2004 DACIA SOLENZA battery replacement

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 12
Procedures
A. E.C.U. DECODER REPLACEMENT PROCEDURE AND
ANTI STARTING CODE MEMORISING
The new E.C.U. decoder is always not coded. After its mounting on the vehicle it is necessary
that this one is memorising the anti starting code in order to be operational.
REMARK:
If only the E.C.U. decoder i s replaced, there i s no need of an i ntervention to t he
E.C.U. injection (injection computer), which will keep the old anti starting code.
AT T E N T I ON!
After the E.C.U. de coder memorised the anti starting c ode, this code cannot be erased
or replaced with another one. In order t o perform this procedure, one of the keys of t he ve hicle and the CLIP tester are
needed.
Proceed as follows:
1. Connect the CLIP tester to the diagnostic socket and to the battery (or the lighter socket)
of the vehicle. 2. Read the configuration of the old E.C.U. decoder in the following way, before dismounting
it from the vehicle:
- select the type “B41”
- enter the menu “ COMPUTER TEST” then select “ ANTI STARTING”
- access “COMMAND MODE” then “CONFIGURATIONS READING”
- note the configurations found : petrol, programming with 1 or 2 keys, ceiling delayed
light, the type of the doors’ blocking switch (CPE), etc.;
3. Return to the menu “COMPUTER TEST”
4. Remove the old E .C.U. decoder and replace it with a new one, the contact being off.
5. Enter the menu “ANTI STARTING”, then select “ STATE LIST”. If the E.C.U. decoder is
new, you must find the following states:
18G FIRST CYCLE MEMORISING………………….......………… PASSIVE
19G NOT PERFORMED KEY PROGRAMMING ………..……….. ACTIVE
19D UNBLOCKED KEY PROGRAMMING ……………….………ACTIVE
OBSERVAT ION:
If the states 19G and 19D are not “ACTIVE” this means the E.C.U. decoder has
b een already used, so it isn’t new and cannot memorise another anti starting code.
6. Access t he menu “COMMAND MODE” and then “CONFIGURATION”, where you
will c onfigure t he new E .C.U. decoder in the same way as the old one : petrol, 1 ke y, ceiling
delayed light, impulsion doors blocking switch, etc. selecting one by one these configurations,
which you’ll validate with “CLICK” on the blue button on right top of the screen.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 14
Procedures
RE M ARK:
For the RF remote control synchronisation, after the replacement of an E.C.U. decoder,
the sync hron is ation proced ure must be per formed taking i nto account the foll owing
situations : - fo r one RF remote control, perform the “ SIMPLE SYNCHRONISED
PROCED URE ”;
- for the second RF remote co ntrol per form the “SPE CI FI C SYNCHRONI SED
PROCED URE ”.
B. KIT REPLACEMENT PROCEDURE
(E.C.U. decoder plus 2 key he ads)
In case of one kit replacement perform the following steps:
- memorising the anti starting code by the E.C.U. decoder;
- memorising of the new anti starting code by the injection computer; it is necessary the
repairing code (found out based on the old ke y heads code) and t he CLIP tester.
Perform the actions in the following sequence:
1. Mount the metal insertions of the old keys to the new key heads.
2. Inform by phone at ”Client Voice” (phone no 0248 500 000), the vehicle chassis series and
the key heads code, written on the vehicle invoice, in order to get the repairing code.
3. Connect the CLIP tester t o the diagnostic socket and to the battery (or to the lighter
s ocket) of the vehicle. Read the configuration of the old E.C.U. decoder before dismounting it
off the vehicle, as follows:
- select vehicle type “B41”;
- enter the menu “ COMPUTER TEST” then select “ ANTI STARTING”;
- access “COMMAND MODE” then “READ CONFIGURATIONS”;
- note the configuration s : petrol/diesel, programming with 1 or 2 keys, ceiling delayed light,
the type of the doors’ blocking switch (CPE), etc.
