2004 MITSUBISHI ENDEAVOR service

Fig. 70: Connecting Terminal 1 To Ground

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Does only the immobilizer indicator light illuminate? (other indicator
lights are in good condition)
YES: Replace the immobilizer-ECU. Then register the password (secret
code) and encrypted code ON
-VEHICLE SERVICE
.
NO: Go to Step 3.
STEP 3. Check immobilizer-ECU connector C-310-1 and combination
meter connector C-102 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Q: Is the wiring harness between combination meter connector C-102
(terminal 1) and the battery in good condition?
YES: Go to Step 8.
NO: Repair the wiring harness. Check to see that all meters operate.
STEP 8. Retest the system.
Q: Is the malfunction eliminated?
YES: The procedure is complete. (If no malfunctions are found in all
steps, an intermittent malfunction is suspected. Refer to HOW TO USE
TROUBLESHOOTING/ INSPECTION SERVICE POINT
).
NO: Go to Step 1.
INSPECTION PROCEDURE 4: The Immobilizer Indicator Light does not Illuminate. < FROM TO JANUARY 2004 >
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 84: Checking Connector C
-39
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Does only the immobilizer indicator light illuminate? (other indicator
lights are in good condition)
YES: Replace the immobilizer-ECU. Then register the password (secret
code) and encrypted code ON
-VEHICLE SERVICE
.
NO: Go to Step 3.
STEP 3. Check immobilizer-ECU connector C-39 and combination meter
connector C-102 for loose, corroded or damaged terminals, or terminals
pushed back in the connector.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Q: Is the wiring harness between combination meter connector C-102
(terminal 1) and the battery in good condition?
YES: Go to Step 8.
NO: Repair the wiring harness. Check to see that all meters operate.
STEP 8. Retest the system.
Q: Is the malfunction eliminated?
YES: The procedure is complete. (If no malfunctions are found in all
steps, an intermittent malfunction is suspected. Refer to HOW TO USE
TROUBLESHOOTING/ INSPECTION SERVICE POINT
).
NO: Replace the combination meter.
DATA LIST REFERENCE TABLE Fig. 94: Data List Reference Table

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
CHECK AT IMMOBILIZER-ECU < UP TO DECEMBER 2003 > TERMINAL VOLTAGE CHEC
K

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 98: Special Tool Table (2 Of 2)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
ON-VEHICLE SERVICE HOW TO REGISTER ENCRYPTED CODE Required Special Tools:
MB991 958: Scan Tool (MUT-III Sub Assembly)
MB991 824: Vehicle Communication Interface (V.C.I.) MB991 827: MUT-III USB Cable MB991 910: MUT-III Main Harness A (Vehicles with CAN
communication system)
If the ignition key, immobilizer-ECU, PCM is replaced encrypted codes of all the
ignition keys must be registered. (A maximum of eight different ignition key can be CAUTION: Because registering the encrypted codes is done
after all previously-registered codes have been
erased, you should keep all of the ignition keys that
have already been registered accessible.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 118: Identifying TP Lock Check Table

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
IGNITION SWITCH REMOVAL AND INSTALLATION < UP TO DECEMBER 2003 > Fig. 119: Removing/Installing Ignition Switch

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL SERVICE POINTS
< < A > > STEERING COLUMN UPPER COVER/STEERING COLUMN LOWER COVER REMOVAL 1. Rotate the steering wheel with a slightly from side-to-side to access and
remove the mountin
g screws.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 122: Removing/Installing Ignition Switch

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL SERVICE POINTS
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 1: Ignition System Circuit Diagram

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
SPECIAL TOOLS Fig. 2: Identifying Special Tool

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
ON-VEHICLE SERVICE KNOCK CONTROL SYSTEM CHECK Check the knock sensor circuit if diagnostic trouble code, No. P0325 is shown.
Refer to DTC P0325: KNOCK SENSOR CIRCUIT MALFUNCTION
.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Ignition System - Endeavor