2005 TOYOTA AVENSIS oil

D03809
Vinyl Tape
SST
D03810
SST
D03794
O−ringO−ring
D26764
Underdrive
Brake Piston
− AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
40−45
U151E, U151F A/T REPAIR MANUAL (RM1021U)
88. INSTALL NEEDLE ROLLER BEARING
(a) Wind a vinyl tape around SST at the place 4.0 mm (0.157
in.) above from the bottom end until the thickness of the
wound tape is about 5.0 mm (0.197 in.).
NOTICE:
Clean SST to remove deposited oil, before winding a vinyl
tape.
(b) Coat the needle roller bearing with ATF.
(c) Using SST and a press, install the needle−roller bearing
to the transaxle case.
SST 09950−60010 (09951−00320), 09950−70010
(09951−07100)
NOTICE:
When the wound vinyl tape contacts the transaxle case,
stop press−fitting.
89. INSTALL UNDERDRIVE BRAKE PISTON
(a) Coat the 2 new O−rings with ATF, install them to the un-
derdrive brake piston.
NOTICE:
SAssemble the O−ring carefully not to have a twist and
a pinching.
SApply enough ATF to the O−ring prior to assembling.
(b) Coat the underdrive brake piston with ATF.
(c) Install the underdrive brake piston to the transaxle case.
NOTICE:
Be careful not to damage the O−ring.

D26766
SST
D26389
Rear Clutch
Oil Seal
Ring Outer
D26388
D26454
FIPG
− AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
40−57
U151E, U151F A/T REPAIR MANUAL (RM1021U)
113. INSTALL NEEDLE ROLLER BEARING
(a) Using SST and a press, install the needle roller bearing
to the transaxle rear cover.
SST 09950−60010 (09951−00230, 09952−06010)
Press fit depth: 20.55−21.25 mm (0.8091−0.8366 in.)
NOTICE:
SFace the inscribed mark side of the bearing race up.
SRepeat the press fit until the specified value is ob-
tained.
(b) Coat a needle roller bearing with ATF.
114. INSTALL REAR CLUTCH OIL SEAL RING OUTER
(a) Coat the 3 new rear clutch oil seal rings with ATF, install
them to the transaxle rear cover.
NOTICE:
The snap ring should be fixed certainly in the groove of the
drum.
115. INSTALL TRANSAXLE CASE NO.1PLUG
(a) Install the 4 new O−ring to the 4 transaxle case No. 1
plugs.
(b) Install the 4 transaxle case No. 1 plugs to the transaxle
rear cover.
Torque: 7.4 Nm (75 kgfcm, 65 in.lbf)
116. INSTALL TRANSAXLE REAR COVER SUB−ASSY
(a) Remove any packing material and be careful not to get oil
on the contacting surfaces of the transaxle rear cover or
the transaxle case.
(b) Apply FIPG to the cover.
FIPG:
Part No. 08826−00090, THREE BOND1281or equiva-
lent.
NOTICE:
Concerning about the amount of the FIPG application, the
amount should be controlled to from even sealing film on
entire flange surface and have slight protrusion of the FIPG
all around of the connecting area. The FIPG shall be ap-
plied continuously on the flange. (Reference value of the
section diameter:
1.2)

D03580
D09691
Parking Lock Pawl
Spring
Pawl Pin
D26386
D03579
Underdrive
Planetary
Gear Assy
40−60
− AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
U151E, U151F A/T REPAIR MANUAL (RM1021U)
121. INSTALL UNDERDRIVE CLUTCH ASSY
(a) Coat the bearing and bearing race with petroleum jelly,
install them onto the underdrive clutch.
Bearing and bearing race diameter: mm (in.)
InsideOutside
Bearing37.73 (1.4854)58.0 (2.2835)
Race29.9 (1.1772)55.5 (2.185)
(b) Install the underdrive clutch assy to the transaxle case.
NOTICE:
Installing the underdrive clutch drum sub−assy, be sure
not to damage the oil seal ring.
122. INSTALL PARKING LOCK PAWL
(a) Install the pawl pin and spring to the parking lock pawl.
(b) Temporarily install the parking lock pawl, shaft and spring
to the transaxle case, as shown in the illustration.
123. INSTALL UNDERDRIVE PLANETARY GEAR ASSY
(a) Install the underdrive planetary gear assy to the transaxle
case.
NOTICE:
Engage all the discs of underdrive clutch and hub splines
of the underdrive planetary gear assy firmly and assemble
them securely.