4. Return to the menu “ANTI START ING”.
5. Dismount the old E.C.U. decoder and replace it with a new one, the contact being off.
6. Check the configuration of the new E.C.U. decoder selecting “ STAT E LIST”; here you
must find the following states: 18G FIRST KEY MEMORISING……………………………........… PASSIVE
19G NOT PERFORMED KEY PROGRAMMING ………………..... ACTIVE
19D UNBLOCKED KEY PROGRAMMING ……………………..... ACTIVE
REMARK:
If the state 19G and 19D are not “ACTIVE” this means the E.C.U. decoder isn’t a
ne w one and cannot memorise another anti starting code.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 16
Procedures
17. The procedure is finished. Check the engine starting with both keys.
REMARK:
For the RF remote control synchronisation, after the replacement of a kit, take into account
the following situations:
- for the first RF remote control, perform the “ SIMPLE SYNCHRONISED PROCEDURE”;
- for t he second RF re m ote control pe rform the “SPE CIFIC SYNCHRONISE D
PROCEDURE”. C. CODE REPAIRING INTRODUCTION PROCEDURE
The repairing code may be introduced only by means of the CLIP tester. This is possible only
if when setting the contact on, the anti starting indicator blinks rapidly, this being confirmed by the
state:
10G ANTI STARTING ……………………………………………….ACTIVE
After getting from DACIA database the repairing code (based on the vehicle chassis series
and on the code from the vehicle’s key head), perform the following operations.
1. Connect the CLIP tester to the diagnostic socket and to the battery (or to the lighter
socket) of the vehicle.
2. The anti start up indicator must blink slowly , the contact being taken off.
3. Set the contact in “M” position. The indicator must blink rapidly.
4. Select vehicle type “B41”;
5. Select the menu “ COMPUTER TEST” then select “ ANTI STARTING”.
6. In the menu “STAT E LIST” find the state 10G “ANTI STARTING” which must be
“ACTIVE”. 7. Access “COMMAND MODE” then select “ACTUATORS”.
8. Select the command “ MANUAL CODE INTRODUCTION” where you will write the
repairi ng c ode (form ed of 4 fi gures), then validate it with t he ke y “ ENTER”. The message
“COMMAND IN PROGRESS” will be displayed followed by the message “FINISHED
COMMAND”. 9. Now the procedure is finished and you may start the vehicle engine.
AT T E N T I ON!
Yo u may perform three attempts of introducing the repairing code; if after the third
essay the code is not yet valid, wait for 15 minutes, take off the contact and then set it
again, then other three attempts may be performed.
REMARK:
This procedure does not decode the injection computer, but is only allowing the start
of the vehicle’s engine. After 10 minutes have passed from the first introduction of the
r epairing code or after the disconnection of the battery, the vehicle’s engine cannot be
s tarted unless a new repairing code is introduced.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 17
Procedures
D. SIMPLE SYNCHRONISED PROCEDURE
This procedure allows the synchronisation of a RF remote control with E.C.U. decoder and
is to be applied in the following situations: -the RF remote control c ode is no longer in the range of the E .C.U. decoder reception,
because of blind consecutive pushing over a 1000 time on the RF remote control button.;
- the replacement of the E .C.U. decoder with a new one;
- the replacement of the RF remote control if the E.C.U. decoder is new (E.C.U. decoder
replacement plus a RF key.);
The following operations will be performed: -take off the contact;
- push and maintain like that for about 5 seconds, the doors locking switch located on the
dashboard ; the doors actuators are performing a closing/opening course;
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system indicator, push twice the RF remote control button; the doors actuators are performing a
closing/opening course;
-the procedure of synchronisation is finished; check the doors blocking/ unlocking by
pushing the RF remote control.
OBSERVAT ION:
During those 10 seconds you can visualise by means of the CLIP tester t he state 17G
“PROGRAMMING OR TIR/TRF RESYNCHRONISATION” which must be ACTIVE.
E. SPECIFIC SYNCHRONISED PROCEDURE
This procedure is used for the synchronisation of the second RF key with E.C.U. decoder
and will be performed as follows:
-connect the CLIP tester to the diagnostic socket and the battery (or the lighter socket)
of the vehicle;
- select the vehicle type “B41”;
- select the menu “ COMPUTERS TEST” then “ ANTI STARTING”;
- enter the menu “COMMAND MODE” and select “CONFIGURATION”;
- validate the command “ PROGRAMMI NG THE SECOND TIR / TRF KEY” launching
the command from the blue button situated on the right top of the screen; the doors actuators are
performing a closing/opening course. - during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system, push twice t he RF remote control button; the doors will block and then unlock and the
anti starting indicator will turn off. The second remote control is now synchronised. Check the
blocking/ unlocking by pushing the RF remote control.
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 3
REPLACEMENT OF COCKPIT INTERMEDIARY RELAY
DISMOUNTING
Disconnect the battery (-) terminal.
Dismount the relays assembly and UCE decoder.
