Page 972 of 3870
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
Fig. 101: Data List Reference Table (2 Of 2)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
PCM TERMINAL VOLTAGE REFERENCE CHART FOR AUTO-CRUISE CONTROL SYSTEM
OPERATION 1. Disconnect the PCM connectors, and connect special tool MB991923 in
between.
2. Measure the voltage between each check connector terminals of special tool
MB991923 and
ground terminals 63 or 76.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 973 of 3870
Fig. 102: Identifying Special Tool
-Power Plant ECU Check Harness Connector
(Component Side)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig. 103: Auto Cruise Control System Operation Table (1 Of 2)
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 974 of 3870
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
Fig. 104: Auto Cruise Control System Operation Table (2 Of 2)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
ON-VEHICLE SERVICE AUTO-CRUISE CONTROL MAIN SWITCH CHECK 1. Turn the i
gnition to the "ON"
position.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 982 of 3870
Fig. 111: Identifying Condition Table
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
TRANSMISSION RANGE SWITCH ("N" POSITIN) Refer to ESSENTIAL SERVICE
.
THROTTLE POSITION SENSOR Refer to THROTTLE ACTUATOR CONTROL MOTOR CHECK
.
AUTO-CRUISE CONTROL SWITCH CHECK 1. Remove the auto-cruise control switch. (Refer to AUTO
-CRUISE
CONTROL
).
2. Measure the resistance between terminal 2 and terminal 3 when each of the
"COAST/SET", "ACC/RES", "CANCEL" and "CRUISE" (MAIN) switches is
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 983 of 3870
pressed. If the values measured at the time correspond to those in the table below, the resistance values are correct.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 985 of 3870
Fig. 112: Checking Auto Cruise Control Switc
h
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig. 113: Identifying Switch Position And Specified Condition Table
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
AUTO-CRUISE CONTROL REMOVAL AND INSTALLATION
WARNING:Before removal of the air bag module, refer to AIR
BAG SAFETY PRECAUTIONS
and DRIVER
-SIDE AIR
BAG MODULE & CLOCKSPRING
.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 1068 of 3870
2 .
3. Turn the ignition switch to the ON position and select BELT TENSION
MEASUREMENT from the menu screen on Scan Tool (MB991958).
4. Hold Microphone (part of Belt Drive Meter Set) (MB991668) near the center
of the drive belt between the pulleys away from the rear surface of the belt and
perpendicular to the belt (no more then 15 degrees in either direction). See Fi
g.
3 and Fig. 4
.
5. Gently tap the middle of the belt between the pulleys with your finger, and
check that the vibration frequency of the belt is within specification. See Fig. 3
and Fig. 4
. See DRIVE BELT ADJUSTMENT SPECIFICATIONS
table.
CAUTION: Temperature of the surface of the belt should be
as close possible to underhood temperature.
CAUTION: DO NOT let contaminants such as water or oil get
onto the microphone. If strong gusts of wind
blow against the microphone or if there are any
loud sources of noise nearby, the values
measured by the microphone may not
correspond to actual values. DO NOT take
measurement while engine is running.
2004 Mitsubishi Endeavor Limited
2004 ENGINE COOLING Specifications & Drive Belt Routing - Endeavor
Page 1071 of 3870
Fig. 4: Checking Vibration Frequency (Power Steering Pump Belt)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Using Tension Gauge Use a belt tension gauge to check that the belt tension is within specification. See
Fig. 5
an
d Fig. 6
. See DRIVE BELT ADJUSTMENT SPECIFICATIONS
table.
2004 Mitsubishi Endeavor Limited
2004 ENGINE COOLING Specifications & Drive Belt Routing - Endeavor
