2004 MITSUBISHI ENDEAVOR clock

Fig. 46: Identifying Connector C
-303 C
-311

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are the wiring harness between remote controlled radio switch
connector C-311 (terminals 1 and 2) and clock spring connector C-303
(terminals 4 and 5) in good condition?
YES: No action to be taken.
NO: Repair the wiring harness. The remote controlled radio switch (LH)
should work normally.
INSPECTION PROCEDURE 5: No Sound. < Vehicles with Audio Amplifier >.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 30: Removing & Installing Stabilizer Bar (1 Of 2)

Courtes
y of MITSUBISHI MOTOR SALES OF AMERICA
.
module assembly, refer to AIR BAG SAFETY PRECAUTIONS
and DRIVER
-SIDE AIR BAG
MODULE & CLOCKSPRING
. Also, put the front
wheels in straight-ahead position. Failure to do
so may damage the SRS clock spring and render
the SRS air bag inoperative, which results
serious driver injury.
*: Indicates parts which should be temporarily
tightened, and then fully tightened with the
vehicle on the ground in an unladen condition.

2004 Mitsubishi Endeavor LS 2004 SUSPENSION Front - Endeavor

To disconnect the suction hose from the suction flexible hose, lift the lug on the
suction pipe and twist the suction flexible hose union counterclockwise.
Plug the hose nipple to prevent entry of dust and dirt. Fig. 311: Disconnecting Suction Pipe

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

INSTALLATION SERVICE POINT >> A << SUCTION HOSE INSTALLATION When replacing the suction hose, refill them with a specified amount of compressor
oil, and then install them.
moisture absorbent, use a non-porous material to
plug the hose and nipples.

2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor

Fig. 120: Removing Steering Column Upper/Lower Cover

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
< < B > > STEERING LOCK CYLINDER REMOVAL 1. Insert the key in the steering lock cylinder and turn it to the "ACC" position.
2. Using a small Phillips head screwdriver, pull the steering lock cylinder toward
you.
Fig. 121: Removing Steering Lock Cylinder

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL AND INSTALLATION < FROM TO JANUARY 2004 >
WARNING:
Before removing the steering wheel, air bag
module assembly and clock spring refer to AIR BAG RESTRAINT SYSTEMS
).

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 4: Identifying Clip And Claw Positions On Instrument Panel

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL SERVICE POINT << A >> CONNECTOR DISCONNECTION Disconnect the connectors shown in the illustration.
1. CLOCK SPRING CONNECTOR
(6)

2004 Mitsubishi Endeavor XLS
2004 BODY & ACCESSORIES Instrument Panel Assembly - Endeavor

2. CLOCK SPRING CONNECTOR (4-Y)
3. COLUMN SWITCH CONNECTOR (10)
Fig. 5: Disconnecting Connectors

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
4. AIR BAG MODULE
(FRONT PASSENGER'S SIDE CONNECTOR
(2-R
)

2004 Mitsubishi Endeavor XLS
2004 BODY & ACCESSORIES Instrument Panel Assembly - Endeavor

5. Loosen the two lower steering column mounting bolts by two turns.
6. If there is any sign of looseness when the moveable bracket is moved back and
forth by hand, replace the steering column shaft assembly with a new one.
7. If no problem is found during the inspection, tighten the steering column
mounting bolts to the specified torque.
Tightening torque: 12 +/- 2 N.m (102 +/- 22 in-lb) STEERING WHEEL REMOVAL AND INSTALLATION Post-installation Operation
Checking Steering Wheel Position with Wheels Straight Ahead
WARNING:
Before removing the steering wheel and air bag
module assembly, refer to AIR BAG SAFETY PRECAUTIONS
and DRIVER
-SIDE AIR BAG
MODULE & CLOCKSPRING
or PASSENGER
-
SIDE AIR BAG MODULE
.
When removing and installing the steering
wheel, do not let it bump against the air bag
module.

2004 Mitsubishi Endeavor LS
2004 STEERING Power Steering - Endeavor

Fig. 28: Removing Steering Wheel

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL SERVICE POINT << A>> AIR BAG MODULE ASSEMBLY REMOVAL 1. Slide section A of the clock spring connector in the arrow direction shown in
illustration, and disconnect the connector.
2. Loosen the Torx screw and remove the air ba
g module assembl
y.

2004 Mitsubishi Endeavor LS
2004 STEERING Power Steering - Endeavor