5 to 3.0 V
THA (E 13− 20) −E2 (E 13− 28)GR −BRIntake air temperature
sensorIdling, Intake air temperature 20 ˚C
(68 ˚F)0.5 to 3.4 V
THW (E 13−1 9)−E2 (E 13− 28)B −W −BREngine coolant tempera-
ture sensorIdling, Coolant temperature 80 ˚C
(176˚F)0.2 to 1.0 V
#1 (E 13−1 )− E0 1(E 13− 7)
#2 (E 13− 2) −E0 1(E 13− 7)
#3 (E 13− 3) −E0 1(E 13− 7)
#4 (E 13− 4) −E0 1(E 13− 7)G −W −W −B
W −R −W −B
R −W −W −B
W −L − W −B
InjectorIgnition switch ON9to 14V
#1 (E 13−1 )− E0 1(E 13− 7)
#2 (E 13− 2) −E0 1(E 13− 7)
#3 (E 13− 3) −E0 1(E 13− 7)
#4 (E 13− 4) −E0 1(E 13− 7)G −W −W −B
W −R −W −B
R −W −W −B
W −L − W −B
InjectorIdlingPulse generation
(See page 05 −1 36)
IJF 1(E 13− 25) −E0 1(E 13− 7)R −B −W −BInjectorIdlingPulse generation
(See page 05 −1 36)
IGT 1(E 13− 8) −E1 (E 11−1 )
IGT2 (E 13− 9) −E1 (E 11−1 )
IGT3 (E 13−1 0)−E1 (E 11−1 )
IGT4 (E 13−11 )− E1 (E 11−1 )R−W −BR
P −BR
LG −B −BR
L − Y −BR
Ignition coil with igniter
(ignition signal)IdlingPulse generation
(See page 05 −1 67)
IGF 1(E 13− 24) −E1 (E 11−1 )W−R −BR
Ignition coil with igniter
(ignition confirmation sig-
nal)
Ignition switch ON4.5 to 5.5 V
IGF 1(E 13− 24) −E1 (E 11−1 )W−R −BR
Ignition coil with igniter
(ignition confirmation sig-
nal)
IdlingPulse generation
(See page 05 −1 67)
G2+ (E 11 −27) −NE −(E 11 − 24)W−RCamshaft position sensorIdlingPulse generation
(See page 05 −1 64)
NE+ (E 11 −25) −NE −(E 11 − 24)G−RCrankshaft position sen-
sorIdlingPulse generation
(See page 05 −1 60)
FPR (E 12− 7) −E0 1(E 13− 7)LG −BRFuel pump relayIgnition switch ON0−3.0 V
FC (E9 −10)−E1 (E 11−1 )G−Y −BRFuel pump controlIgnition switch ON9to 14V
M+ (E 11 −3)−ME0 1(E 11 − 4)
M − (E 11 − 2)−ME0 1(E 11 − 4)B−W −B
W −W −BThrottle motorIdlingPulse generation
OX 1A(E 12− 22) −E2 (E 13− 28)B −BRHeated oxygen sensorMaintain engine speed at 2,500 rpm
for 2 minutes after warming upPulse generation
(See page 05 −82)
OX 1B(E 12− 21)
− O1B − (E 11 − 26)B−WHeated oxygen sensorMaintain engine speed at 2,500 rpm
for 2 minutes after warming upPulse generation
(See page 05 −82)
OX2A (E 12− 23) −E2 (E 13− 28)R −BRHeated oxygen sensorMaintain engine speed at 2,500 rpm
for 2 minutes after warming upPulse generation
(See page 05 −82)
OX2B (E 12− 29)
− O2B −(E 11 − 31)R −GHeated oxygen sensorMaintain engine speed at 2,500 rpm
for 2 minutes after warming upPulse generation
(See page 05 −82)
HT 1A(E 12− 5) −E03 (E 11 −7)
HT 1B(E 12− 25) −E03 (E 11 −7)
HT2A (E 12− 4) −E03 (E 11 −7)
HT2B (E 12− 33) −E03 (E 11 −7)Y−W −B
P −W −B
L −W −B
L − B
−W −B
Heated oxygen sensor
heaterIdlingBelow 3.0 V
HT 1A(E 12− 5) −E03 (E 11 −7)
HT 1B(E 12− 25) −E03 (E 11 −7)
HT2A (E 12− 4) −E03 (E 11 −7)
HT2B (E 12− 33) −E03 (E 11 −7)Y−W −B
P −W −B
L −W −B
L − B
−W −B
Heated oxygen sensor
heaterIgnition switch ON9to 14V
KNK 1(E 12−1 )− EKNK (E 12− 2)B −WKnock sensorMaintain engine speed at 4,000 rpm
after warming upPulse generation
(See page 05 −1 56)

−
DIAGNOSTICS SFI SYSTEM (2AZ−FSE)
05 −1 09
AVENSIS Supplement (RM 1045E)
DTC P0 136 OXYGEN SENSOR CIRCUIT MALFUNCTION
(BANK 1 SENSOR 2)
DTC P0 156 OXYGEN SENSOR CIRCUIT MALFUNCTION
(BANK 2 SENSOR 2)
CIRCUIT DESCRIPTION
Refer to DTC P0 130 on page 05 −82.
DTC NoDTC Detection ConditionTrouble Area
P0 136
P0 156
If the following two conditions are satisfied at a time
(2 trip detection logic):
(a) The ECM records cycles which the vehicle runs and stops
8 times or more
(b) There was no change in the rich and lean output from
heated oxygen sensor (sensor 2) for the 360 seconds un-
der air −fuel ratio feedback control (Throttle was not closed)
S Open or short in heated oxygen sensor circuit
S Heated oxygen sensor (Bank 1, 2 Sensor 2)
S Heated oxygen sensor heater (Bank 1, 2 Sensor 2)
S EFI relay
HINT:
S Bank 1 refers to the No. 1 and No. 4 cylinders.
S Bank 2 refers to the No. 2 and No. 3 cylinders.
S Sensor 2 refers to the sensor farthest away from the engine assembly.
WIRING DIAGRAM
Refer to DTC P0 130 on page 05 −82.
05CKC −02

+25 %
−12.5 %
More than 0.5 V
Less than 0.4V
Case1
Case 2
Case 3
Case 4
Output voltage of heated oxygen
sensor (sensor1: front sensor)
Injection volume
Output voltage
Output voltage of heated oxygen
sensor (sensor 2: rear sensor)Main suspect
trouble area
OK
+25 %
−12.5 %
More than 0.5 V
Less than 0.4V
Injection volume
Output voltage
+25 %
−12.5 %
More than 0.5 V
Less than 0.4V
Injection volume
Output voltage
Sensor1: front sensor
(sensor1, heater, sensor1
circuit)+25 %
−12.5 %
More than 0.5 V
Less than 0.4V
Injection volume
Output voltage
+25 %
−12.5 %
Injection volume
Output voltage
NG
+25 %
−12.5 %
Injection volume
Output voltage
NG
+25 %
−12.5 %
Injection volume
Output voltage
NG
+25 %
−12.5 %
Injection volume
Output voltage
NGExtremely rich or lean actual
air−fuel ratio
(Injector, fuel pressure, gas
leakage in exhaust system,
etc.) OK
OK
OK
Almost no reaction


Sensor 2: rear sensor
(sensor 2, heater, sensor 2
circuit)
Almost no reaction Almost no reactionAlmost no reaction
− DIAGNOSTICSSFI SYSTEM (2AZ−FSE)
05−111
AVENSIS Supplement (RM1045E)
NOTICE:
There is a delay of few seconds in the sensor1(front sensor) output, and there is about 20 seconds
delay at maximum in the sensor 2 (rear sensor).
The following A/F CONTROL procedure enables the technician to check and graph the voltage outputs of
both the heated oxygen sensor.
To display the graph, enter ACTIVE TEST/ A/F CONTROL/USER DATA, then select ”O2S B1S1and O2S
B1S2” or ”O2S B2S1and O2S B2S2” by pressing the ”YES” button followed by the ”ENTER” button and then
the ”F4” button.
NOTICE:
If the vehicle is short of fuel, the air−fuel ratio becomes LEAN and heated oxygen sensor DTCs will
be recorded, and the CHK ENG then illuminates.
HINT:
SIf different DTCs related to different systems that have terminal E2 as the ground terminal are output
simultaneously, terminal E2 may have an open circuit.
SRead freeze frame data usingthe hand−held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the
vehicle was running or stopped, if the engine was warmed up or not, if the air−fuel ratio was lean or
rich, and other data from the time the malfunction occurred.
SA high heated oxygen sensor (sensor1) voltage (0.5 V or more) could be caused by a rich air−fuel
mixture. Check for conditions that would cause the engine to run rich.