D03569
D03629
O−ring
D03630Seal Bend Width 1.2 mm (0.047 in.) FIPG
40−64
− AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
U151E, U151F A/T REPAIR MANUAL (RM1021U)
Bearing and bearing race diameter: mm (in.)
InsideOutside
Bearing57.2 (2.252)84.96 (3.345)
Bearing race56.4 (2.22)83 (3.268)
130. INSTALL OIL PUMP ASSY
(a) Install the oil pump to the transaxle case with the 7 bolts.
Torque: 22.0 Nm (226 kgfcm,16ftlbf)
(b) Coat the O−ring of oil pump with ATF.
NOTICE:
Confirm the input shaft rotates smoothly with the manual
operation after assembling the oil pump.
131. INSTALL TRANSAXLE HOUSING
(a) Remove any parking material and be careful not to get oil
on the contacting surface of the transaxle case or trans-
axle housing.
(b) Apply FIPG to the transaxle case.
FIPG:
Part No. 08826−00090, THREE BOND1281or equiva-
lent

D25608
C
C
CAB2WD:
4WD:
B
D
C CC
CB
B
A
A
D08091
D03631
D26468
SST
− AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
40−65
U151E, U151F A/T REPAIR MANUAL (RM1021U)
(c) Install the transaxle housing and 16 bolts to the transaxle
case.
Torque:
Bolt A: 25 Nm (255 kgfcm,18ftlbf)
Bolt B: 33 Nm (337 kgfcm, 24 ftlbf)
Bolt C: 29 Nm (295 kgfcm, 21ftlbf)
Bolt D: 22 Nm (226 kgfcm,16.0 ftlbf)
HINT:
Apply seal packing or equivalent to the bolt A and D.
Seal packing:
THREE BOND 2403 or equivalent
Bolt length:
Bolt A: 50 mm (1.969 in.)
Bolt B: 50 mm (1.969 in.)
Bolt C: 42 mm (1.654 in.)
Bolt D: 72 mm (2.835 in.)
NOTICE:
Because the bolt A is a seal bolt, apply the seal packing to
new bolts and tighten them within10 minutes after applica-
tion.
132. INSPECT INPUT SHAFT ENDPLAY
(a) Using a dial indicator, measure the input shaft end play.
End play: 0.262−1.249 mm (0.0100−0.0494 in.)
133. FIX AUTOMATIC TRANSAXLE ASSY
(a) Fix the transaxle assy.
134. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL
(a) Coat a new oil seal with MP grease.
(b) Install the oil seal to the transaxle case.
SST 09950−60010 (09951−00230), 09950−70010
(09951−07100)
Oil seal drive in depth: 0á0.5 mm (0á0.0197 in.)

D26382
Parking Lock Rod Sub−assy
D03565
Spacer
D03564
D26765
D03559
40−66
− AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
U151E, U151F A/T REPAIR MANUAL (RM1021U)
135. INSTALL PARKING LOCK ROD SUB−ASSY
(a) Install the parking lock rod to the manual valve lever.
136. INSTALL MANUAL VALVE LEVER SUB−ASSY
(a) Install a new spacer and manual valve lever shaft to the
transaxle case.
NOTICE:
Do not damage on the oil seal during assembling the shaft
to the transaxle case.
(b) Using a pin punch and hammer, drive in a new pin.
(c) Turn the spacer and the lever shaft to align the small hole
for locating the staking position in the spacer with the
staking position mark on the lever shaft.
(d) Using a pin punch, stake the spacer through the small
hole.
(e) Check that the spacer does not turn.
137. INSTALL MANUAL VALVE LEVER SHAFT RETAINER
SPRING
(a) Using needle−nose pliers, install the retainer spring.
NOTICE:
Hang the spring on the shaft certainly.

