2004 ISUZU TF SERIES clutch

1-44 HEATER AND AIR CONDITIONING

REMOVAL AND INSTALLATION (C24SE)

RTW310MF000401

Removal Steps
1. Magnetic clutch harness connector
2. Compressor belt
3. Refrigerant line
4. Bolt; compressor to bracket
5. Compressor assembly

Installation Steps
5. Compressor assembly

4. Bolt; compressor to bracket

3. Refrigerant line

2. Compressor belt
1. Magnetic clutch harness connector

HEATER AND AIR CONDITIONING 1-53
Important Operation - Resassembly






2. Field Coil
Installation field coil.

Align the located portion (1) of the clutch coil and
compressor.


5. Pulley Asssembly
Using pulley installer and drive handle to install the pulley
assembly.
Pulley Installer: 5-8840-0118-0 (J-33940)
Drive Handle: 5-8840-0007-0 (J-8092)






9. Drive Plate Bolt
Using drive plate holder to prevent the drive plate from
rotating.
Drive Plate Holder: 5-8840-4056-0 (J-37872)
Tighten the bolt to the specified torque.
N
m (kgf
m/Ib
in)

Torque 13 (1.3/113)
After tightening the bolt, check to be sure the pulley rotates
smoothly.

HEATER AND AIR CONDITIONING 1-83

AIR CONDITIONING CYCLE TROUBLESHOOTING

TROUBLE POSSIBLE CAUSE CORRECTION
No cooling or
insufficient
cooling
1. Magnetic clutch does not run


Refer to “MAGNETIC CLUTCH”
troubleshooting in this section
2. Compressor is not rotating properly

Drive belt loosened or broken

Adjust the drive belt to the specified
tension or replace the drive belt


Magnetic clutch face is not clean and
slips
Clean the magnetic clutch face or replace




Incorrect clearance between magnetic
drive plate and pulley

Adjust the clearance (Refer to
“COMPRESSOR OVERHAUL”



Compressor oil leaks from shaft seal or
shell

Replace the compressor




Compressor seized

Replace the compressor

3. Insufficient or excessive charge of
refrigerant

Discharge and recover refrigerant.
Recharge to specified amount.
4. Leaks in the refrigerant system




Check refrigerant system for leaks and
repair as necessary
Discharge and recover refrigerant.
Recharge to specified amount.
5. Condenser clogged or insufficient radiation


Clean the condenser or replace as
necessary


Check radiator or condenser fan function

6. Temperature control link unit of the heater
unit defective

Repair the link unit

7. Unsteady operation due to foreign
substance in expansion valve

Replace the expansion valve

8. Poor operation of electronic thermostat


Check electronic thermostat and replace
as necessary
Insufficient
velocity
of cooling air

1. Evaporator clogged or frosted


Check evaporator core and replace or
clean the core
2. Air leaking from cooling unit or air duct

Check evaporator and duct connection,
then repair as necessary

3. Blower motor does not rotate prop-erly


Refer to “FAN CONTROL KNOB (FAN
SWITCH)” troubleshooting in this section

* For the execution of the charging and discharging operation in the table above, refer to the “RECOVERY,
RECYCLING, EVACUATING AND CHARGING” in this section.

HEATER AND AIR CONDITIONING 1-87

MAGNETIC CLUTCH
When the A/C switch and the fan control knob (fan switch) are turned on with the engine running, current flows
through the thermostat and the compressor relay to activate the magnetic clutch.
The air conditioning can be stopped by turning off the A/C switch or the fan control knob (fan switch).
However, even when the air conditioning is in operation, the electronic thermostat, the pressure switch or the ECM
is used to stop the air conditioning temporarily by turning off the magnetic clutch in the prearranged conditions to
reduce the engine load which is being caused by the rise in the engine coolant temperature, and the acceleration of
the vehicle, etc.

