2003 NISSAN TEANA light

LT-208
PARKING, LICENSE PLATE AND TAIL LAMPS

Parking, License Plate and Tail Lamps Do Not IlluminateBKS001QV
1. PERFORM IPDM E/R ACTIVE TEST
With CONSULT-II
1. Select “IPDM E/R” on CONSULT-II, and select “ACTIVE TEST” on “SELECT DIAG MODE” screen.
2. Select “TAIL LAMP” on “SELECT TEST ITEM” screen.
3. Touch “ON” screen.
4. Check parking, license plate and tail lamps operation.
Without CONSULT-II
1. Start auto active test. Refer to PG-21, "
Auto Active Test" .
2. Check parking, license plate and tail lamps operation.
OK or NG
OK >> GO TO 2.
NG >> GO TO 4.
2. PERFORM BCM SELF-DIAGNOSIS
Select “BCM” on CONSULT-II, and perform self-diagnosis for
“BCM”.
Displayed self
-diagnosis results
NO DTC>>GO TO 3.
CAN COMM CIRCUIT>>Refer to LAN-49, "
CAN System Specifica-
tion Chart" .
3. CHECK CIRCUIT BETWEEN COMBINATION SWITCH AND BCM
With CONSULT-II
1. Select “BCM” on CONSULT-II, and select “HEAD LAMP” on “SELECT TEST ITEM” screen.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “LIGHT SW 1ST” turns ON-OFF according to
lighting switch operation.
Without CONSULT-II
Refer to LT- 1 8 5 , "
Combination Switch Inspection" .
OK or NG
OK >> Replace BCM. Refer to BCS-16, "Removal and Installa-
tion of BCM" .
NG >> Check combination switch (lighting switch). Refer to LT- 1 8 5 , "
Combination Switch Inspection" . Parking, license plate and tail lamps should operate.
Parking, license plate and tail lamps should operate.
SKIA5957E
PKIA7627E
When lighting switch is the
1ST position: LIGHT SW 1ST ON
PKIA7607E

LT-212
PARKING, LICENSE PLATE AND TAIL LAMPS

Tail lamp Indicator Does Not IlluminateBKS002FU
1. CHECK UNIFIED METER AND A/C AMP.
1. Select “METER A/C AMP” on CONSULT-II, and perform self-diagnosis for “METER A/C AMP”.
2. Check if malfunction is indicated.
Is malfunction indicated?
YES >> Repair or Replace malfunctioning parts.
NO >> GO TO 2.
2. CHECK COMBINATION METER INPUT SIGNAL
1. Select “METER A/C AMP” on CONSULT-II.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “LIGHT IND” turns ON-OFF according to lighting
switch operation.
OK or NG
OK >> Replace combination meter. Refer to DI-25, "Disassem-
bly and Assembly of Combination Meter" .
NG >> Replace unified meter and A/C amp. Refer to DI-34,
"Removal and Installation of Unified Meter and A/C
Amp." .
PKIA6866E
When lighting switch is in
the 1ST position : LIGHT IND ON
PKID0111E

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-213
C
D
E
F
G
H
I
J
L
MA
B
LT

Parking, License Plate and Tail Lamps Do Not Go OFFBKS002FT
1. CHECK IPDM E/R FUNCTION
Make sure that lighting switch is OFF. And then check if ignition switch is ON or OFF when parking, license
plate, and tail lamps go OFF.
Check results
Lamps go OFF when ignition switch is ON>>Replace IPDM E/R. Refer to PG-28, "Removal and Installation
of IPDM E/R" .
Lamps go OFF when ignition switch is OFF>>GO TO 2.
Lamps do not go OFF when ignition switch is ON and OFF.>>GO TO 4.
2. CHECK BCM INPUT SIGNAL
1. Select “BCM” on CONSULT-II, and select “HEAD LAMP” on “SELECT TEST ITEM” screen.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “IGN ON SW” turns ON-OFF according to igni-
tion switch operation.
OK or NG
OK >> Replace BCM, refer to BCS-16, "Removal and Installa-
tion of BCM" or IPDM E/R, refer to PG-28, "Removal
and Installation of IPDM E/R" .
NG >> GO TO 3.
3. CHECK BCM POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check voltage between BCM harness connector and ground.
OK or NG
OK >> Replace BCM. Refer to BCS-16, "Removal and Installation of BCM" .
NG >> Repair harness or connector.When ignition switch is in
the ON position: IGN ON SW ON
When ignition switch is in
the OFF or ACC position: IGN ON SW OFF
PKID0285E
Terminal Ignition switch position
(+)
(−)OFFACCON
BCM
connectorTerminal
M3 38 Ground Approx. 0 V Approx. 0 VBattery
voltage
PKID0110E

