2004 ISUZU TF SERIES reverse

7B1-24 MANUAL TRANSMISSION

Disassembly
1. Remove detent spring plate and gasket (1), detent
spring (2) and detent ball (3).
Use a magnetic hand to remove the detent balls
from the intermediate plate.

220RS011
2. Remove spring (4).
3. Remove rev-5th shift rod (5), and rev-5th shift arm
and reverse inhibitor (6).
Remove 1st-2nd shift rod (7), 3rd-4th shift rod (8),
3rd-4th shift arm (9), and 1st-2nd shift arm (10).


Hold a round bar against the shift rod end.

230RS003


Use a spring pin remover to remove the shift
arm spring pins from the shift arms and the shift
rods.


230RS0004

Be careful not to lose the interlock pins, when
pulling out the shift rod rearward.
Interlock pins are located between the shifter
rods in the intermediate plate.

230RS0005


Remove the rev-5th, 1st-2nd and 3rd-4th shift
rods carefully.
4. Remove interlock pin (11) from intermediate plate
and gear assembly (12).

7B1-26 MANUAL TRANSMISSION

Reassembly
1. Install rev-5th shift arm and reverse inhibitor (6) and
rev-5th shift rod (5).

Apply oil to the reverse inhibitor inner surface.

Install the shift rod in the intermediate plate (12).


Hold a round bar against the shift rod end lower
face to protect it against damage.

Install a new spring pin.
Never reinstall the used spring pin.


Install the interlock pin (11) in the intermediate
plate (12).
Do not allow the interlock pin to fall from the
intermediate plate (12).
2. Install 1st-2nd shift arm (10) and 3rd-4th shift arm(9)
to intermediate plate and gear assembly (12).
3. Install 3rd-4th shift rod (8) and 1st-2nd shift rod (7).


Install the interlock pin (11) in the intermediate
plate and gear assembly (12).


Install the 3rd-4th shift rod (8) in the intermediate
plate (12).
Do not allow the interlock pin to fall from the
intermediate plate.


Install the interlock pin (11) and then 1st-2nd
shift rod (7) in the intermediate plate (12).
Do not allow the interlock pin to fall from the
intermediate plate.


Hold a round bar against the shift rod end lower
face to protect it against damage.

Install a new spring pin.
Never reinstall the used spring pin.

230RS007
4. Install spring (4).
5. Put detent balls (3) in the intermediate plate holes.


Apply oil to the detent balls.
6. Install detent springs (2) and detent spring plate and
gasket (1).


Install a new gasket and the detent spring plate.


Tighten the detent spring plate bolts to the
specified torque.
Torque: 25 N




m (2.5 kg




m/18 lb




ft)


220RS030

Legend
(1) Warped

MANUAL TRANSMISSION 7B1-27

Reverse Gear and 5th Gear
Disassembled View
226R300027

Legend

(1) Bearing Snap Ring (11) Reverse Idler Gear Assembly
(2) Ball Bearing (12) Idle Shaft Pin
(3) Bearing Snap Ring (13) Thrust Washer
(4) Speedometer Drive Gear (14) Reverse Idler Gear
(5) Clip (15) Reverse Idler Shaft
(6) Retainer Snap Ring (16) Bearing Snap Ring
(7) Retainer (17) Ball Bearing
(8) Thrust Plate (18) Counter 5th Gear
(9) Thrust Washer and Lock Ball (19) Counter Reverse Gear
(10) Reverse Idler Gear Snap Ring (20) 5th Gear

7B1-28 MANUAL TRANSMISSION

(21) 5th Block Ring (26) Reverse Gear
(22) Needle Bearing (27) Needle Baring
(23) Mainshaft Nut (28) Bearing Plate and Screw
(24) Rev-5th Synchronizer Assembly (29) Bearing Snap Ring
(25) Reverse Block Ring (30) Intermediate Plate

MANUAL TRANSMISSION 7B1-29

Disassembly
1. Use a pair of snap ring pliers to remove the bearing
snap ring (1).
2. Set the bearing remover 5-8840-2155-0 and puller
5-8840-2027-0 to the bearing (2) and the mainshaft
end to remove the ball bearing (2).
262L100001
3. Remove the bearing snap ring (3), clip (5),
speedometer drive gear (4), retainer snap ring (6)
and retainer (7).
4. Remove thrust plate (8) and thrust washer and lock
ball (9).
5. Use a pair of snap ring pliers to remove reverse idler
gear snap ring (10).

