2004 MITSUBISHI ENDEAVOR oil

Fig. 104: Installing Oil Pan To Bottom Of Cylinder

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
4. Tighten the upper oil pan bolts in the sequence shown.
Tightening torque: 9.0+/-3.0 N.m (80+/-26 in-lb)
Fig. 105: Tightening Upper Oil Pan Bolts

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
>>G<< OIL PAN, LOWER INSTALLATION 1. Clean both gasket surfaces of the upper and lower oil pans.
2. Apply a 4 mm (0.2 inch) diameter bead of sealant (Mitsubishi Genuine Parts
number MD970389 or e
quivalent
) to the lower oil
pan.
NOTE: After installation, keep the sealed area away from the oil
and coolant for approximately one hour.
2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Apply sealant as indicted by the broken line in the illustration; the grooves
must be traced and the bolt holes must be surrounded with a bead of sealant.
3. Install the lower oil pan to the upper oil pan. NOTE: Be sure to install the oil pan quickly while the sealant is
wet (within 15 minutes).

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Fig. 106: Identifying Bolt Hole And Groove And Install The Lower Oil Pan To The Upper Oil Pan

Courtes
y of MITSUBISHI MOTOR SALES OF AMERICA
.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

4. Tighten the lower oil pan bolts in the sequence shown.
Tightening torque: 11+/-1 N.m (95+/-9 in-lb)
Fig. 107: Identifying Lower Oil Pan Bolts In Standard Sequence

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
>>H<< DRAIN PLUG GASKET INSTALLATION NOTE: After installation, keep the sealed area away from oil for
approximately one hour.
2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Install the drain plug gasket in the direction shown.
CAUTION: If the gasket is installed in the wrong direction, oil
leaks will occur.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Fig. 108: Installing Drain Plug Gaske
t
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSPECTION OIL PUMP 1. Check the tip clearance.
Standard value: 0.06 - 0.18 mm (0.003 - 0.007 inch)
Fig. 109: Checking Tip Clearance

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Check the side clearance.
Standard value: 0.04 - 0.10 mm (0.002 - 0.003 inch)

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Fig. 116: Identifying Piston Pin Size Chart

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Heat the piston to approximately 70°C (158°F).
NOTE: The piston size mark shows on the top of the piston.
CAUTION: Appl
y ample coat of en
gine oil to the peripher
y of
the piston pin and the hole of the connecting rod
small end. The clearance between the piston and
the piston pin is a tight fit at room temperature.
Therefore, be sure to heat the piston before
inserting the piston pin. Use care since the
piston is hot after heating.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Fig. 119: Checking Piton Moves Smoothly

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
>>B<< OIL RING INSTALLATION 1. Fit the oil ring spacer into the piston ring groove.
2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor