2003 NISSAN TEANA Page

BL-98
INTELLIGENT KEY SYSTEM

HAZARD REMINDER FUNCTION MALFUNCTION
NOTE:

Before performing the diagnosis in the following table, check “Diagnosis Procedure”. Refer to BL-91,
"Diagnosis Procedure" .

Make sure that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis,
and check each symptom.

If the following “symptoms” are detected, check systems shown in the “Diagnoses service procedure” col-
umn in this order.
Conditions of Vehicle (Operating Conditions)

Intelligent key function (I-KEY FUNCTION) is ON when setting on CONSULT-II.

Key reminder function (ANSWER BACK FUNCTION) is ON when setting on CONSULT-II.

Mechanical key is not inserted into ignition knob.

Ignition knob is not depressed.

All doors are closed.
ENGINE START FUNCTION MALFUNCTION
Intelligent Key Operation Inspection
NOTE:

Before performing the diagnosis in the following table, check “Diagnosis Procedure”. Refer to BL-91,
"Diagnosis Procedure" .

Make sure that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis,
and check each symptom.

If the following “symptoms” are detected, check systems shown in the “Diagnoses service procedure” col-
umn in this order.
Conditions of Vehicle (Operating Conditions)

Intelligent key function (I-KEY FUNCTION) is ON when setting on CONSULT-II.

Mechanical key is not inserted into ignition knob.

There is one or more registered Intelligent Key in the detection area of inside key antenna.
Mechanical Key Operation Inspection
NOTE:

Before performing the diagnosis in the following table, check “Diagnosis Procedure”. Refer to BL-91,
"Diagnosis Procedure" .

Make sure that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis,
and check each symptom.
Symptom Diagnoses service procedure Reference page
Hazard lamps do not flash during door lock
operation using Intelligent Key. (regardless of
whether Intelligent Key remote controller button
or request switch operation is used)1. Check key reminder settingBL-94
2. Replace BCMBCS-16
3. Replace Intelligent Key unitBL-117
Symptom Diagnoses service procedure Reference page
Ignition knob can not turn
This illuminate KEY warning lamp on com-
bination meter in red when ignition knob is
pressed.1. Check inside key antennaBL-114
2. Replace Intelligent Key unitBL-117
This illuminate KEY warning lamp on com-
bination meter in green when ignition knob
is pressed.Check steering lock unitBL-115
Ignition knob turns even without both Intelli-
gent Key and mechanical key.Replace steering lock unit —
This is not illuminate KEY warning lamp on
combination meter when ignition knob is
pressed.1. Check ignition knob switchBL-103
2. Check key switch (Intelligent Key unit input)BL-101
3. Replace Intelligent Key unitBL-117

INTELLIGENT KEY SYSTEM
BL-99
C
D
E
F
G
H
J
K
L
MA
B
BL


If the following “symptoms” are detected, check systems shown in the “Diagnoses service procedure” col-
umn in this order.
Conditions of Vehicle (Operating Conditions)

Registered mechanical key is used.

Do not keep 2 or more keys together. Remove the key you use from the key ring to prevent trouble.
WARNING CHIME FUNCTION MALFUNCTION
NOTE:

Before performing the diagnosis in the following table, check “Diagnosis Procedure”. Refer to BL-91,
"Diagnosis Procedure" .

Make sure that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis,
and check each symptom.

If the following “symptoms” are detected, check systems shown in the “Diagnoses service procedure” col-
umn in this order.
Conditions of Vehicle (Operating Conditions)

Intelligent key function (I-KEY FUNCTION) is ON when setting on CONSULT-II.

Each warning chime function is ON when setting on CONSULT-II.
Symptom Diagnoses service procedure Reference page
Ignition knob can not turn1. Check key switch (BCM input)BL-102
2. Replace BCMBCS-16
Symptom Diagnoses service procedure Reference page
Ignition switch return forgotten warning
does not sound.
(When Intelligent Key used)1. Check ignition knob switchBL-103
2. Replace Intelligent Key unitBL-117
3. Replace combination meterDI-25
Ignition key warning chime does not
sound.
(When mechanical key used)1. Check key switch (Intelligent Key unit input)BL-1012. Check key switch (BCM input)BL-102
3. Check door switchBL-105
4. Replace Intelligent Key unitBL-117
5. Replace combination meterDI-25
Ignition knob OFF position warning
chime (for inside vehicle) does not
sound.1. Check ignition knob switchBL-103
2. Replace Intelligent Key unitBL-117
3. Replace combination meterDI-25
Ignition knob OFF position warning
chime (for outside vehicle: after door
open/closed) does not sound.1. Check ignition knob switchBL-103
2. Check Intelligent Key warning buzzerB L - 111
3. Replace Intelligent Key unitBL-117
Intelligent Key take out warning chime
(when door open/closed) does not
sound.1. Check door switchBL-1052. Check inside key antennaBL-114
3. Check Intelligent Key warning buzzerB L - 111
4. Replace Intelligent Key unitBL-117
Intelligent Key take out warning chime
(through window) does not sound 1. Check inside key antennaBL-1142. Check Intelligent Key warning buzzerB L - 111
3. Replace Intelligent Key unitBL-117
4. Replace combination meterDI-25
Door lock non-operation warning does
not sound.1. Check Intelligent Key warning buzzerB L - 111
2. Replace Intelligent Key unitBL-117

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
BR-5
C
D
E
G
H
I
J
K
L
MA
B
BR

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Troubleshooting ChartBFS000BF
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: ApplicableReference page
BR-26
, BR-33
BR-26
, BR-33
BR-26
, BR-33—
—
BR-32, BR-39—
—
—
BR-32, BR-39
NVH in FAX, RAX and FSU, RSU section
NVH in WT section
NVH in WT section
NVH in FAX section
NVH in PS section
Possible cause and
suspected parts
Pads - damaged
Pads - uneven wear
Shims damaged
Rotor imbalance
Rotor damage
Rotor runout
Rotor deformation
Rotor deflection
Rotor rust
Rotor thickness variation
AXLE AND SUSPENSION
TYRES
ROAD WHEEL
DRIVE SHAFT
STEERING
Symptom BrakeNoise××× ×××
××
Shake× ×××
××
Shimmy, Judder×××××××××× ×

BRC-6
[ABS]
SYSTEM DESCRIPTION

EBD

Electronic Brake Distribution is a function that detects subtle slippages between front and rear wheels dur-
ing braking, and it improves handling stability by electronically controlling Brake Fluid Pressure which
results in reduced rear wheel slippage.

In case of electrical system break down, the fail-safe function is activated, EBD and ABS becomes inoper-
ative, and ABS warning lamp and brake warning lamp are turned on.

Electrical system diagnosis by CONSULT-II is available.

During EBD operation, brake pedal lightly vibrates and a mechanical noise may be heard. This is normal.

Just after starting vehicle after ignition switch ON, brake pedal may vibrate or motor operating sound may
be heard from engine compartment. This is a normal condition of operation check.

Stopping distance may be longer than that of vehicles without EBD when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.
Fail-Safe FunctionBFS000CR
ABS, EBD SYSTEM
In case of electrical malfunctions with ABS, ABS warning lamp will turn on. In case of electrical malfunctions
with EBD, brake warning lamp and ABS warning lamp will turn on. Simultaneously, ABS become one of follow-
ing conditions of the fail-safe function.

For ABS malfunction, only EBD is activated and condition of vehicle is same condition of vehicles without
ABS system.
NOTE:
ABS self-diagnosis sound may be heard. That is a normal condition because a self-diagnosis for Ignition
switch ON and The first starting are being performed.

For EBD malfunction, EBD and ABS become inoperative, and condition of vehicle is same as condition of
vehicles without ABS, EBD system.
Hydraulic Circuit DiagramBFS000CS
SFIA2082E

BRC-42
[VDC/TCS/ABS]
SYSTEM DESCRIPTION

ABS

The Anti-Lock Brake System is a function that detects wheel revolution while braking, and it improves
handling stability during sudden braking by electrically preventing 4 wheel lock. Maneuverability is also
improved for avoiding obstacles.

If the electrical system breaks down, then the fail-safe function is activated, ABS becomes inoperative,
and ABS warning lamp turns on.

Electrical system diagnosis by CONSULT-II is available.

During ABS operation, brake pedal lightly vibrates and a mechanical noise may be heard. This is normal.

Just after starting vehicle after ignition switch ON, brake pedal may vibrate or motor operating noise may
be heard from engine room. This is a normal status of operation check.

Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.
EBD

Electronic Brake Distribution is a function that detects subtle slippages between front and rear wheels dur-
ing braking, and it improves handling stability by electronically controlling Brake Fluid Pressure which
results in reduced rear wheel slippage.

In case of electrical system break down, the fail-safe function is activated, EBD and ABS becomes inoper-
ative, and ABS warning lamp and brake warning lamp are turned on.

Electrical system diagnosis by CONSULT-II is available.

During EBD operation, brake pedal lightly vibrates and a mechanical noise may be heard. This is normal.

Just after starting vehicle after ignition switch ON, brake pedal may vibrate or motor operating sound may
be heard from engine compartment. This is a normal condition of operation check.

Stopping distance may be longer than that of vehicles without EBD when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.
Fail-Safe FunctionBFS000DU
VDC/TCS SYSTEM
In the event an electrical malfunction occurs in the system, the VDC OFF indicator lamp and SLIP indicator
lamp in the combination meter will light up. At the same time, the VDC/TCS control is not performed, and the
vehicle is in the same conditions as a vehicle not equipped with the VDC/TCS function. However, the ABS
control operates normally.
If a malfunction is detected in the throttle control system, the VDC/TCS control is not performed and only the
ABS control operates normally.
CAUTION:
If fail-safe mode is initiated, perform self-diagnosis for the VDC/TCS/ABS control system.
ABS, EBD SYSTEM
In the event there is a malfunction with the electrical system, the ABS warning lamp, VDC OFF indicator lamp,
and SLIP indicator lamp will turn on when it is the ABS that is malfunctioning, and the brake warning lamp,
ABS warning lamp, VDC OFF indicator lamp, and SLIP indicator lamp will turn on when it is the EBD that is
malfunctioning. At the same time, the VDC/TCS/ABS will become one of the following conditions by the fail-
safe function.

When the ABS malfunctions, only the EBD operates. The condition is the same as that of models with
VDC/TCS/ABS.
NOTE:
ABS self-diagnosis sound may be heard. That is a normal condition because a self-diagnosis for “Ignition
switch ON” and “The first starting” are being performed.

When the EBD malfunctions, the EBD and ABS will not operate. The condition is the same as that of mod-
els without VDC/TCS/ABS and EBD.

CVT-6
INDEX FOR DTC

INDEX FOR DTCPFP:00024
Alphabetical Index BCS001FM
NOTE:
If DTC “U1000 CAN COMM CIRCUIT” is displayed with other DTC s, first perform the trouble diagnosis
for “DTC U1000 CAN COMMUNICATION LINE”. Refer to CVT-53
.
Items
(CONSULT-II screen terms) DTC Reference page
A/T TCC S/V FNCTN P0744 CVT-94
ATF TEMP SEN/CIRC P0710CVT-69
BELT DAMGP0730CVT-87
BRAKE SW/CIRC P0703CVT-60
CAN COMM CIRCUIT U1000CVT-53
CVT SPD SEN/FNCTN P1723CVT-143
ENGINE SPEED SIG P0725CVT-85
ELEC TH CONTROL P1726CVT-145
ESTM VEH SPD SIG P1722CVT-141
INPUT SPD SEN/CIRC P0715CVT-74
L/PRESS CONTROL P1745CVT-152
L/PRESS SOL/CIRC P0745CVT-97
LU-SLCT SOL/CIRC P1740CVT-147
MANUAL MODE SWITCH P0826CVT-113
PNP SW/CIRCP0705CVT-62
PRESS SEN/FNCTN P0841CVT-123
PRS CNT SOL/A FCTN P0746CVT-102
PRS CNT SOL/B CIRC P0778CVT-108
PRS CNT SOL/B FCTN P0776CVT-105
SEC/PRESS DOWN P0868CVT-131
STARTER RELAY/CIRC P0615CVT-56
STEP MOTR CIRC P1777CVT-153
STEP MOTR/FNCTN P1778CVT-157
TCC SOLENOID/CIRC P0740CVT-89
TCM-POWER SUPPLY P1701CVT-134
TP SEN/CIRC A/T P1705CVT-139
TR PRS SENS/A CIRC P0840CVT-118
TR PRS SENS/B CIRC P0845CVT-126
VEH SPD SEN/CIR AT P0720CVT-79

INDEX FOR DTC
CVT-7
D
E
F
G
H
I
J
K
L
MA
B
CVT

DTC No. Index BCS001FN
NOTE:
If DTC “U1000 CAN COMM CIRCUIT” is displayed with other DTC s, first perform the trouble diagnosis
for “DTC U1000 CAN COMMUNICATION LINE”. Refer to CVT-53
.
DTCItems
(CONSULT-II screen terms)Reference page
P0615 STARTER RELAY/CIRCCVT-56
P0703 BRAKE SW/CIRCCVT-60
P0705 PNP SW/CIRCCVT-62
P0710 ATF TEMP SEN/CIRCCVT-69
P0715 INPUT SPD SEN/CIRCCVT-74
P0720 VEH SPD SEN/CIR ATCVT-79
P0725 ENGINE SPEED SIGCVT-85
P0730 BELT DAMGCVT-87
P0740 TCC SOLENOID/CIRCCVT-89
P0744 A/T TCC S/V FNCTNCVT-94
P0745 L/PRESS SOL/CIRCCVT-97
P0746 PRS CNT SOL/A FCTNCVT-102
P0776 PRS CNT SOL/B FCTNCVT-105
P0778 PRS CNT SOL/B CIRCCVT-108
P0826 MANUAL MODE SWITCHCVT-113
P0840 TR PRS SENS/A CIRCCVT-118
P0841 PRESS SEN/FNCTNCVT-123
P0845 TR PRS SENS/B CIRCCVT-126
P0868 SEC/PRESS DOWNCVT-131
P1701 TCM-POWER SUPPLYCVT-134
P1705 TP SEN/CIRC A/TCVT-139
P1722 ESTM VEH SPD SIGCVT-141
P1723 CVT SPD SEN/FNCTNCVT-143
P1726 ELEC TH CONTROLCVT-145
P1740 LU-SLCT SOL/CIRCCVT-147
P1745 L/PRESS CONTROLCVT-152
P1777 STEP MOTR CIRCCVT-153
P1778 STEP MOTR/FNCTNCVT-157
U1000 CAN COMM CIRCUITCVT-53

TROUBLE DIAGNOSIS
CVT-43
D
E
F
G
H
I
J
K
L
MA
B
CVT

CONSULT-II Function (TRANSMISSION)BCS001GQ
CONSULT-II can display each diagnostic item using the diagnostic test modes shown below.
FUNCTION
CONSULT-II REFERENCE VALUE
Diagnostic test mode Function Reference page
Work supportThis mode enables a technician to adjust some devices faster and more accurately by
following the indications on CONSULT-II.CVT-45
Self-diagnostic results Self-diagnostic results can be read and erased quickly.CVT-47
Data monitor Input/Output data in the TCM can be read.CVT-50
CAN diagnostic support
monitorThe results of transmit/receive diagnosis of CAN communication can be read.CVT-52
CALIB dataCharacteristic information for TCM and CVT assembly can be read. Do not use, but
displayed.—
Function testPerformed by CONSULT-II instead of a technician to determine whether each system
is “OK” or “NG”.—
ECU part number TCM part number can be read. —
Item name Condition Display value (Approx.)
VSP SENSOR
During drivingApproximately matches the speedometer
reading
ESTM VSP SIG
PRI SPEED SEN During driving (lock-up ON) Approximately matches the engine speed
ENG SPEED SIG Engine running Closely matches the tachometer reading
SEC HYDR SEN “N” position idle 1.0 V
PRI HYDR SEN “N” position idle 0.7 - 3.5 V
ATF TEMP SENWhen CVT fluid temperature is 20°C (68°F) 2.0 V
When CVT fluid temperature is 80°C (176°F) 1.0 V
VIGN SEN Ignition switch: ON Battery voltage
VEHICLE SPEED During drivingApproximately matches the speedometer
reading
PRI SPEED During driving (lock-up ON) Approximately matches the engine speed
SEC SPEED During driving45 X Approximately matches the speed-
ometer reading
ENG SPEED Engine running Closely matches the tachometer reading
GEAR RATIO During driving 2.37 - 0.43
ACC PEDAL OPENReleased accelerator pedal - Fully depressed
accelerator pedal0.0/8 - 8.0/8
SEC PRESS “N” position idle 0.5 MPa
PRI PRESS “N” position idle 0.3 - 0.7 MPa
STM STEP During driving−20 step - 190 step
ISOLT1Lock-up “OFF” 0.0 A
Lock-up “ON” 0.7 A
ISOLT2Release your foot from the accelerator pedal 0.8 A
Press the accelerator pedal all the way down 0.0 A
ISOLT3Secondary pressure low - Secondary pressure
high0.8 - 0.0 A
SOLMON1Lock-up “OFF” 0.0 A
Lock-up “ON” 0.6 - 0.7 A