Page 1821 of 3870
Fig. 163: Removing Amplifier
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSTALLATION SERVICE POINTS >>A<< AMPLIFIER INSTALLATION Install while ali
gnin
g with the am
plifier mountin
g hole.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor
Page 1844 of 3870
Fig. 14: Removing & Installing Rear Display Unit (Overhead Type)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL SERVICE POINT << A >>REAR DISPLAY UNIT (OVERHEAD TYPE) ASSEMBLY REMOVAL
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Video Entertainment System - Endeavor
Page 1847 of 3870
DISASSEMBLY AND ASSEMBLYFig. 2: Disassembly/Assembly Of Floor Console
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
DISASSEMBLY SERVICE POINT << A >> RIVETS REMOVAL Use a drill [4.0 mm (0.16 inch)] to make a hole in the rivet to break it, and then
remove the rivet.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Floor Console Assembly - Endeavor
Page 1848 of 3870
Fig. 3: Removing Rivet
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
ASSEMBLY SERVICE POINT >>A<< RIVET INSTALLATION 1. Insert rivets into the bracket and duct.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Floor Console Assembly - Endeavor
Page 1853 of 3870
MB991897: Ball Joint Remover
REMOVAL SERVICE POINTS << A>> DRIVE SHAFT NUT REMOVAL Use special tool MB990767 to fix the hub and remove the drive shaft nut.
CAUTION: Do not apply pressure to wheel bearing by the
vehicle weight to avoid possible damage when drive
shaft nut is loosened.
2004 Mitsubishi Endeavor LS
2004 DRIVELINE/AXLES Front Axle Hub & Axle Shafts - Endeavor
Page 1859 of 3870
Fig. 7: Pulling Out Front Wheel Hub From Knuckle Using Special Tools
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSTALLATION SERVICE POINT << A>> WASHER/DRIVE SHAFT NUT INSTALLATION 1. Be sure to install the drive shaft washer in the specified direction.
2. Usin
g special tool MB990767
, tighten the drive sha
ft nut to the s
pecified
CAUTION: Before securely tightening the drive shaft nuts, make
sure there is no load on the wheel bearings.
Otherwise the wheel bearings will be damaged.
2004 Mitsubishi Endeavor LS
2004 DRIVELINE/AXLES Front Axle Hub & Axle Shafts - Endeavor
Page 1865 of 3870
Fig. 14: Removing Drive Shaft Assembly (AWD)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL SERVICE POINTS << A>> DRIVE SHAFT NUT REMOVAL Use special tool MB990767 to fix the hub and remove the drive shaft nut.
CAUTION: Do not apply pressure to the wheel bearing by the
vehicle weight to avoid possible damage when the
drive shaft nut is loosened.
2004 Mitsubishi Endeavor LS
2004 DRIVELINE/AXLES Front Axle Hub & Axle Shafts - Endeavor
Page 1874 of 3870
Fig. 23: Removing Output Shaft Using Special Tool MB991721
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSTALLATION SERVICE POINTS >>A<< OUTPUT SHAFT < AWD> /DRIVE SHAFT/DRIVE SHAFT AND INNER SHAFT ASSEMBLY < FWD-RH>
INSTALLATION
>>B<< DRIVE SHAFT NUT INSTALLATION 1. Be sure to install the drive shaft washer in the specified direction.
CAUTION: When installing the output shaft, the drive shaft or
the drive shaft and inner shaft assembly, be careful
that the spline part of the output shaft, the drive shaft
or the drive shaft and inner shaft assembly do not
damage the oil seal.
CAUTION: Before securely tightening the drive shaft nuts,
make sure there is no load on the wheel
bearings. Otherwise the wheel bearing will be
2004 Mitsubishi Endeavor LS
2004 DRIVELINE/AXLES Front Axle Hub & Axle Shafts - Endeavor
