2004 ISUZU TF SERIES fuse

8A-170 ELECTRICAL-BODY AND CHASSIS
BACKUP LIGHT
1. Backup light does not light on one side (RH or LH)

Checkpoint Trouble Cause Countermeasure

Repair grounding point contactPoor ground contact NGGrounding point
Replace the bulb or repair
connector contactBackup light bulb continuityBurned out bulb or poor
connector contact NG
OK



2. Backup light does not light on both sides



Repair or replace the switch

Poor switch point contact of
faulty switch
NG
Voltage between 5 F-6
(5
F-5 ) - ground with
starter switch ON and shift
lever into reverse position
(Should be battery voltage
present)

Back up light switch (mode
switch) continuity


Reinstall or replace fuse No.
C-4 (15A)

Fuse No. C-4 (15A, Fuse box)

Poor fuse contact or blown
fuse
NG
OK OK

Repair open circuit or
connector contact

Open circuit or poor connector
contact
NG

ELECTRICAL-BODY AND CHASSIS 8A-171
HORN
1. Both sides of horn do not sound

Checkpoint Trouble Cause Countermeasure



Repair the grounding point

Poor ground contact
NG

Horn relay


Grounding point


Reinstall or replace fuse No.
EB-15 (10A)

Fuse No EB-15 (10A, Relay
and fuse box)

Poor fuse contact or blown
fuse
NG
OK OK

Reinstall or replace the horn
relay

Poor relay contact or faulty
horn relay
NG
Voltage between connector
3
X-3 - ground or 1 X-3
- ground (Should be battery
voltage present) OK

Repair open circuit or
reconnect the connector
Open circuit or poor connector
contact between fuse No. EB-
15 (10A) and horn relay
NG

Remove steering pad and
steering wheel
OK

Horn switch continuity
OK
Repair or replace the horn
switch

Poor switch point contact or
faulty switch
NG
Continuity between
4
X-3 - 10 B-60
2
X-3 - 1 C-20 (1 C-21) OK

Repair open circuit or
connector contact

Open circuit or poor connector
contact
NG

ELECTRICAL-BODY AND CHASSIS 8A-195
INSPECTION AND REPAIR




R-9 R-10
R-1 R-6



DOOR SWITCH
Door Switch Connections

Connector
SW No.
R-9 R-10
R-1 R-6
position Terminal No.
1 Body Ground
PUSHED
RELEASED





WARNING BUZZER
1. Warning Buzzer Circuit


Warning function Operational conditions
Taillights left on The buzzer sounds when both the tail relay and the FRT door switch-drive
side are turned on. To stop the sound of the buzzer, turn on the starter
switch.




Harness side
B-45


2. Warning Buzzer Harness Side Connector Circuit
Disconnect the warning buzzer connector and check
continuity and voltage between the warning buzzer harness
side connector terminals.

Terminal
NO. Wire
color Connecting to Check itemConnecting
terminal Check condition Standard
3 G/R Tail relay 3-Ground Lighting SW “ON” Approx. 12V
6 Y Fuse CB-5 Voltage
6-Ground Starter SW “ON” Approx. 12V

Door SW Open Continuity
(FRT-LH)
Continuity Close No continuity
2 B Ground 2-Ground - Continuity
FRT door-LH 1-Ground 1
B/W

8A-202 ELECTRICAL-BODY AND CHASSIS
TROUBLESHOOTING
WINDSHIELD WIPER
1. Wiper dose not operate at any switch position

Checkpoint Trouble Cause Countermeasure


Reinstall or replace the fuse
No. RHD: C-9 (20A)

Poor fuse contact or blown
NG

Repair open circuit or
connector contact

1. Wiper motor function when
connecting the motor
connector 3
C-4 to the
battery (+) terminal, and 1
C-4 to the (-) terminal
(Should the wiper motor
rotate at a low speed)
2. Wiper motor function when
connecting the motor
connector 2
C-4 to the
battery (+) terminal, 1
C-4
to the (-) terminal (Should
the wiper motor rotate at a
high speed)
Voltage between 3 B-59 and
the ground (Should be battery
voltage present)

Open circuit or poor connector
contact


Replace the wiper & washer
SW.

Continuity in the wiper &
washer SW.

