2005 TOYOTA AVENSIS heater

A77308
A77303
A77340
14±206
±
ENGINE MECHANICAL PARTIAL ENGINE ASSY(1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
25.SEPARATE VANE PUMP OIL RESERVOIR ASSY 26.REMOVE OIL RESERVOIR BRACKET NO.1
(a)Remove the 2 bolts and the oil reservoir bracket No. 1.
27.SEPARATE COOLER REFRIGERANT SUCTION HOSENO.1 (LHD STEERING POSITION TYPE)
(a)Remove the 2 nuts and separate the suction hose.
28.REMOVE COOL ER BRACKET (LHD STEER ING
POSITION TYPE)
(a)Remove the nut and separate the cooler bracket.
29.REMOVE ENGINE SERVICE COVER BRACKET RH (RHD STEERING POSITION TYPE)
(a)Remove the bolt and the service cover bracket RH.
30.DISCONNECT HEATER INLET WATER HOSE
31.DISCONNECT HEATER OUTLET WATER HOSE
32.REMOVE CHARCOAL CANISTER ASSY
33.DISCONNECT FUEL TUBE SUB±ASSY (See page 11±30)
34. DISCONNECT UNION TO CONNECTOR TUBE HOSE
35.REMOVE FLOOR PANEL BRACE FRONT (See page 15±7)
36.REMOVE EXHAUST PIPE ASSY CENTER (See page 15±7)
37.REMOVE EXHAUST PIPE ASSY FRONT (See page 15±7)
38.REMOVE FRONT AXLE HUB LH NUT (See page 30±6) SST 09330±00030

A77313
Cooler Bracket
(LHD Steering Position Type)
Oil Reservoir
Bracket No. 1Heater Outlet Water Hose
Heater Inlet Water Hose
Steering Intermediate
Shaft Assy No. 2
Column Hole Cover Silercer Sheet
Front Stabilizer Link Assy
Front Axle Assy
35 (360, 26)
7.0 (71, 62 in.
lbf)
74 (755, 55)
216 (2,203,159 )
142 (1,448,105 )
N´m (kgf´cm, ft´lbf)
: Specified torque

Non±reusable part
Front Axle Hub Nut
Tie Rod End Sub±assy
5.0 (51, 44 in.
lbf)
5.0 (51, 44 in.
lbf)

Cotter Pin
49 (500, 36)
Front Suspension Arm
Sub±assy Lower No. 1
± ENGINE MECHANICALPARTIAL ENGINE ASSY (1AZ±FSE)
14±195
AVENSIS REPAIR MANUAL (RM1018E)

A77369
N´m (kgf´cm, ft´lbf)
: Specified torque

Non±reusable part
10 (97, 84 in.
lbf)
10 (97, 84 in.
lbf)

Gasket
Intake Air Control Valve

GasketInsulator
10 (97, 84 in.
lbf)
Intake Manifold

Gasket
Water By±pass
Hose No. 1
Throttle Body Assy
Water By±pass
Hose No. 2
21 (210, 15)
Throttle Body
Bracket
8.4 (86, 74 in.
lbf)
8.0 (82, 71 in.
lbf)
Water By±pass Hose No. 1
Heater Water Inlet Hose 14±200
± ENGINE MECHANICALPARTIAL ENGINE ASSY (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)

A79418N´m (kgf´cm, ft´lbf)
: Specified torque
25 (255, 18)
18 (178, 13)
Injector Driver
Air Tube No. 2Union To Connector Tube Hose
Fuel Filter AssyHeater Inlet Water Hose Heater Outlet Water Hose Vacuum Reservoir Sub±assy
8.3 (85, 73 in.
lbf)
5.0 (51, 44 in.
lbf)
14±278
± ENGINE MECHANICALPARTIAL ENGINE ASSY (1CD±FTV)
AVENSIS REPAIR MANUAL (RM1018E)

A77302
A77353
±
ENGINE MECHANICAL CYLINDER HEAD GASKET(1AZ±FSE)
14±257
AVENSIS REPAIR MANUAL (RM1018E)
(e)Raise a clamp up, and slide it toward the air cleaner cap,
then remove the air cleaner cap from its case.
(f)Remove the air cleaner element.
(g)Remove the 4 bolts and the air cleaner case.
43.DISCONNECT RADIATOR HOSE INLET
44.DISCONNECT UNION TO CONNECTOR TUBE HOSE
45.DISCONNECT HEATER INLET WATER HOSE
46.SEPARATE FUEL TUBE SUB±ASSY
47.SEPARATE ENGINE WIRE
48.REMOVE THROTTLE BODY ASSY (See page 10±44)
49. REMOVE CHARCOAL CANISTER ASSY 50. REMOVE INTAKE MANIFOLD
(a) Remove the 5 bolts and 2 nuts.
(b) Disconnect the 2 vacuum hoses.
(c) Remove the 2 stud bolts.
(d) Remove the intake manifold and insulator.
51. REMOVE INTAKE AIR CONTROL VALVE ASSY
(a) Remove the intake air control valve and gasket.
52. REMOVE MANIFOLD CONVERTER INSULATOR NO.1
(a) Disconnect the oxygen sensor connector.
(b) Remove the 2 bolts and nut, and then remove the manifold insulator.

A77373
Throttle Body Assy
Water By±pass Hose No. 2
N´m (kgf´cm, ft´lbf)
: Specified torque

Non±reusable part
Gasket
Water By±pass
Hose No. 1
Throttle Body Bracket
8.0 (82, 71 in.
lbf)
8.4 (86, 74 in.
lbf)
Heater Inlet Water Hose
Union to Connector Tube Hose
Radiator Hose Inlet
Fuel Tube Sub±assy
Fuel Pipe Clamp
5.0 (51, 44 in.
lbf)
Air Cleaner Assembly
with Hose
5.0 (51, 44 in.
lbf)
Battery Clamp
Battery
Battery Tray 14±248
± ENGINE MECHANICALCYLINDER HEAD GASKET (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)

A79801
N´m (kgf´cm, ft´lbf)
: Specified torque

Non±reusable part
Gasket
10 (97, 84 in.
lbf)
10 (97, 84 in.
lbf)
Intake Manifold
10 (97, 84 in.
lbf)
Insulator
Intake Air Control Valve
Assy

Gasket
Water By±pass Hose No. 1
Heater Water Inlet Hose
± ENGINE MECHANICALCYLINDER HEAD GASKET (1AZ±FSE)
14±251
AVENSIS REPAIR MANUAL (RM1018E)

141CA±01
14±332
±
ENGINE MECHANICAL CYLINDER HEAD GASKET(1CD±FTV)
AVENSIS REPAIR MANUAL (RM1018E)
REPLACEMENT
1.REMOVE FRONT WHEEL RH
2.REMOVE ENGINE UNDER COVER LH
3.REMOVE ENGINE UNDER COVER SUB±ASSY NO.1
4.REMOVE ENGINE UNDER COVER RH
5.DRAIN ENGINE COOLANT (See page 16±44)
6.DRAIN ENGINE OIL (See page 14±342)
7. REMOVE RADIATOR SUPPORT OPENING COVER
8. REMOVE ENGINE ROOM COVER SIDE
9. REMOVE ENGINE COVER NO.1
(a) Remove the 5 nuts and the engine cover.
10.REMOVE VACUUM RESERVOIR SUB±ASSY (See page 13±11)
11.REMOVE AIR CLEANER ASSY (See page 14±286)
12. REMOVE BATTERY
13.REMOVE AIR TUBE NO.2 (See page 14±286)
14.REMOVE AIR TUBE NO.1(See page 14±270)
15.REMOVE INJECTOR DRIVER (See page 14±286)
16. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (See page 14±269)
17.REMOVE GENERATOR V BELT (See page 14±269)
18.SEPARATE POWER STEERING IDLE PULLEY BRACKET (See page 14±286)
19.REMOVE ENGINE MOUNTING INSULATOR SUB±ASSY RH(See page 14±307)
20.REMOVE CRANKSHAFT PULLEY(See page 14±307)
SST 09213±54015 (90105±08076), 09330±00021, 09950±50013 (0995\
1±05010, 09952±05010, 09953±05020, 09954±05031)
21.REMOVE IDLER PULLEY SUB±ASSY(See page 14±307)
22.REMOVE TIMING BELT NO.2 COVER(See page 14±307)
23.REMOVE TIMING BELT NO.1 COVER(See page 14±307)
24. REMOVE TIMING BELT GUIDE
25.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET(See page 14±307)
26.SET NO. 1 CYLINDER TO TDC/COMPRESSION(See page 14±307)
27.REMOVE TIMING CHAIN COVER PLATE(See page 14±307)
28.REMOVE TIMING BELT(See page 14±307)
HINT:
If re±using the timing belt, draw a direction arrow on the timing belt (\
in direction of engine revolution), and
place matchmarks on the pulleys and the timing belt.
29.REMOVE FUEL FILTER ASSY (See page 11±82)
30.REMOVE HEATER PUMP ASSY (W/ COLD AREA) (See page 13±11)
31.REMOVE HEATER BRACKET (W/ COLD AREA) (See page 13±11)
32.REMOVE FLOOR PANEL BRACE FRONT(See page 15±10)
33.REMOVE EXHAUST PIPE ASSY FRONT(See page 15±10)
34.REMOVE EXHAUST PIPE ASSY (W/ COLD AREA) (See page 13±11)
35. DISCONNECT RADIATOR HOSE INLET
36. DISCONNECT HEATER INLET WATER HOSE
37. DISCONNECT HEATER OUTLET WATER HOSE
38. DISCONNECT FUEL PIPE TO FUEL TUBE FUEL HOSE
39. DISCONNECT OIL COOLER HOSE
40.REMOVE TURBO INSULATOR NO.2 (See page 13±11)
41.REMOVE TURBO INSULATOR NO.1 (See page 13±11)