1-90 HEATER AND AIR CONDITIONING

MAGNETIC CLUTCH DOES NOT RUN (4JA1L/4JH1-TC)



Replace
YES


Are the A/C thermo (X-15) and heater & A/C (X-11)
and A/C compressor (X-14) relay OK?

Are the No. SBF-8 fuse (30A) and the No. EB-13
(10A) fuses OK
YES


Is the pressure switch (C-24) OK?
YES


Are the A/C switch (B-57) and the fan switch (B-13)
OK?
NO
YES


Is there continuity between the engine harness
connector terminal No.1 (E-3) and engine room harness
connector terminal No.2 (X-14)?

Disconnect the A/C compressor relay.

Turn the ignition switch "ON" (Engine is running)


A/C switch and fan control knob (fan switch "ON")
NO
Replace
NO
Defective switch or insufficient
refrigerant
NO
NO
Does the magnetic clutch
operate?
YES
Replace


Disconnect the magnetic clutch connector.

Is there battery voltage between the engine room harness
connector terminal No.1 (E-3) and ground?
Defective compressor
YESNO
Defective magnetic clutch

HEATER AND AIR CONDITIONING 1-95

MAGNETIC CLUTCH DOES NOT RUN


Replace
YES

Are the A/C thermo (X-15), heater & A/C (X-11)
and A/C compressor (X-14) relay OK?


Are the No. SBF 8 fuse (30A) and the No. EB-13
(10A) fuses OK
YES

Is the pressure switch (C-24) OK?
YES


Are the A/C switch (B-57) and the fan switch (B-13)
OK?
NO
YES


Is there continuity between the engine harness
connector terminal No.1 (E-2) and engine room
harness connector terminal No.2 (X-14)?


Disconnect the A/C compressor relay.


Turn the ignition switch "ON" (Engine is running)

A/C switch and fan control knob (fan switch "ON")
NO
Replace
NO
Defective switch or insufficient
refrigerant
NO
NO
Does the magnetic clutch
operate?
YES
Replace


Disconnect the magnetic clutch connector.


Is there battery voltage between the engine room
harness connector terminal No.1 (E-2) and ground?
Defective compressor
YESNO
Defective magnetic clutch

1-100 HEATER AND AIR CONDITIONING



Replace
YES


Are the A/C thermo (X-15), heater & A/C (X-11)
and A/C compressor (X-14) relay OK?


Are the No. SBF 8 fuse (30A) and the No. EB-13
(10A) fuses OK?
YES


Is the pressure switch (C-24) OK?
YES


Are the A/C switch (B-57) and the fan switch (B-13)
OK?
NO
YES


Is there continuity between the engine harness
connector terminal No.1 (E-2) and engine room
harness connector terminal No.2 (X-14)?

Disconnect the A/C compressor relay.


Turn the ignition switch "ON" (Engine is running)


A/C switch and fan control knob (fan switch "ON")
NO
Replace
NO
Defective switch or insufficient
refrigerant
NO
NO
Does the magnetic clutch
operate?
YES
Replace


Disconnect the magnetic clutch connector.

Is there battery voltage between the engine room
harness connector terminal No.1 (E-2) and ground?
Defective compressor
YESNO
Defective magnetic clutch

1-104 HEATER AND AIR CONDITIONING

SPECIAL SERVICE TOOL
ITEM NO. ILLUSTRATION PART NO. PART NAME




5-8840-0629-0
(J-39500-A)







5-8840-0630-0
(J-39500-220A)





5-8840-0631-0
(J-39500-220ANZ)


ACL-2

5-8840-4056-0
(J-37872)

Drive plate holder


ACL-4

5-8840-0121-0
(J-33943)

Clutch pulley puller pilot


ACL-5

5-8840-0111-0
(J-8433)

Clutch pulley puller


CDL-10

5-8840-0118-0
(J-33940)

Clutch pulley installer


OTL-1

5-8840-0007-0
(J-8092)

Driver handle