SW. malfunction
NG NG OK
OK

RHD:
Fuse No. C-9 (20A)


Repair grounding point
C-2
contact


Grounding point
C-2


Poor grounding point contact
NG
OK OK

Replace the wiper motor

Wiper motor malfunction
NG

Repair open circuit or
connector contact

Continuity between 1
C-4
and
C-36


Open circuit or poor connector
contact
NG OK

ELECTRICAL-BODY AND CHASSIS 8A-205
6. Auto-stop function of the wiper motor does not operate

Checkpoint Trouble Cause Countermeasure


Repair open circuit or
connector contact

Open circuit or poor connector
contact
NG

Repair open circuit or
connector contact

Open circuit or poor connector
contact
NG Continuity between the
intermittent relay harness side
connector 6
C-3 and the
wiper motor harness side
connector 6
C-4

Replace the intermittent relay

Relay malfunction
NG
Intermittent relay function

Wiper motor function
1. Disconnect the wiper motor
connector
2. Connect the motor
connector 5
B-59 to the
battery (+) terminal and 1
C-4 to the (-) terminal,
and then change the
connection of the battery (+)
terminal to the connector 4
C-4 while the motor
rotating at a low speed
3. Check to see if the wiper
motor stops at the auto stop
position when connecting
the connector terminals 3
C-4 and 1 C-4 in this
condition
Continuity between the wiper
& washer SW. connector
terminals 5
B-59 and 6 B-59
at the “OFF” position
OK

Replace the wiper motor

Wiper motor malfunction
NG
Repair an open circuit or a
poor connection of the
connectors between the fuse
No. RHD: C-9 (20A) and 4

C-4
Voltage between the wiper
motor harness side connector
terminal 4
C-4 and the
ground (Should be battery
voltage present)

Open circuit or poor connector
contact
NG
OK OK
OK

8A-206 ELECTRICAL-BODY AND CHASSIS
WASHER
1. Washer motor does not operate

Checkpoint Trouble Cause Countermeasure


Reinstall or replace the fuse
No. RHD: C-9 (20A)

Poor fuse contact or blown
NG
Repair or an open circuit or a
poor connection of the
connectors between 2
C-17
and 1
B-59

Open circuit or poor connector
contact
NG Voltage between the washer
motor harness side connector
terminal 2
C-17 and the
ground when the washer
button is depressed (Should
be battery voltage present)

Repair grounding point
C-36
contact


Poor grounding point contact
NG
Grounding point
C-36


Replace the washer motor

Motor malfunction
NG
Washer motor function when
connecting the motor side
connector 2
C-17 to the
battery (+) terminal, and the
connector 1
C-17 to the (-)
terminal (Should the washer
motor rotate) OK

Repair open circuit or
connector contact

Open circuit or poor connector
contact
NG
Continuity between 1
C-17
and
C-36
OK
Continuity between the wiper
& washer SW. side connector
terminals 1
B-59 and 7 B-59
when the washer button is
depressed

RHD:
Fuse No. C-9 (20A)

OK

Replace the wiper & washer
SW.

SW. malfunction
NG
Repair or an open circuit or a
poor connection of the
connectors between the fuse
No. RHD: C-9 (20A) and 7

B-59
Voltage between the wiper &
washer SW. harness side
connector terminal 7
B-59
and the ground (Should be
battery voltage preset)

Open circuit or poor connector
contact
NG
OK OK OK

8A-212 ELECTRICAL-BODY AND CHASSIS
Windshield Washer Spray
Be sure that the engine hood is completely closed before
checking the windshield washer spray adjustment.
Windshield Washer Spray Position: Refer to the illustration.

RTW38DSF000201



Connector
Be absolutely sure that the wiper motor connector is securely
connected.
This will prevent a poor contact and an open circuit.


Note:
Windshield wiper arm and blade assembly configurations
are different for the right-hand and left-hand side of the
vehicle.
Be careful not to confuse the right-hand and left-hand side
assemblies.



This illustration is based on RHD model
WASHER TANK MOTOR
Removal
1. Remove the head light.

Refer to the head light in this manual.
2. Remove the inner riner.
3. Pull out the clip washer filler.
4. Remove the washer tank nuts.

ELECTRICAL-BODY AND CHASSIS 8A-255
TROUBLESHOOTING
SPEEDOMETER
1. Speedometer and odometer do not function

Checkpoint Trouble Cause Countermeasure


Replace the vehicle speed
sensor

Vehicle speed sensor
malfunction
NG
Repair an open circuit in the
circuit or a poor connection at
the connectors
Continuity between the vehicle
speed sensor and the meter,
or the fuse RHD: C-5 (15A)
and the ground

Open circuit or poor connector
contact


Replace the case baseboard
assy

Use a meter tester to check
the speedometer function

Speedometer malfunction
NG NG OK
OK
Check the vehicle speed
sensor output
(4 pulses/1 rotation)




2. Speedometer pointer fluctuates
(May be wide fluctuation)

Replace the vehicle speed
sensor, or repair an open
circuit in the circuit or a
connectors Vehicle speed sensor
malfunction, or open circuit or
poor connector contact
NG

Replace the case baseboard
assy

Use a meter tester to check
the speedometer function

Speedometer malfunction
NG OK
Check the speed sensor
output by using the
oscilloscope