2005 Citroen XSARA PICASSO Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 275
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: RHR
Remove:
- The screw (8).
- The auxiliaries drive pulley (7).
- The crankshaft position sensor (11).
- The lower timing cover (9).
- The target of the crankshaft position sensor (10), using tool [7].
- The lower torque reaction rod.
- The tool [6].
Slacken the screw (12)of the tensioner roller (17).
Remove the timing belt (13).
Checks.
IMPERATIVE: Just before refitting, carry out the checks below.
Check:
- That the rollers (14)and (17)turn freely
(without play and without
any tight spot).
- That the coolant pump pulley (16)turns freely (without play and
without any tight spot).
- That there are no traces of oil leaks from the crankshaft and
camshaftseals, etc.
- That the crankshaft pinion travels freely on the keyway (15).
Replace defective components if necessary.
B1EP1FCC
B1EP1FDC
B1EP1FEC
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 275

Downloaded from www.Manualslib.com manuals search engine 276
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: RHR
Refitting.
Centre the crankshaft pinion (15), using tool [5].
Reposition the timimg belt on the pulley (18).
Put the tool [4]in place
(tighten moderately).
Reposition the timimg belt, strip «a»well tensioned
in the following order:
- Guide roller (14).
- Crankshaft pinion (15).
- Coolant pump pinion (16).
- Tensioner roller (17).
Remove tools [4]and [5].
Bring the index «d»outside the plate at «c», by
turning the tensioner roller in the direction of the
arrow «b», using a hexagonal spanner at «e».
Tighten screw (12)of the tensioner roller (17)to
2,1 ± 0,2 m.daN.
Lock the flywheel, by means of tool [6].
Refit the auxiliaries drive pulley (7).
Tighten the screw (8)to 7 ± 0,7 m.daN.
Remove tools [6], [2]and [3].
B1EP1FFC
B1EP1FGC
B1EP1FHC
B1EP1FJC
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 276

Downloaded from www.Manualslib.com manuals search engine 277
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: RHR
Refitting.
Rotate the crankshaft ten times
(in the direction of rotation of the engine).
Peg the crankshaft, using tool [2] and the camshaft drive pinion, using tool [3].
Lock the flywheel, using tool [6].
Slacken the screw (8)of the auxiliaries drive pulley (7) and the screw (12)of
the tensioner roller (17).
Turn the tensioner roller
(clockwise), using a hexagonal spanner at «e».
Position the index «d»opposite the notch «f».
Tighten:
- The screw (12)of the tensioner roller (17)to 2,1 ± 0,2 m.daN.
- The auxiliaries drive pulley to 7 ± 0,7 m.daN.
Remove tools [2], [3]and [6].
Rotate the crankshaft two times
(in the direction of rotation of the engine).
Refit tools [2]and [3].
Check the position of the index «d», it should be opposite the notch «f».
B1EP1FKC
B1EP1FLC
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 277

Downloaded from www.Manualslib.com manuals search engine 278 278
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: RHR
Refitting.
IMPERATIVE: If the position of the index «d» is not correct, restart the operations to tension
the timing belt
(for this, slightly slacken the screw (12) of the tensioner roller).
Refit tool [6].
Remove the auxiliaries drive pulley (7).
Refit:
- The crankshaft position sensor target (10).
- The lower timing cover (9).
- The crankshaft position sensor (11).
- The lower torque reaction rod.
Take away the workshop hoist.
Coat the screw (8)with Loctite FRENETANCH.
Refit the auxiliaries drive pulley (7) and the screw (8)with its washer.
Tighten the screw (8)to 7 ± 0,7 m.daN, then angular tighten by A= 60°±5°.
Remove tools [2], [3] and [6].
Complete the refitting.
B1EP1FKC
B1EP1FLC
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 278

Downloaded from www.Manualslib.com manuals search engine ENGINE
279
C4CHECKING THE OIL PRESSURE
Petrol Diesel
Engine type KFU NFU RFJ RFN RFK 9HX 9HY 9HZ RHR
Temperature (°C) 90° 80°
Pressure (bars) 1,5 3 1,3 1,9
Rpm1000
Pressure (bars) 3 5,6 4
Rpm 2000 2000 2000
Pressure (bars) 5 6,3
Rpm 3000 3000
Pressure (bars) 43,5
Rpm 40004000
Tools (Toolkit 4103)
2279-T.Bis X X X X X X X X X
4103-T X X X X X X X X X
(-).0710.F1 X
(-).0710.B1 X
(-).1503.JXX X
4103-T.B X X
7001-T X X X X X
4202-T X X
NOTE: The oil pressure should be checked with the engine hot, after the oil level has been checked.
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 279

Downloaded from www.Manualslib.com manuals search engine 280
ENGINECHECKING THE OIL PRESSURE
To be read with the Petrol and Diesel correspondence tables
XSARA
Engine type KFW NFU RFN 8HZ 8HX WJY RHY RHZ
Temperature (°C) 90°C
Pressure (bars) 1,5 1,3 1,8 2
Rpm 1000 1000
Pressure (bars) 3
Rpm 2000
Pressure (bars) 4
Rpm 3000
Pressure (bars) 5,1 3,5 4,5 4
Rpm4000
Tools (Toolkit 4103-T)
2279-T.Bis X X X X X X X
4103-T X X X X X X X
4202-T X X X
1503-JX
3099-TX
7017-T.X23X
NOTE: The oil pressure should be checked with the engine hot, after the oil level has been checked.
XSARA
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 280

Downloaded from www.Manualslib.com manuals search engine 281
ENGINE
CHECKING THE OIL PRESSURE
To be read with the Petrol and Diesel correspondence tables
XSARA PICASSO
Engine type NFV 6FZ RFN 9HZ 9HY RHY
Temperature (°C) 90°C 80°C 90°C
Pressure (bars) 3,3 1,5 1,3 2
Rpm 1000
Pressure (bars) 3
Rpm 2000
Pressure (bars) 5
Rpm 3000
Pressure (bars) 4 6,3 3,5 4
Rpm 4000 4000
Tools (Toolkit 4103-T)
2279-T.Bis X X X X X X
4103-T X X X X X X
7001-T X
4202-T X X X
1503-J X X
NOTE: The oil pressure should be checked with the engine hot, after the oil level has been checked.
XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 281

Downloaded from www.Manualslib.com manuals search engine 282
ENGINEVALVE CLEARANCE SETTINGS
The valve clearances must be checked with the engine cold.
●Inlet
TU1JP - TU3JP
(except TU5JP4)
WJY
TU5JP4
DV4/DV6/EW10
All typesExhaust
Hydraulic adjustment 0,15 mm ± 0,08
0,30mm ± 0,08
Rocking
Adjust
1 ●1
3 ●3
4 ●4
2 ●24 ●4
2 ●2
1 ●1
3 ●3
Exhaust
●
Inlet Rocking
Valves
fully
openAdjust
1
3
4
23 ●4
4 ●2
2 ●1
1 ●3
Fully open (exhaust) POSSIBLE PROCEDURES
For engines with 4 cylinders in a line (1-3-4-2 )
Engines without hydraulic
adjustment: the clearance (J)
should be checked opposite
the cam.
B1DP13QC
0,20 mm ± 0,05
0,40 mm ± 0,05
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 282