2004 MITSUBISHI ENDEAVOR Rear end

2. If the dust cover is cracked or damaged, replace the stabilizer bar link
assembly. REAR SUSPENSION CROSSMEMBER REMOVAL AND INSTALLATION < FWD>
NOTE: Cracks or damage of the dust cover may cause damage
to the ball joint.
CAUTION: For vehicles with ABS, be careful when handling the
pole piece at the tip of the ABS sensor so as not to
damage it by striking against other parts.

2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor

Fig. 33: Removing & Installing Rear Suspension Crossmember (FWD)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL SERVICE POINTS << A>> REAR ABS SENSOR REMOVAL < VEHICLES WITH ABS> The rear ABS sensor can be damaged during service work. Unclamp the rear ABS
sensor cable as shown, and tie it out of the wa
y.
CAUTION: For vehicles with ABS, be careful when handling the
pole piece at the tip of the ABS sensor so as not to
damage it by striking against other parts.

2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor

Fig. 34: Removing Rear ABS Sensor Cable

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
<< B>> TOE CONTROL ARM ASSEMBLY REMOVAL Disconnect the toe control arm only from its rear suspension crossmember side, and
tie it to the trailin
g arm assembl
y as shown.

2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor

Fig. 35: Removing Toe Control Arm Assembly

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
<< C>> CROSSMEMBER STAY REMOVAL The crossmember mounting bolts need not be unscrewed when the crossmember
stay is replaced. However, the bolts may be loose while the crossmember stay is
removed. It is recommended that you should retighten the bolts to 100 +/- 10 N.m (74 +
/- 7 f
t-lb
).

2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor

Fig. 36: Removing Crossmember Stay

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSTALLATION SERVICE POINTS >>A<< CROSSMEMBER STAY INSTALLATION Install the crossmember stay with its arrow facing the front of vehicle.
2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor

Fig. 37: Installing Crossmember Stay

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
>>B<< CROSSMEMBER STAY/CROSSMEMBER NUT INSTALLATION Ensure that the crossmember mounting bolts have been tightened to 90 - 110 N.m (67 - 81 f
t-lb
), and then install the crossmember sta
y with the crossmember nut.

2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor

Fig. 38: Installing Crossmember Stay/Nut

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL AND INSTALLATION < AWD>
CAUTION: For vehicles with ABS, be careful when handling the
pole piece at the tip of the ABS sensor so as not to
damage it by striking against other parts.

2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor

Fig. 39: Removing & Installing Rear Suspension Crossmember (AWD)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL SERVICE POINTS << A>> REAR ABS SENSOR REMOVAL < VEHICLES WITH ABS>
CAUTION: For vehicles with ABS, be careful when handling the
pole piece at the tip of the ABS sensor so as not to
damage it by striking against other parts.

2004 Mitsubishi Endeavor LS 2004 SUSPENSION Rear - Endeavor