2004 ISUZU TF SERIES reverse

7B-20 MSG MODEL
REVERSE GEAR AND 5TH GEAR


Disassembly Steps
1. Bearing snap ring
2. Speedometer drive gear and lock ball
3. Bearing spacer
4. Mainshaft end ball bearing
5. Thrust ring snap ring
6. Thrust washer thrust ring
7. Thrust washer and lock ball
8. Counter reverse gear nut and washer


9. Counter end ball bearing


10. Counter 5th gear
11. Counter reverse gear
12. 5th gear
13. 5th block ring
14. Needle bearing



15. Mainshaft lock nut and washer


16. Rev. - 5th synchronizer assembly
17. Reverse gear
18. Needle bearing
19. Needle bearing collar
20. Thrust washer
21. Counter reverse gear lock nut
22. Thrust washer
23. Reverse idler gear
24. Thrust washer
25. Reverse idler shaft


26. Bearing snap ring


27. Bearing snap ring


28. Intermediate plate

MSG MODEL 7B-27




REVERSE IDLER GEAR AND IDLER
GEAR SHAFT CLEARANCE
1. Use a micrometer to measure the idler gear shaft diameter.
2. Use an inside dial indicator to measure the idler gear inside
diameter.
3. Calculate the idler gear and idler gear shaft clearance.
Idler gear inside diameter - idler gear shaft diameter = idle
r
gear and idler gear shaft clearance.
If the measured value exceeds the specified limit, the idle
r
gear and/or the idler gear shaft must be replaced.
Idler Gear and Idler Gear Shaft Clearance mm(in)
Standard Limit
0.041 - 0.074 (0.0016 - 0.0029) 0.150 (0.0059)





CLUTCH HUB SPLINE PLAY
1. Set a dial indicator to the clutch hub to be measured.
2. Move the clutch hub as far as possible to both the right and
the left.
Note the dial indicator reading.
It the measured value exceeds the specified limit, the
clutch hub must be replaced.
Clutch Hub Spline Play mm(in
)
Standard Limit
0.019 (0 - 0.075) 0.20 (0.0079)

7B-34 MSG MODEL
REVERSE GEAR AND 5TH GEAR



Reassembly Steps


1. Intermediate plate


2. Reverse idler shaft
3. Bearing snap ring
4. Bearing snap ring
5. Thrust washer


6. Reverse idler gear
7. Thrust washer


8. Counter reverse gear lock nut


9. Thrust washer
10. Needle bearing collar
11. Needle bearing
12. Reverse gear


13. Rev.-5th synchronizer assembly


14. Mainshaft lock nut and washer

15. Needle bearing
16. 5th block ring
17. 5th gear


18. Thrust washer and lock ball
19. Counter reverse gear
20. Counter 5th gear
21. Counter end ball bearing


22. Counter reverse gear nut and washer


23. Thrust washer thrust ring


24. Thrust ring snap ring
25. Mainshaft end ball bearing
26. Bearing spacer
27. Speedometer drive gear and lock ball
28. Bearing snap ring

MSG MODEL 7B-35


Important Operations
1. Intermediate Plate
2. Reverse Idler Shaft
1) Install the reverse idler shaft to the intermediate plate.
2) Tighten the reverse idler shaft bolt to the specified torque.
Idler Shaft Bolt Torque Nm(kgfm/lbft)
18.6 (1.9 / 13.7)



3) Set the mainshaft with gear assembly

1 and the counter
gear assembly

2 to the holding fixture
3.
Holding Fixture : 5-8840-2001-0 (J-29768)
4) Place the holding fixture (with the mainshaft and the
counter shaft) in a vise.
5) Mesh the 3rd-4th synchronizer to the 3rd gear.
Mesh the 1st-2nd synchronizer to the 1st gear.
6) Install the intermediate plate to the mainshaft and the
counter gear ball bearings.



6. Reverse Idler Gear
8. Counter Reverse Gear Lock Nut
1) Apply the engine oil to the idler shaft and the reverse gear
inside circumference.
2) Install the reverse gear to the idler shaft.
3) Install a new counter reverse gear lock nut.
Never reinstall the old lock nut.
4) Tighten the reverse gear lock nut to the specified torque.
Lock Nut Torque Nm (kgfm/lbft)
107.8 (11 / 79.6)



9. Thrust Washer
1) Apply the engine oil to both sides of the thrust washer.
2) Install the thrust washer to the mainshaft.
The thrust washer oil groove must be facing the reverse
gear side.

7B-36 MSG MODEL


13. Rev.-5th Synchronizer Assembly
1) Apply the engine oil to the clutch hub spline.
2) Install the synchronizer assembly to the mainshaft.
The sleeve heavy chamfer

1 and the insert short side
2
must be facing to the rear side of the transmission.


14. Mainshaft Lock Nut and Washer
1) Install a new lock nut and washer to the mainshaft.
Never reinstall the used lock nut and washer.
2) Use the lock nut wrench to tighten the lock nut to the
specified torque.
Lock Nut Wrench : 5-8840-0353-0 (J-36629)
Lock Nut Torque Nm(kgfm/lbft)
107.8 (11 / 79.6)



22. Counter Reverse Gear Nut and Washer
Tighten the counter gear lock nut to the specified torque.
Reverse Gear Nut Torque N
m(kgf
m/lb
ft)
107.8 (11 / 79.6)



18. Thrust Washer and Lock Ball
23. Thrust Washer Thrust Ring
24. Thrust Ring Snap ring
1) Install the thrust washer with lock ball together with the
thrust ring to the mainshaft.
2) Use a pair of snap ring pliers to install the snap ring.


3) Use a thickness gauge to measure the clearance between
the 5th gear and the thrust washer.
5th Gear and Thrust Washer Clearance mm(in)
Standard
0.1 - 0.3 (0.004 - 0.012)
If required, replace the existing thrust washer with a new
thrust washer to bring the clearance to specification.

MANUAL TRANSMISSION 7B1-1

SECTION 7B1
TRANSMISSION
MANUAL TRANSMISSION MUA
CONTENTS
PAGE
MUA (4





2)
Service Precaution .......................................................................................................... 7B1 – 3
General Description ........................................................................................................ 7B1 – 4
Rear Oil Seal (4




2) ........................................................................................................... 7B1 – 5
Transmission (4




2) ......................................................................................................... 7B1 – 7
Disassembled View ..................................................................................................... 7B1 – 7
Removal ....................................................................................................................... 7B1 – 8
Installation ................................................................................................................... 7B1 –12
Transmission Case .......................................................................................................... 7B1 –18
Major Component ........................................................................................................ 7B1 –18
Disassembly ................................................................................................................ 7B1 –19
Reassembly ................................................................................................................. 7B1 –20
Intermediate Plate with Gear Assembly, Detent, Shift Arm, Shift Rod,
and Interlock Pin ........................................................................................................... 7B1 –23
Disassembled View ..................................................................................................... 7B1 –23
Disassembly ................................................................................................................ 7B1 –24
Inspection and Repair ................................................................................................. 7B1 –25
Reassembly ................................................................................................................. 7B1 –26
Reverse Gear and 5th Gear ............................................................................................ 7B1 –27
Disassembled View ..................................................................................................... 7B1 –27
Disassembly ................................................................................................................ 7B1 –29
Inspection and Repair ................................................................................................. 7B1 –31
Reassembly ................................................................................................................. 7B1 –31
Top Gear Shaft, Main Gear Shaft, and Counter Gear Shaft ......................................... 7B1 –38
Disassembled View ..................................................................................................... 7B1 –38
Disassembly ................................................................................................................ 7B1 –40
Inspection and Repair ................................................................................................. 7B1 –42
Reassembly ................................................................................................................. 7B1 –45
Main Data and Specifications ......................................................................................... 7B1 –51

7B1-2 MANUAL TRANSMISSION

Troubleshooting ............................................................................................................... 7B1 –55
Special Tools (4





2) .......................................................................................................... 7B1 –62


MUA (4





4)
Service Precaution .......................................................................................................... 7B1 –63
General Description ........................................................................................................ 7B1 –64
Transmission (4




4) ......................................................................................................... 7B1 –65
Disassembled View ..................................................................................................... 7B1 –65
Removal ....................................................................................................................... 7B1 –66
Installation ................................................................................................................... 7B1 –70
Transmission Case .......................................................................................................... 7B1 –77
Major Component ........................................................................................................ 7B1 –77
Disassembly ................................................................................................................ 7B1 –78
Reassembly ................................................................................................................. 7B1 –79
Intermediate Plate with Gear Assembly, Detent, Shift Arm, Shift Rod,
and Interlock Pin ........................................................................................................... 7B1 –82
Disassembled View ..................................................................................................... 7B1 –82
Disassembly ................................................................................................................ 7B1 –83
Inspection and Repair ................................................................................................. 7B1 –83
Reassembly ................................................................................................................. 7B1 –84
Reverse Gear and 5th Gear ............................................................................................ 7B1 –85
Disassembled View ..................................................................................................... 7B1 –85
Disassembly ................................................................................................................ 7B1 –86
Inspection and Repair ................................................................................................. 7B1 –88
Reassembly ................................................................................................................. 7B1 –88
Top Gear Shaft, Main Gear Shaft, and Counter Gear Shaft ......................................... 7B1 –94
Disassembled View ..................................................................................................... 7B1 –94
Disassembly ................................................................................................................ 7B1 –96
Inspection and Repair .............................................................................................. 7B1 – 98
Reassembly .............................................................................................................. 7B1 – 101
Main Data and Specifications ..................................................................................... 7B1 – 107
Troubleshooting ........................................................................................................... 7B1 – 111
Special Tools (4





4) ...................................................................................................... 7B1 – 118

MANUAL TRANSMISSION 7B1-23

Intermediate Plate with Gear Assembly, Detent, Shift Arm, Shift Rod, and
Interlock Pin
Disassembled View



RTW47BLF000501
Legend

(1) Detent Spring Plate and Gasket (7) 1st-2nd Shift Rod
(2) Detent Spring (8) 3rd-4th Shift Rod
(3) Detent Ball (9) 3rd-4th Shift Arm
(4) Spring (10) 1st-2nd Shift Arm
(5) Rev-5th Shift Rod (11) Interlock Pin
(6) Rev-5th Shift Arm and Reverse Inhibitor (12) Intermediate Plate and Gear Assembly