Page 2579 of 3870
Fig. 46: Measuring Voltage Between Terminal 1 And Ground
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the measured voltage approximately 12 volts (battery positive
voltage)?
YES: Go to Step 5.
NO: Go to Step 3.
STEP 3. Check immobilizer-ECU connector C-39 and MFI relay
connector B-15X for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor
Page 2613 of 3870
Fig. 74: Check Wiring Harness Between Combination Meter Connector C-102
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig. 75: Checking Connector C
-301
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the wiring harness between combination meter connector C-102
(terminal 1) and the battery in good condition?
NOTE: Also check key reminder switch connector C-310 for
loose, corroded, or damaged terminals, or terminals
pushed back in the connector. If key reminder switch
connector C-310 is damaged, repair or replace it.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor
Page 2619 of 3870
Fig. 78: Checking Combination Meter Connector C
-102 For Loose
Corroded Or Damaged Terminals
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is combination meter connector C-102 in good condition?
YES: Go to Step 7.
NO: Repair or replace the damaged component(s). Check to see that all
meters operate.
STEP 7. Check the wiring harness between combination meter connector
C-102 (terminal 1) and the battery.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor
Page 2621 of 3870
Fig. 79: Checking Wiring Harness Between Combination Meter Connector C
-102 And Battery
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
NOTE: Also check intermediate connector C-31 and joint
connector C-04 for loose, corroded, or damaged
terminals, or terminals pushed back in the connector. If
intermediate connector C-31 or joint connector C-04 is
damaged, repair or replace it.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor
Page 2640 of 3870
Fig. 92: Checking Wiring Harness Between Combination Meter Connector C
-102 And Battery
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
NOTE: Also check intermediate connector C-31 and joint
connector C-04 for loose, corroded, or damaged
terminals, or terminals pushed back in the connector. If
intermediate connector C-31 or joint connector C-04 is
damaged, repair or replace it.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor
Page 3092 of 3870
Fig. 4: Checking Continuity Between Terminals
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Check that the indicator is lighted at HI or LO when battery voltage is supplied
to terminal 5 and terminal 8 is grounded.
3. Check that indicator is lighted when battery voltage is supplied to terminals 2
and terminal 6.
SEAT CUSHION HEATER CHECK Measure the resistance between terminals.
Standard value: At room tem
perature 20 °C (68 °F)
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Front & Rear Seat Assembly - Endeavor
Page 3249 of 3870
Q: Is the voltage approximately 12 volts (battery positive voltage)?
YES: Go to Step 5.
NO: Go to Step 4.
STEP 4. Check TCL/ASC-ECU connector A-32 for loose, corroded or
dama
ged terminals, or terminals
pushed back in the connector
.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3267 of 3870
Q: Is the voltage approximately 12 volts (battery positive voltage)?
YES: Go to Step 5.
NO: Go to Step 4.
STEP 4. Check TCL/ASC-ECU connector A-32 for loose, corroded or
dama
ged terminals, or terminals
pushed back in the connector
.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
