2004 MITSUBISHI ENDEAVOR clock

2. Adjust the belt vibration frequency, tension, or deflection amount using the
adjusting bolt according to specifications. See Fig. 10
. See DRIVE BELT
ADJUSTMENT SPECIFICATIONS
table.
3. Tighten the lock nut to 29-43 ft. lbs. See Fig. 10
.
4. Tighten the adjusting bolt to 35-53 INCH lbs. (4-6 N.m). See Fig. 10
.
5. Check the belt vibration frequency, tension, or deflection and readjust as
necessary. See DRIVE BELT ADJUSTMENT SPECIFICATIONS table.
Fig. 10: Adjusting Power Steering Pump Drive Belt

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
DRIVE BELT ROUTIN
G
CAUTION: Check after turning the crankshaft one or more
rotations clockwise.

2004 Mitsubishi Endeavor Limited
2004 ENGINE COOLING Specifications & Drive Belt Routing - Endeavor

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
3. Replace the radiator cap if the reading does not remain at or above the limit.
ENGINE COOLANT REPLACEMENT 1. Drain the water from the radiator, heater core and engine after unplugging the
radiator drain plug and removing the radiator cap.
2. Drain the water in the water jacket by unplugging the drain plug of the cylinder
block. For the right bank side on AWD vehicles, drain the engine coolant from
the water feed tube assembly of the transfer box.
3. Remove the radiator condenser tank assembly and drain the coolant.
4. Drain the coolant then clean the path of the coolant by injecting water into the
radiator from the radiator cap area.
WARNING:When removing the radiator cap, use care to avoid
contact with hot coolant or steam. Place a shop
towel over the cap and turn the cap
counterclockwise a little to let the pressure escape
through the vinyl tube. After relieving the steam
pressure, remove the cap by slowly turning it
counterclockwise.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Cooling - Endeavor

1. Install special tool MD998769 and the crankshaft pulley washer, and then
tighten the crankshaft bolt.
2. Align the timing mark on the crankshaft sprocket with the timing mark on the
oil pump case, and then rotate the sprocket three teeth counterclockwise.
Fig. 24: Aligning The Timing Mark On Crankshaft Sprocket & Timing
Mark On Oil Pump Case

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Align the timing mark on the left bank camshaft sprocket with the timing mark
on the rocker cover.
4. Align the timing mark on the right bank camshaft sprocket with the timing
mark on the rocker cover.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Fig. 29: Checking Timing Marks Of All The Sprockets Are In Alignment

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
9. Rotate the crankshaft a quarter turn counterclockwise. Then rotate it back
clockwise to verify that all the timing marks are aligned.
10. Loosen the flange bolt securing the tensioner pulley, and then mount special
tool MD998767 and a torque wrench on the tensioner pulley.
11. Torque it to 4.4 N.m (39 in-lb) with the torque wrench.
12. While holding the tensioner pulley in position, tighten the flange bolt to the
specified torque.
Ti
ghtenin
g tor
que: 48+
/-6 N.m (35+
/-4 f
t-lb)

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Fig. 30: Holding The Tensioner Pulley In Position, Tighten The Flange Bolt

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
13. Rotate the crankshaft two turns clockwise and leave it alone for approximately
five minutes.
14. Check to see whether the metal wire inserted when the auto-tensioner was
installed can be removed without any resistance.
If the metal wire can be removed without any resistance, it means that the belt
has a proper tension. Therefore, remove the metal wire. In this condition, check
that the rod protrusion of the auto-tensioner is within the standard value.
Standard value: 4.8 - 6.0 mm (0.19 - 0.24 inch)

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Fig. 17: Loosening Tensioner Pulley Lock Nut

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Adjust the belt tension to the standard value by turning the adjusting bolt. The
tension will increase when turning the adjusting bolt clockwise, and decrease
when turning counterclockwise.
3. Tighten the lock nut to the specified torque.
Tightening torque: 49+/-9 N.m (36+/-7 ft-lb)
4. Tighten the adjusting bolt.
Tightening torque: 5.0+/-1.0 N.m (44+/-9 in-lb)
5. Check the belt deflection amount and tension, and readjust if necessary.
IGNITION TIMING CHECK
CAUTION: Check after turning the crankshaft one or more
rotations clockwise.

2004 Mitsubishi Endeavor Limited
2004 ENGINE Engine - Endeavor

Fig. 87: Removing Crankshaft Pulley From Crankshaft

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
<< B >> TIMING BELT REMOVAL 1. Turn the crankshaft clockwise to align each timing mark and to set the number
1 c
ylinder to com
pression to
p dead center.
CAUTION: Never turn the crankshaft counterclockwise.

2004 Mitsubishi Endeavor Limited
2004 ENGINE Engine - Endeavor

Fig. 88: Turning Crankshaft Clockwise To Align Each Timing Mark And To Set Number 1 Cylinder

2004 Mitsubishi Endeavor Limited
2004 ENGINE Engine - Endeavor