2005 TOYOTA AVENSIS drive shaft assy

05CDV−02
A83877
Ignition Coil Assy
Camshaft Position Sensor
VSV for EVAP
Combination Meter
DLC3
VSV for Intake Air Control Valve
Fuel Pump
ECM
Knock Sensor Camshaft Timing Oil Control Valve
(OCV)
Injector
Crankshaft Position
Sensor
Park/Neutral Position Switch
(Only for A/T Models)Engine Coolant
Temperature Sensor
Mass Air Flow Meter
Throttle Body Assy
Accelerator Pedal Assy
Heated Oxygen Sensor
(Bank 2 Sensor 2) *
2
Circuit Opening Relay
Heated Oxygen Sensor
(Bank1Sensor 2 ) *
1
Heated Oxygen Sensor
(Bank 2 Sensor1)*
2
Heated Oxygen Sensor
(Bank1Sensor1)*
1
Manifold Absolute Pressure Sensor
Fuel Pump (For High Pressure)
Injector Driver (EDU)
Brake Booster
Pressure Sensor
Fuel Pressure Sensor
(For Low Pressure)
FEFI Fuse
FIG2 Fuse
FAM2 Fuse
FTHROTTLE Fuse
FEFI Relay
FIG2 Relay
FINJ Relay
FEFI No.1Fuse
FEFI No.2 Fuse
FACT Fuse
FST Fuse
FIGN Fuse
FSTOP Fuse
FST Relay
Fuel Pump RelayFuel Pump Resister
*1: Bank1refers to the No.1and No.4 cylinders
*2: Bank 2 refers to the No.2 and No.3 cylinders
Engine Room R/B No.4:
Engine Room J/B No.4:Fuse Block:
Engine Room R/B No.1:
Engine Room J/B No.1:
Driver Side R/B:
Driver Side J/B: 05−2
− DIAGNOSTICSSFI SYSTEM (2AZ−FSE)
AVENSIS Supplement (RM1045E)
LOCATION

054JE−09
A85347
Mass Air Flow Meter
DLC3
Accelerator Pedal Assy
(Accelerator Pedal
Position Sensor)
EDUECM
Engine Room R/B No. 1:
FEDU Relay
FEDU Fuse
Glow Plug Relay
Camshaft Position SensorInjector
Crankshaft Position Sensor
Engine Coolant Temperature Sensor Fuel Pressure Sensor
Fuse Block
FST Fuse
Driver Side J/B
FGAUGE Fuse
FSTOP Fuse
Driver Side R/B
FST Relay
E−VRV Pressure Discharge Valve Glow Plug
Exhaust Gas Temperature
Sensor (on down stream)Intake Air Temperature Sensor
EGR Valve
Turbo Pressure Sensor
Intake Shutter (Throttle Valve)
Suction Control Valve
Fuel Temperature Sensor
Supply Pump Exhaust Gas Temperature
Sensor (on up stream)
Exhaust Fuel Addition Injector
A/F Sensor
Engine Room R/B No. 3:
FGLOW Fuse
EGR Valve
Position Sensor
Intake Shutter
(Throttle Valve)
Position Sensor
Differential Pressure Sensor 05−254
− DIAGNOSTICSECD SYSTEM (1CD−FTV)(From September, 2003)
AVENSIS Supplement (RM1045E)
LOCATION

05−136
− DIAGNOSTICSSFI SYSTEM (2AZ−FSE)
AVENSIS Supplement (RM1045E)
DTC P0200 INJECTOR CIRCUIT / OPEN
DTC P0201INJECTOR CIRCUIT / OPEN−(CYLINDER1)
DTC P0202 INJECTOR CIRCUIT / OPEN−(CYLINDER 2)
DTC P0203 INJECTOR CIRCUIT / OPEN−(CYLINDER 3)
DTC P0204 INJECTOR CIRCUIT / OPEN−(CYLINDER 4)
CIRCUIT DESCRIPTION
The Electronic Driver Unit (EDU) has been adopted to operate the injector at high speed. The EDU enables
the injector to drive in high−speed rate under high−pressure fuel condition using its internal DC/DC converter
that provides high voltage and quick−charging system.
The ECM constantly monitors the EDU. If the ECM detects abnormal condition, it will stop the engine.
DTC No.DTC Detection ConditionTrouble Area
P0200No IJF signals to ECM despite crankshaft rotating10 times
(1trip detection logic)
SOpen or short in EDU circuit
SEDU (Injector driver)
SFuel injector assy
SECM
P0200No IJF signals to ECM despite crankshaft rotating 20 times
during cranking (2 trip detection logic)
SOpen or short in EDU circuit
SEDU (Injector driver)
SFuel injector assy
SECM
P0201
P0202
P0203
P0204
No IJF signals of each cylinder to ECM 20 times successively
(1trip detection logic)
SOpen or short in EDU circuit
SEDU (Injector driver)
SFuel injector assy
SECM
05CKG−02

110U9−02
A85741
Air Cleaner Cap w/ Hose
Air Cleaner Element
Air Cleaner Case
7.0 (71, 62 in.
lbf)
N·m (kgf·cm, ft·lbf)
: Specified torque
Radiator Hose Outlet
Clip
Engine Room Cover Side
Clip
Retainer
Radiator Support
Opening Cover
8.0 (82, 71 in.
lbf)
5.5 (56, 49 in.
lbf)
V (Cooler Compressor
to Crankshaft Pulley)
Belt No. 1
Injector Driver
72 (734, 53)
52 (530, 38)52 (530, 38)
Engine Cover
Sub−assy No. 1
Engine Mounting Insulator Sub−assy RH
39 (398, 29)
Power Steering
Idle Pulley Bracket
52 (530, 38)
Clip
Engine Under Cover RH
Engine Under Cover Sub−assy No. 1
Clip
Radiator Reserve Tank Assy
6.0 (61, 53 in.
lbf)
x5
x3
Exhaust Gas Temperature
Sensor Connector
Vacuum Hose
Mass Air Flow Meter
Connector
− FUELINJECTION OR SUPPLY PUMP
ASSY (1CD−FTV)(From September, 2003)11−55
AVENSIS Supplement (RM1045E)
INJECTION OR SUPPLY PUMP ASSY (1CD−FTV)(From
September, 2003)
COMPONENTS

141NM−01
14 −166−
ENGINE MECHANICAL CYLINDER HEAD GASKET (1CD −FTV)(From
September, 2003)
AVENSIS Supplement (RM1045E)
REPLACEMENT
1. REMOVE FRONT WHEEL RH
2. REMOVE ENGINE UNDER COVER LH
3. REMOVE ENGINE UNDER COVER SUB −ASSY NO.1
4. REMOVE ENGINE UNDER COVER RH
5. REMOVE RADIATOR SUPPORT OPENING COVER
6. REMOVE ENGINE ROOM COVER SIDE
7. DRAIN ENGINE COOLANT (See page 16 −19)
8. DRAIN ENGINE OIL (See Pub. No. RM1018E on page 17 −30)
9. REMOVE ENGINE COVER SUB −ASSY NO.1 (See page 14 −90)
10. REMOVE VACUUM RESERVOIR SUB −ASSY (See page 14 −108)
11. REMOVE AIR CLEANER ASSY (See page 14 −108)
12. REMOVE BATTERY
13. REMOVE AIR TUBE NO.2 (See page 14 −108)
14. REMOVE AIR TUBE NO.1 (See page 14 −108)
15. REMOVE INJECTOR DRIVER (See page 14 −108)
16. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See Pub. No. RM1018E on page 14 −269)
17. REMOVE GENERATOR V BELT (See Pub. No. RM1018E on page 14 −269)
18. SEPARATE POWER STEERING IDLE PULLEY BRACKET (See page 14 −138)
19. DISCONNECT ENGINE WIRE (See page 14 −138)
20. DISCONNECT VACUUM HOSE (See page 14 −108)
21. REMOVE DIFFERENTIAL PRESSURE SENSOR ASSY(See page 14 −108)
22. REMOVE ENGINE MOUNTING INSULATOR SUB −ASSY RH (See page 14 −138)
23. REMOVE CRANKSHAFT PULLEY (See page 14 −138)
SST 09213 −54015 (09213 −70020), 09330 −00021, 09950 −50013 (09951 −05010, 09952 −05010,
09953 −05020, 09954 −05031)
24. REMOVE IDLER PULLEY SUB −ASSY (See page 14 −138)
25. REMOVE TIMING BELT NO.2 COVER (See page 14 −138)
26. REMOVE TIMING BELT NO.1 COVER (See page 14 −138)
27. REMOVE TIMING BELT GUIDE
28. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET (See page 14 −138)
29. SET NO. 1 CYLINDER TO TDC/COMPRESSION (See page 14 −138)
30. REMOVE TIMING CHAIN COVER PLATE (See page 14 −138)
31. REMOVE TIMING BELT (See page 14 −138)
HINT:
If reusing the timing belt, draw an arrow on the timing belt which indicates the engine revolution direction
and put match marks on the pulleys and timing belt.
32. REMOVE FUEL FILTER ASSY (See Pub. No. RM1018E on page 11 −82)
33. REMOVE HEATER PUMP ASSY (W/ COLD AREA) (See page 13 −12)
34. REMOVE HEATER BRACKET (W/ COLD AREA) (See page 13 −12)
35. REMOVE FLOOR PANEL BRACE FRONT (See page 15 −6)
36. REMOVE EXHAUST PIPE ASSY FRONT (See page 15 −6)
37. REMOVE EXHAUST PIPE ASSY (W/ COLD AREA) (See page 13 −12)
38. DISCONNECT RADIATOR HOSE INLET
39. DISCONNECT HEATER INLET WATER HOSE
40. DISCONNECT HEATER OUTLET WATER HOSE
41. DISCONNECT FUEL PIPE TO FUEL TUBE FUEL HOSE
42. DISCONNECT OIL COOLER HOSE

