2004 MITSUBISHI ENDEAVOR wiring

Install the engine assembly, being careful not to pinch the cables, hoses or wiring
harness connectors.
Fig. 36: Installing Engine Assembly

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
>>B<< ENGINE MOUNT INSTALLATION 1. Place a garage jack against the engine oil pan with a piece of wood in between,
and install the engine mount while adjusting the position of the engine.
2. Support the engine assembly with a garage jack.
3. Remove the chain block.
4. < Engine hanger MB991895 is used >
1. Set special tool MB991895 to the front fender assembling bolts (A and B)
and
(C and D
) as shown.

2004 Mitsubishi Endeavor Limited
2004 ENGINE Engine - Endeavor

TROUBLESHOOTING HINTS
Damaged wiring harness or connector. Malfunction of the radio and CD player or radio, CD player and CD changer.
DIAGNOSIS Required Special Tool:
MB991223: Harness set
STEP 1. Check to see that the radio and CD player or radio, CD player
and CD changer is energized when the power switch is turned ON.
1. Turn the ignition switch to "ACC" position.
2. Turn ON the radio and CD player or radio, CD player and CD changer
power switch.
Q: Is the radio and CD player or radio, CD player and CD changer
energized when the power switch is turned ON?
YES: Go to Step 2.
NO: Go to Step 5 .
STEP 2. Check radio and CD player or radio, CD player and CD changer
connector C-105 for loose, corroded or damaged terminals, or terminals pushed back in the connector
.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 8: Identifying Connector C
-105

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are radio and CD player or radio, CD player and CD changer
connector C-105 in good condition?
YES: Go to Step 3.
NO: Repair or replace the damaged component(s). If the power switch is
turned on, the radio and CD player or radio, CD player and CD changer
should operate normally.
STEP 3. Check the wiring harness between radio and CD player or radio,
CD player and CD changer connector C-105 (terminal 20) and the i
gnition
switch (ACC).

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Q: Is the wiring harness between radio and CD player or radio, CD player
and CD changer connector C-105 (terminal 20) and ignition switch (ACC)
in good condition?
YES: Go to Step 4.
NO: Repair the wiring harness. If the power switch is turned on, the radio
and CD player or radio, CD player and CD changer should operate
normally.
STEP 4. Check the installation condition of the radio and CD player or
radio, CD player and CD changer.
Q: Are the radio and CD player or radio, CD player and CD changer
installed correctly?
YES: Repair or replace the radio and CD player or radio, CD player and
CD changer. If the power switch is turned on, the radio and CD player or
radio, CD player and CD changer should operate normally.
NO: Install the radio and CD player or radio, CD player and CD changer
properly. If the power switch is turned on, the radio and CD player or
radio, CD player and CD changer should operate normally.
STEP 5. Measure at radio and CD player or radio, CD player and CD
changer connector C-105 in order to check the battery circuit of power
supply system to the radio and CD player or radio, CD player and CD
changer (ignition switch ACC).
1. Disconnect radio and CD player or radio, CD player and CD changer
connector
C-105, and measure at the wiring harness side.
NOTE: The radio and CD player or radio, CD player and CD
changer are grounded to the instrument panel center
reinforcement directly.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 13: Identifying CD Changer Connector C
-105

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are radio and CD player or radio, CD player and CD changer
connector C-105 in good condition?
YES: Go to Step 7.
NO: Repair or replace the damaged component(s). If the power switch is
turned on, the radio and CD player or radio, CD player and CD changer
should operate normally.
STEP 7. Check the wiring harness between radio and CD player or radio,
CD player and CD changer connector C-105 (terminal 20) and ignition
switch (ACC).

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Q: Is the wiring harness between radio and CD player or radio, CD player
and CD changer connector C-105 (terminal 20) and ignition switch (ACC)
in good condition?
YES: There is no action to be taken.
NO: Repair the wiring harness. If the power switch is turned on, the radio
and CD player or radio, CD player and CD changer should operate
normally.
STEP 8. Check the installation condition of the radio and CD player or
radio, CD player and CD changer.
Q: Are the radio and CD player or radio, CD player and CD changer
installed correctly?
YES: Replace the radio and CD player or radio, CD player and CD
changer. If the power switch is turned on, the radio and CD player or
radio, CD player and CD changer should operate normally.
NO: Install the radio and CD player or radio, CD player and CD changer
properly. If the power switch is turned on, the radio and CD player or
radio, CD player and CD changer should operate normally.
INSPECTION PROCEDURE 2: When Remote Controlled Radio Power Switch is Turned "ON," no Power is Available.
But Radio, CD Player and CD Changer Power Switch is Available. < vehicles with seven speakers >.
NOTE: The radio and CD player or radio. CD player and CD
changer are grounded to the instrument panel center
reinforcement directly.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

change on the voltage. You can switch on/off the audio unit, control the mode
and volume by the remote controlled radio switch (RH). You can select a CD
track and pre-set radio station, and tune it by the remote controlled radio switch
(LH).
TECHNICAL DESCRIPTION (COMMENT) If the system does not recognize the remote controlled radio switches (RH), the
clock spring or the radio, CD player and CD changer may be defective. TROUBLESHOOTING HINTS
Malfunction of the remote controlled radio switch (RH) Malfunction of the radio, CD player and CD changer Malfunction of the clock spring Damaged wiring harness or connectors
DIAGNOSIS Required Special Tool:
MB991223: Harness set
STEP 1. Measure the voltage at remote controlled radio switch power
supply circuit at the clock spring connector C-306.
1. Disconnect the clock s
prin
g connector
C-306.
NOTE: You can switch on the audio unit by the remote controlled
switch, but can not switch it off.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 20: Identifying Connector C
-306

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are radio, CD player and CD changer connector C-110 and clock
spring connector C-306 in good condition?
YES: Go to Step 3.
NO: Repair or replace the damaged component(s). The remote controlled
radio switch should work normally.
STEP 3. Check the wiring harness between clock spring connector C-306
(terminal 2) and radio, CD player and CD changer connector C-110
(terminal 5
).

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor