step.
2. Erase, then retrieve DTCs. Turn ignition off. If DTCs are retrieved, go to next
step. If DTCs are not retrieved, an intermittent condition may exist.
3. If DTC B1530, B1531, B1532, B1533, B1534, B1535, B1536, B1537, B1538,
B1539, B1540, B1541, B1542, B1543, B1545 or B1546 is retrieved, diagnose
appropriate DTC. See DIAGNOSTIC TROUBLE CODES (DTCS) IDENTIFICATION WITH SINGLE
-STAGE AIR BAG SYSTEM
table. If
DTC B1530, B1531, B1532, B1533, B1534, B1535, B1536, B1537, B1538,
B1539, B1540, B1541, B1542, B1543, B1545 or B1546 is not retrieved, go to
next step.
4. Visually inspect passenger seat belt warning light connector C-38. See Fig. 30
.
If connector C-38 is connected correctly, go to next step. If connector C-38 is
not connected correctly, properly connect connector. Go to step 10 .
5. Disconnect connector C-38. Measure voltage between ground and connector
C-38, terminal No. 1 (Black/White wire). See Fig. 40
. If voltage is not about
12 volts, go to next step. If voltage is about 12 volts, go to step 7 .
6. Inspect Black/White wire between terminal No. 1 of connector C-38 and
terminal No. 2 of ignition switch connector C-308, including junction block
connectors C-211 and C-215. See Fig. 22
. If wire is okay, go to next step. If
wire is not okay, repair as necessary. See WIRE REPAIR
. Go to step 10 .
7. Inspect SRS ECU connector C-26. See SRS ELECTRONIC CONTROL
UNIT (SRS ECU)
under REMOVAL & INSTALLATION. If SRS ECU
connector C-26 is connected correctly, go to next step. If SRS ECU connector
C-26 is not connected correctly, properly connect connector. Go to step 10 .
8. Check Pink wire between connector C-07, terminal No. 3 and SRS ECU
connector C-26, terminal No. 42, for damage, shorts or open circuits. See Fig.
33 . If wire is okay, go to next step. If wire is not okay, repair as necessary. See
WIRE REPAIR
. Go to step 10 .
9. Disconnect negative battery cable. Disconnect SRS ECU connector C-26.
Connect negative battery cable. Connect a jumper wire between ground and
SRS ECU connector C-26, terminal No. 42. If passenger seat belt warning light
does not illuminate, replace passenger seat belt warning light assembly. Go to
next step. If passenger seat belt warning light illuminates, erase, then retrieve
DTCs. If DTC B1487 is retrieved, re
place SRS ECU. Go to next ste
p.
2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems
appropriate DTC. See DIAGNOSTIC TROUBLE CODES (DTCS) IDENTIFICATION WITH SINGLE
-STAGE AIR BAG SYSTEM
table. If
DTC B1540, B1541, B1542, B1543, B1545 or B1546 is not retrieved, go to
next step.
4. Visually inspect PASSENGER AIR BAG OFF indicator connector C-37. See
Fig. 30
. If connector C-37 is connected correctly, go to next step. If connector
C-37 is not connected correctly, properly connect connector. Go to step 10 .
5. Disconnect connector C-37. Measure voltage between ground and connector
C-37, terminal No. 1 (Black/White wire). See Fig. 41
. If voltage is not about
12 volts, go to next step. If voltage is about 12 volts, go to step 7 .
6. Inspect Black/White wire between terminal No. 1 of connector C-37 and
terminal No. 2 of ignition switch connector C-308, including junction block
connectors C-211 and C-215. See Fig. 22
. If wire is okay, go to next step. If
wire is not okay, repair as necessary. See WIRE REPAIR
. Go to step 10 .
7. Inspect SRS ECU connector C-26. See SRS ELECTRONIC CONTROL
UNIT (SRS ECU)
under REMOVAL & INSTALLATION. If SRS ECU
connector C-26 is connected correctly, go to next step. If SRS ECU connector
C-26 is not connected correctly, properly connect connector. Go to step 10 .
8. Check Blue/Yellow wire between connector C-37, terminal No. 3 and SRS
ECU connector C-26, terminal No. 21, for damage, shorts or open circuits. See
Fig. 33
. If wire is okay, go to next step. If wire is not okay, repair as
necessary. Go to step 10 .
9. Disconnect negative battery cable. Disconnect SRS ECU connector C-26.
Connect negative battery cable. Connect a jumper wire between ground and
SRS ECU connector C-26, terminal No. 21. If PASSENGER AIR BAG OFF
warning light does not illuminate, replace PASSENGER AIR BAG OFF
warning light assembly. Go to next step. If PASSENGER AIR BAG OFF
warning light illuminates, erase, then retrieve DTCs. If DTC B1489 is
retrieved, replace SRS ECU. Go to next step.
10. Reconnect all SRS components. Activate air bag system. Using scan tool,
retrieve DTCs. If DTC B1489 is retrieved, go to step 1 . If DTC B1489 is not
retrieved, s
ystem is normal at this time.
2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems
STARTER MOTOR DOES NOT STOPCheck the magnetic switch. ON-VEHICLE TESTING STARTER MOTOR DOES NOT OPERATE 1. Is the battery in good condition? If Yes, go to the next step. If No, then charge
or replace battery.
2. Disconnect the starter motor "S" (solenoid) terminal connector. Using a jumper
wire, apply battery positive voltage to starter motor "S" (solenoid) terminal.
Does starter motor operate normally? If Yes, then check ignition switch,
transmission range switch and the line between the battery and starter motor
"S" (solenoid) terminal. If No, then go to the next step.
3. Check if the cable between starter "B" (battery) terminal and battery positive
terminal for connection and continuity. Is the starter cable in good condition? I
f
Yes, then go to the next step. If No, then repair or replace the cable.
4. Check the connection and continuity of the cable between starter motor body
and the negative battery terminal. Is the ground line in good condition? If Yes,
then go to the next step. If No, then repair or replace cable.
5. Is the starter motor in good condition? If Yes, problem is excessive rotational
resistance of the engine. If No, then replace the starter motor.
BENCH TESTING MAGNETIC SWITCH PULL-IN TEST 1. Disconnect field coil wire from "M" terminal of the magnetic switch. See Fig.
3 . WARNING:Battery posts, terminals and related accessories
contain lead and lead compounds. Wash hands after
handling.
CAUTION: To prevent coil from burning, DO NOT apply voltage
to starter assembly for more than 10 seconds.
2004 Mitsubishi Endeavor Limited
2004 STARTING & CHARGING SYSTEMS Starters - Endeavor