LT-214
PARKING, LICENSE PLATE AND TAIL LAMPS

4. PERFORM IPDM E/R ACTIVE TEST
With CONSULT-II
1. Select “IPDM E/R” on CONSULT-II, and select “ACTIVE TEST” on “SELECT DIAG MODE” screen.
2. Select “TAIL LAMP” on “SELECT TEST ITEM” screen.
Without CONSULT-II
1. Start auto active test. Refer to PG-21, "
Auto Active Test" .
Do parking, license plate and tail lamps turn OFF?
YES >> GO TO 5.
NO >> Replace IPDM E/R. Refer toPG-28, "
Removal and
Installation of IPDM E/R" .
5. CHECK CIRCUIT BETWEEN COMBINATION SWITCH AND BCM
With CONSULT-II
1. Select “BCM” on CONSULT-II, and select “HEAD LAMP” on “SELECT TEST ITEM” screen.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “LIGHT SW 1ST” turns ON-OFF according to
lighting switch operation.
Without CONSULT-II
Refer to LT- 1 8 5 , "
Combination Switch Inspection" .
OK or NG
OK >> Replace BCM. Refer to BCS-16, "Removal and Installa-
tion of BCM" .
NG >> Check combination switch (lighting switch). Refer to LT- 1 8 5 , "
Combination Switch Inspection" .
SKIA5957E
When lighting switch is in
the OFF position: LIGHT SW 1ST OFF
PKID0302E

LT-244
ILLUMINATION

ILLUMINATIONPFP:27545
System DescriptionBKS001RI

BCM (Body Control Module) controls illumination lamp operation.

IPDM E/R (Intelligent Power Distribution Module Engine Room) operates illumination lamps according to
CAN communication signals from BCM.
OUTLINE
Power is supplied at all times

to ignition relay (located in IPDM E/R), from battery direct,

through 50A fusible link (letter M, located in fuse and fusible link box)

to BCM terminal 55,

through 15A fuse [No. 17, located in fuse block (J/B)]

to BCM terminal 42 and

to combination meter terminal 7,

through 15A fuse (No. 71, located in IPDM E/R)

to tail lamp relay (located in IPDM E/R) and

to CPU (central processing unit) in IPDM E/R

through 15A fuse (No. 78, located in IPDM E/R)

to CPU in IPDM E/R,

through 10A fuse [No. 19, located in fuse block (J/B)]

to unified meter and A/C amp. terminal 21.
With the ignition switch in the ON or START position, power is supplied

to ignition relay (located in IPDM E/R),

through 10A fuse [No. 1, located in fuse block (J/B)]

to BCM terminal 38,

through 10A fuse [No. 12, located in fuse block (J/B)]

to unified meter and A/C amp. terminal 22,

through 10A fuse [No. 14, located in fuse block (J/B)]

to combination meter terminal 8.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM terminal 11.
Ground is supplied

to BCM terminal 52

to unified meter and A/C amp. terminals 29 and 30, and

to combination meter terminals 10, 11, and 12

through grounds M71 and M72,

to IPDM E/R terminals 38 and 60

through grounds E1 and E31.
ILLUMINATION OPERATION BY LIGHTING SWITCH
When the lighting switch is in 1ST position, BCM detects the LIGHTING SWITCH 1ST POSITION (ON) by
BCM combination switch reading function. And then, BCM sends position light request signal (ON) through
CAN communication and MR output signal.
When receiving position light request signal (ON), IPDM E/R turns ON tail lamp relay in IPDM E/R. And then
supplies power

through IPDM E/R terminal 22

to glove box lamp terminal 1

to A/T device illumination terminal 1 (with A/T)

to CVT device illumination terminal 1 (with CVT)

to rear sunshade front switch (illumination) terminal 5 (with rear sunshade)