Remove the relay: flash (6), timer (7 ), signaling (8) or speed limit warning ( 9) from their
connectors. Mark the identification of the relays mounting position.
REMOU NT I NG
Reconnect the relays observing the mounting position prior to dismountin g.
Remount the assembly relays and UCE decoder.
Reconnect the battery (-) terminal.
Pe rform functional tests, noticing the correct operation of all consumers supplied by means of the
cockpit relays asse mbly and UCE decoder.
OBSERVATION :
A fter battery reconnecting, re- program the clock, and for vehicles equipped with
p rogrammable radio tape player, re-introduce the radio code.
Relays and UCE decoder assembly from cockpit
vnx.su

88
WIRING
88 - 4
it is not c orrect, see c hapter “
Diagnostic”.
AIRBAG SYSTEM CONFIGURATION
Because the vehicle is e quipped only the
driver’s airbag, it i s necessary the UCE airbag
configuration only “with driver’s airbag”.
In case UCE airbag configuration does not
match with the vehicle equipping, the airbag
indicator will remain lighted.
-S elect menu “ Diagnostic”
- Select and validate vehicle type.
-S elect and validate diagnostic system
“Airbag/ Pre-tensioning systems” - Select mode “ Control”.
-S elect function “ Programmi ng” then
configure the computer only “ With driver’s
airbag ”.
-S et the contact off then reset t he contact
on for in order to validate the configuration.
In the case of the UCE airbag configuration, the
airbag indicator from the instrument panel is
remaining lighted because new UCE airbag are
delivered in blocked state. -S elect mode “ Control”, select mode “
Configuratio ns reading” or select m enu
“States list” and e nsure that modification ha s
been taken into consideration.
AT T E N T I ON!
N on-observing of these prescriptions may
ge ne rat e an abnorm a l ope rat i on of t he
sy stem, even undesirable releasing of the
airbag. UCE airbag may accept up to maximum
4 ai rbag re leasing (c ert ai n e lements are
loosing their nominal characteristics). It is
n ot necessary the systematic replacement
after each airbag releasing.
UCE AIRBAG UNBLOCKING
Af ter replacing UCE airbag it is necessary
the re leasing lines unblocking. The same
method as for the UCE airbag blocking is to
be used, by validation c ontrol “ Computer
unblocking”. The airbag indicator from the
instrument panel is getting off.
REMARK:
The 30 pins connecto r of the UCE
airbag has a shunt circuit that is short-
circuiting the different transmitting
lines of the releasing signal when this
one is disconnected, avoiding the
undesirable releasing of this system (by
antenna effect, for instance)
REMARK:
UCE airbag supply and the
pyrotechnic gas generator is performed
by means of the vehicle bat tery. UCE
airbag is disposing of a reserve electric
energy enabling nevertheless the airbag
r eleasing even if, at the be ginning of a
shock, the v ehicle battery i s not anymore
supplying the UCE airbag.
Airbag – Electronic control unit
vnx.su

88
WIRING
88 - 23
Diagnostic – Failure locating tree
Ensure t hat not CL IP tester i s the failure cause – try its communication with some ot her
vehicle UCE airbag. If CLIP tester is not the failure cause and the dialogue is not established
with no other computer of the same vehicle, it is possible that another damaged computer is
perturbing the diagnostic lines L and K.
Proceed by consecutive disconnection for damaged computer locating.
Check the battery voltage and perform the necessary interve ntions in order to obtain an
adequate vol tage, with the value between 10.5 volts and 15 volts.
Check the presence and condition of the supply fuse of UCE airbag.
Check the correct connection of the computer connector and the cables condition.
Check the computer correct supplying: -Disconnect UCE airbag then connect the 30 pins adapter B40.
- Check and ensure voltage presence be tween plugs marked mass and +DC (+ after
contact)
Check the correct supplying of the diagnostic socket: -supply + permanent at pin 16
- mass at pin 5
Check the continuity and insulation of the connection lines diagnostic socket / UCE airbag:
- plug 23 of UCE airba g pin 15 diagnostic socket (line L)
- plug 9 of UCE a irbag pin 7 di agnostic socket (line K)
If dialogue is not established after these checking, replace UCE airbag (see c hapter “UCE
airbag replacement) .
Missing dialog with the airbag computer.
ALP1
RECOMMENDATIONSCharacteristics : nothing to notice
AFTER
INTERVENTION After communication establishing, treat the possible declared failures.
vnx.su