D03547
Transmission Wire
C91927
GFE
A
B
C
D
C91933
A
CB
B
A
C
L
L
C91932
O−ring
40−70
− AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
U151E, U151F A/T REPAIR MANUAL (RM1021U)
(b) Install the transmission wire retaining bolt.
Torque: 5.4 Nm (55 kgfcm, 48 in.lbf)
148. CONNECT TRANSMISSION WIRE
(a) Coat a O−ring of the ATF temperature sensor with ATF.
(b) Install the ATF temperature sensor, with the lock plate and
bolt.
Torque: 6.6 Nm (67 kgfcm, 58 in.lbf)
(c) Connect the 7 solenoid connectors.
NOTICE:
SConnect the connector to A, B, C, D, E, F, G, from
shorter one.
SApply ATF to the bolt.
149. INSTALL TRANSMISSION VALVE BODY ASSY
(a) Make sure that the manual valve lever position, install the
valve body with 17 bolts to the transaxle case.
Torque:11Nm(110 kgfcm, 8 ftlbf)
Bolt length:
Bolt A: 41mm (1.614 in.)
Bolt B: 57 mm (2.244 in.)
Bolt C: 25 mm (0.984 in.)
NOTICE:
SPush the valve body against the accumulator piston
spring and the check ball body to install it.
SWhen installing the valve body to the transaxle case,
do not hold the solenoids.
STighten temporarily those bolts marked byLin the il-
lustration first because they are positioning bolts.
150. INSTALL VALVE BODY OIL STRAINER ASSY
(a) Coat a new O−ring with ATF, install it to the oil strainer.
NOTICE:
Assemble the O−ring carefully not to have a twist and a
pinching. Moreover, apply enough ATF to the O−ring prior
to assembling.

C91931
Valve Body Oil
Strainer Assy.
C86316
Magnet
C91925
D26716
D03900D30672
Speed Sensor
− AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
40−71
U151E, U151F A/T REPAIR MANUAL (RM1021U)
(b) Install the oil strainer and 3 bolts to the valve body.
Torque:11Nm(110 kgfcm, 8 ftlbf)
NOTICE:
Apply ATF to the bolts.
151. INSTALL AUTOMATIC TRANSAXLE OIL PAN
SUB−ASSY
(a) Install the 2 magnets in the oil pan.
(b) Apply seal packing or equivalent to new 18 bolts.
Seal packing:
THREE BOND 2430 or equivalent
(c) Install the new oil pan gasket with the 18 bolts to the trans-
axle case.
Torque: 7.8 Nm (80 kgfcm, 69 in.lbf)
NOTICE:
SBecause the bolts should be seal bolts, apply seal
packing to new bolts and tighten them within10 min-
utes after application.
SRemove any oil or grease from the contacting surface
of the transaxle case and the oil pan with the gasket
completely before the oil pan to the case.
152. INSTALL TRANSAXLE CASE NO.1PLUG
(a) Coat the 4 new O−rings with ATF, install them to the 4
transaxle case No. 1 plugs.
(b) Install the 4 transaxle case No. 1 plugs to the transaxle
case.
Torque: 7.4 Nm (75 kgfcm, 65 in.lbf)
153. INSTALL SPEED SENSOR
(a) Install them to the 2 sensors.
(b) Install the 2 sensors to the transaxle case with the 2 bolts.
Torque:11.0 Nm(115 kgfcm, 8 ftlbf)