A85925
A09566
1
234 5
67 89
10 11
12 13
14 15
16
1718
A61194
Pry
−
ENGINE MECHANICAL CYLINDER HEAD GASKET (1CD −FTV)(From
September, 2003)14 −169
AVENSIS Supplement (RM1045E)
71. REMOVE NOZZLE LEAKAGE PIPE ASSY (See page 14 −151)
72. REMOVE INJECTOR ASSY (See page 11 −46)
HINT:
Since each injector assembly has characteristic fuel injecting behavior, keep them in the correct order so
that they can be returned to the original locations when reassembling. 73. REM O VE EXHAUST F UEL ADDI TI O N I NJECTO R
ASSY
(a) Using a Torx socket wrench (T40), remove the Torx screw.
NOTICE:
Be careful that the tools do not interfere with the resin part
when removing.
(b) Remove the nozzle holder clamp, addition injector and gasket.
74. REMOVE CAMSHAFT OIL SEAL RETAINER (See page 14 −151)
75. REMOVE CAMSHAFT (See page 14 −151)
76. REMOVE NO.2 CAMSHAFT (See page 14 −151)
77. REMOVE CYLINDER HEAD SUB −ASSY
(a) Using several steps, loosen the 18 cylinder head bolts
uniformly in the sequence shown in the illustration. Re-
move the 18 cylinder head bolts and plate washers.
NOTICE:
Removing the bolts in a wrong order could cause warpage
or cracks of the cylinder head.
(b) Lift the cylinder head from the dowels on the cylinder block, then place the cylinder head on wooden blocks on
a work bench.
NOTICE:
Be careful not to damage the contact surfaces of the cylin-
der head and cylinder block.
HINT:
To lift the cylinder head, pry between the cylinder head and cyl-
inder block using a screwdriver.
78. REMOVE CYLINDER HEAD GASKET

14−176−
ENGINE MECHANICAL CYLINDER HEAD GASKET (1CD −FTV)(From
September, 2003)
AVENSIS Supplement (RM1045E)
122. SET NO. 1 CYLINDER TO TDC/COMPRESSION (See page 14 −138)
SST 09960 −10010 (09962 −01000, 09963 −01000)
123. INSTALL TIMING BELT (See page 14 −138)
124. CHECK VALVE TIMING (See page 14 −138)
125. INSTALL TIMING CHAIN COVER PLATE (See page 14 −138)
126. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET (See page 14 −138)
127. INSTALL TIMING BELT GUIDE (See page 14 −138)
128. INSTALL TIMING BELT NO.1 COVER (See page 14 −138)
129. INSTALL TIMING BELT NO.2 COVER (See page 14 −138)
130. INSTALL IDLER PULLEY SUB −ASSY (See page 14 −138)
131. INSTALL CRANKSHAFT PULLEY (See page 14 −138)
SST 09213 −54015 (09213 −70020), 09330 −00021
132. INSTALL ENGINE MOUNTING INSULATOR SUB −ASSY RH (See page 14 −138)
133. INSTALL POWER STEERING IDLE PULLEY BRACKET (See page 14 −108)
134. ADJUST V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See Pub. No. RM1018E on page 14 −269)
135. INSTALL INJECTOR DRIVER (See page 14 −108 )
136. INSTALL AIR TUBE NO.1 (See page 14 −108)
137. INSTALL AIR TUBE NO.2 (See page 14 −108)
138. INSTALL DIFFERENTIAL PRESSURE SENSOR ASSY (See page 14 −108)
139. INSTALL BATTERY (See page 14 −108)
140. INSTALL AIR CLEANER ASSY (See page 14 −108)
141. INSTALL VACUUM RESERVOIR SUB −ASSY (See page 14 −108)
142. INSTALL ENGINE COVER SUB −ASSY NO.1 (See page 14 −90)
143. INSTALL FRONT WHEEL RH Torque: 103 N
m (1,050 kgf
cm, 76 ft
lbf)
144. ADD ENGINE OIL (See Pub. No. RM1018E on page 17 −30)
145. ADD ENGINE COOLANT (See page 16 −19)
146. CHECK FOR FUEL LEAKS (See page 11 −46)
147. CHECK FOR ENGINE OIL LEAKS
148. CHECK FOR ENGINE COOLANT LEAKS (See page 16 −15)
149. CHECK FOR EXHAUST GAS LEAKS

141NK−01
SSTA61187
−
ENGINE MECHANICAL CAMSHAFT (1CD−FTV)(From September, 2003)
14 −151
AVENSIS Supplement (RM1045E)
REPLACEMENT
1. REMOVE FRONT WHEEL RH
2. REMOVE ENGINE UNDER COVER LH
3. REMOVE ENGINE UNDER COVER SUB −ASSY NO.1
4. REMOVE ENGINE UNDER COVER RH
5. REMOVE RADIATOR SUPPORT OPENING COVER
6. REMOVE ENGINE ROOM COVER SIDE
7. REMOVE ENGINE COVER SUB −ASSY NO.1 (See page 14 −90)
8. REMOVE AIR CLEANER ASSY (See page 14 −108)
9. REMOVE BATTERY
10. REMOVE VACUUM RESERVOIR SUB −ASSY (See page 14 −108)
11. REMOVE AIR TUBE NO.1 (See page 14 −108)
12. REMOVE INJECTOR DRIVER (See page 14 −108)
13. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (See Pub. No. RM1018E on page 14 −269)
14. REMOVE GENERATOR V BELT (See Pub. No. RM1018E on page 14 −269)
15. SEPARATE POWER STEERING IDLE PULLEY BRACKET (See page 14 −138)
16. DISCONNECT ENGINE WIRE (See page 14 −138)
17. DISCONNECT VACUUM HOSE (See page 14 −108)
18. REMOVE ENGINE MOUNTING INSULATOR SUB −ASSY RH (See page 14 −138)
19. REMOVE CRANKSHAFT PULLEY (See page 14 −138)
SST 09213 −54015 (09213 −70020), 09330 −00021, 09950 −50013 (09951 −05010, 09952 −05010,
09953 −05020, 09954 −05031)
20. REMOVE IDLER PULLEY SUB −ASSY (See page 14 −138)
21. REMOVE TIMING BELT NO.2 COVER (See page 14 −138)
22. REMOVE TIMING BELT NO.1 COVER (See page 14 −138)
23. REMOVE TIMING BELT GUIDE
24. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET (See page 14 −138)
25. SET NO. 1 CYLINDER TO TDC/COMPRESSION (See page 14 −138)
26. REMOVE TIMING CHAIN COVER PLATE (See page 14 −138)
27. REMOVE TIMING BELT (See page 14 −138)
28. REMOVE CAMSHAFT POSITION SENSOR (See page 14 −108)
29. REMOVE CAMSHAFT TIMING PULLEY
(a) Using SST, remove the pulley bolt. SST 09960 −10010 (09962 −01000, 09963 −01000)
(b) Remove the timing pulley.
HINT:
Using a plastic −faced hammer, tap out the pulley.
(c) Remove the set key.
30. REMOVE FUEL PIPE NO.3 (See page 14 −108)
SST 09023 −12700