ILLUMINATION
LT-245
C
D
E
F
G
H
I
J
L
MA
B
LT


to VDC off switch (illumination) terminal 3 (with VDC)

to CD auto changer (illumination) terminal 14 (with CD auto changer)

to audio unit (illumination) terminal 8

to door mirror remote control switch (illumination) terminal 16

to hazard switch (illumination) terminal 3

to headlamp washer switch (illumination) terminal 3

to cigarette lighter socket terminal 2

to headlamp aiming switch (illumination) terminal 3 (without xenon headlamp)

to A/C and AV switch (illumination) terminal 16

to front heated seat switch (driver side) (illumination) terminal 5

to front heated seat switch (passenger side) (illumination) terminal 5

to front air massage seat switch (illumination) terminal 5 (with air massage seat)

to front door armrest illumination (driver side) terminal 1

to front door armrest illumination (passenger side) terminal 1

to rear door armrest illumination LH terminal 1

to rear door armrest illumination RH terminal 1

to rear sunshade rear switch (illumination) terminal 8 (with rear center armrest switches)

to rear audio control switch (illumination) terminal 17 (with rear center armrest switches)

to rear heated seat switch LH (illumination) terminal 25 (with rear heated seat) and

to rear heated seat switch RH (illumination) terminal 33 (with rear heated seat),

through BCM terminal 16

to display control unit (illumination) terminal 14 (with display control unit)

to display unit (illumination) terminal 4 (without display control unit).
Ground is supplied

to glove box lamp terminal 2

to A/T device illumination terminal 2 (with A/T)

to CVT device illumination terminal 2 (with CVT)

to rear sunshade front switch (illumination) terminal 6 (with rear sunshade)

to VDC off switch (illumination) terminal 4 (with VDC)

to door mirror remote control switch (illumination) terminal 15

to hazard switch (illumination) terminal 4

to headlamp washer switch (illumination) terminal 4

to cigarette lighter socket terminal 1

to headlamp aiming switch (illumination) terminal 4 (without xenon headlamp)

to A/C and AV switch (illumination) terminal 15

to display control unit (illumination) terminal 3 (with display control unit)

to display unit (illumination) terminal 6 (without display control unit)

to front heated seat switch (driver side) (illumination) terminal 6

to front heated seat switch (passenger side) (illumination) terminal 6

to front air massage seat switch (illumination) terminal 6 (with air massage seat)

to front door armrest illumination (driver side) terminal 2 and

to front door armrest illumination (passenger side) terminal 2

through grounds M71 and M72,

to CD auto changer (illumination) (with CD auto changer) and

to Audio unit (illumination)

through case ground,

to rear door armrest illumination LH terminal 2

to rear sunshade rear switch (illumination) terminal 9 (with rear center armrest switches)

to rear audio control switch (illumination) terminal 18 (with rear center armrest switches)

LT-260
ILLUMINATION

Bulb ReplacementBKS001RO
ASHTRAY ILLUMINATION
1. Remove front side ashtray. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Turn bulb socket left to release lock and remove it.
GLOVE BOX LAMP
1. Remove instrument passenger lower panel. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Turn bulb socket left to release lock and remove it.
CIGARETTE LIGHTER ILLUMINATION
1. Remove ashtray. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove screws from rearward of cigarette lighter socket.
3. Open hooks and remove bulb socket.
CAUTION:
When replacing bulb, replace assembly together with illumination ring.Ashtray illumination : 13.5V - 1.2W
Glove box lamp : 14V - 1.4W
Cigarette lighter illumination : 12V - 1.4W

BULB SPECIFICATIONS
LT-261
C
D
E
F
G
H
I
J
L
MA
B
LT

BULB SPECIFICATIONSPFP:26297
HeadlampBKS001RS
Exterior LampBKS001RT
Interior Lamp/IlluminationBKS001RU
Item Wattage (W)
Low/High (Xenon type)35 (D2S)
Low (Halogen type)55 (H11)
High (Halogen type)55 (H7)
Item Wattage (W)
Front combination lamp (Xenon type)Front turn signal lamp 21 (amber)
Parking lamp 5
Bending lamp 55 (H7)
Front combination lamp (Halogen type)Front turn signal lamp 21 (amber)
Parking lamp 5
Rear combination lampStop lamp LED
Tail lamp 5
Rear turn signal lamp 21
Back-up lamp 21
Rear fog lamp 21
Side turn signal lamp5
Front fog lamp35 (H8)
License plate lamp5
High-mounted stop lampLED
Item Wattage (W)
Map lamp8
Personal lamp8
Trunk room lamp3.4
Ashtray illumination1.4
Step lamp2.7
Vanity mirror lamp1.8
Ignition key hole illumination1.4
Glove box lamp1.4
Cigarette lighter illumination1.4