226RS004

6. Remove the reverse idler gear assembly (11) from
the intermediate plate (30).

226RS005
7. Remove idle shaft pin (12), thrust washer (13),
reverse idler gear (14), and reverse idler shaft (15).
8. Use a pair of snap ring pliers to remove the snap
ring (16).
9. Attach a universal puller to the counter gear shaft.
Use a universal puller to remove the ball bearing
(17) and the counter 5th gear (18).

226RS006
10. Remove counter reverse gear (19).

MANUAL TRANSMISSION 7B1-31

13. Use screw drivers between the reverse gear (26)
and bearing plate (28) to remove the Rev-5th
synchronizer assembly (24) together with reverse
block ring (25) and reverse gear (26).

226RS010
14. Remove needle bearing (27).
15. Use the torx bit wrench (T45) 5-8840-0047-0 to
remove the bearing plate and screw(28) from the
intermediate plate.

220RW137
16. Use the snap ring pliers (1) to remove the mainshaft
bearing snap ring (2) (29).


226RS011
17. Hold the snap ring open with the pliers.
Push the intermediate plate (30) toward the rear of
the transmission to remove it.
The bearing snap ring (29) will come free.

Inspection and Repair
Refer to Top Gear Shaft, Main Gear Shaft, and Counter
Gear in this section for inspection and repair.

Reassembly
1. Mesh the counter gear with the mainshaft assembly.
Set the holding fixture 5-8840-2160-0 to the
mainshaft and the counter gear and then install it on
the base 5-8840-0003-0.
Install the intermediate plate (30) on the gear
assembly.
226RW212

7B1-32 MANUAL TRANSMISSION

2. Install bearing snap ring (29).
3. Apply recommended thread locking agents
(LOCTITE 242) or its equivalent to each of the
bearing plate screw threads.
Install bearing plate and screw (28).
Tighten the screws to the specified torque by using
torx bit wrench 5-8840-0047-0.
Torque: 15 N




m (1.5 kg




m/11 lb




ft)

220RW137
4. Install needle bearing (27), reverse gear (26), and
reverse block ring (25). 5. Assemble rev-5th synchronizer assembly (24) by
performing the following steps.
1. Turn the clutch hub face (1) toward the sleeve
groove (2) (rear side) on the outer
circumference.
2. Check that the inserts (3) fit snugly into the
clutch hub (5) ring insert grooves.
3. Check that the inserts springs (4) are fitted to
the inserts as shown in the illustration.
4. Check that the clutch hub (5) and the sleeve (6)
slide smoothly.
5. Install the synchronizer assembly (24) to the
mainshaft.
The clutch hub face with the heavy boss must be
facing the reverse gear side.

226RS013

226RS049

MANUAL TRANSMISSION 7B1-33

6. Mesh the 1st-2nd and 3rd-4th synchronizers with
both the 1st and 3rd gears (double engagement).

226RS015
This will prevent the mainshaft from turning.
7. Install the new mainshaft hub nut.
Use the mainshaft nut wrench 5-8840-2156-0 to
tighten the mainshaft nut (23) to the specified
torque.
Torque: 137 N




m (14 kg




m/101 lb




ft)
226RW214


8. Use a punch to stake the mainshaft nut (23).

226RW153
9. Install needle bearing (22), 5th block ring (21), and
5th gear (20).
10. Apply engine oil to the counter reverse gear (19) and
the reverse gear (26).
Install the counter reverse gear (19) to the counter
shaft.
The reverse gear projection must be facing the
intermediate plate.

226RW151