2003 NISSAN TEANA Power

POWER STEERING OIL PUMP
PS-37
C
D
E
F
H
I
J
K
L
MA
B
PS

ASSEMBLY
NOTE:
Secure oil pump in a vise if necessary.
CAUTION:
Use copper plates when securing in a vise.
1. Apply recommended grease to oil seal lips. Apply recommended
fluid to around oil seal, and then install oil seal to body assembly
using the drift [SST].
2. If dowel pin has been removed, insert it into body assembly by
hand. If cannot be inserted by hand, lightly tap with a hammer.
3. Install flow control valve A, flow control valve spring and flow
control valve B assembly as shown in the figure.
4. Install front side plate (3) with dowel pin (2) on flow control valve
A (1) side as shown in the figure aligning with front side plate
cutout (A) to body assembly (4).
5. Install cam ring as shown in the figure.
6. Install pulley to body assembly.
CAUTION:
Do not damage oil seal when installing pulley.
STC0914D
SGIA0526E
SGIA1189E
SGIA0612E

PS-38
POWER STEERING OIL PUMP

7. Install rotor so that mark faces body assembly side, and then
install it to pulley shaft.
8. Install vane to rotor so that arc of vane faces cam ring side.
9. Install rotor snap ring to slit of pulley shaft using a hammer and a
10 mm (0.39 in) socket.
CAUTION:

Do not damage rotor and pulley shaft.

Power steering oil pump must be replaced if rotor is dam-
aged.
10. Install rear side plate with dowel pin A on flow control valve A
side as shown in the figure aligning with rear side plate cutout B
to cartridge.
11. Apply recommended fluid to O-ring, and then Install O-ring to
body assembly.
12. Apply recommended fluid to O-ring, and then install O-ring to
rear side plate.
13. Apply recommended fluid to Teflon ring, and then install Teflon
ring to rear side plate.
14. Install rear cover to body assembly, and then tighten mounting
bolts to the specified torque.
15. Apply recommended fluid to O-ring, and then install O-ring to body assembly.
16. Install suction pipe to body assembly.
17. Install rear bracket to rear cover, and then tighten mounting bolts to the specified torque.
18. Install front bracket to body assembly, and then tighten mounting bolts to the specified torque.
SGIA0874E
SGIA0613E
SGIA0063E
SGIA0530E

HYDRAULIC LINE
PS-39
C
D
E
F
H
I
J
K
L
MA
B
PS

HYDRAULIC LINEPFP:49721
Removal and InstallationBGS00041
COMPONENTS (EXCEPT FOR QR20DE MODELS)
1. Reservoir tank 2. Reservoir tank bracket 3. Suction hose
4. Oil pump assembly 5. High pressure hose 6. Steering gear assembly
7. Low pressure piping 8. High pressure piping 9. O-ring
10. Clamp 11. Copper washer 12. Eye-joint (assembled to high pres-
sure side hose)
13. Pressure sensor 14. Eye-bolt
Refer to GI-10, "
Components" , and the followings for the symbols in the figure.
: Apply power steering fluid.
SGIA1621E

PS-40
HYDRAULIC LINE

COMPONENTS (QR20DE MODELS)
CAUTION:

Securely insert harness connector to pressure sensor.
1. Reservoir tank 2. Reservoir tank bracket 3. Suction hose
4. Oil pump assembly 5. High pressure hose 6. Steering gear assembly
7. Low pressure piping 8. High pressure piping 9. O-ring
10. Eye-bolt 11. Copper washer 12. Eye-joint (assembled to high pres-
sure side hose)
13. Pressure sensor 14. Clamp
Refer to GI-10, "
Components" , and the followings for the symbols in the figure.
: Apply power steering fluid.
SGIA1622E

RF-1
ROOF
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION RF
A
B
RF

ROOF
PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
Precautions .............................................................. 2
PREPARATION ........................................................... 3
Commercial Service Tools ........................................ 3
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 4
Work Flow ................................................................ 4
CUSTOMER INTERVIEW ..................................... 4
DUPLICATE THE NOISE AND TEST DRIVE ....... 5
CHECK RELATED SERVICE BULLETINS ........... 5
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 5
REPAIR THE CAUSE ........................................... 5
CONFIRM THE REPAIR ....................................... 6
Generic Squeak and Rattle Troubleshooting ........... 6
INSTRUMENT PANEL .......................................... 6
CENTER CONSOLE ............................................. 6
DOORS ................................................................. 6
TRUNK .................................................................. 7
SUNROOF/HEADLINING ..................................... 7
SEATS ................................................................... 7
UNDERHOOD ....................................................... 7
Diagnostic Worksheet .............................................. 8
SUNROOF ................................................................ 10
Component Parts and Harness Connector Location ... 10
System Description ................................................. 11
TILT UP / SLIDE CLOSE OPERATION ................ 11
TILT DOWN / SLIDE OPEN OPERATION ........... 11AUTO OPERATION ............................................. 11
TIMER FUNCTION .............................................. 11
ANTI-PINCH FUNCTION .................................... 11
MEMORY RESET PROCEDURE ....................... 12
INITIALIZATION PROCEDURE .......................... 12
Wiring Diagram — SROOF — ................................ 13
Terminals and Reference Value for BCM ............... 14
Terminals and Reference Value for Sunroof Motor
Assembly ................................................................ 14
Work Flow ............................................................... 15
Trouble Diagnosis Chart by Symptom .................... 15
Check BCM Power Supply and Ground Circuit ...... 15
Check Sunroof Motor Assembly Power Supply and
Ground Circuit ........................................................ 16
Check Sunroof Switch System ............................... 17
Check Driver Side Door Switch .............................. 19
Wind Deflector Inspection ....................................... 21
Link and Wire Assembly ......................................... 21
Fitting Adjustment ................................................... 21
LID WEATHERSTRIP OVERLAP ADJUST-
MENT AND SURFACE FLASHNESS ADJUST-
MENT .................................................................. 22
Removal and Installation ........................................ 22
SUNROOF UNIT ASSEMBLY ............................. 24
GLASS LID .......................................................... 25
WEATHERSTRIP OF GLASS LID ....................... 26
SUNSHADE ........................................................ 26
WIND DEFLECTOR ............................................ 26
SUNROOF MOTOR ASSEMBLY ........................ 27
LINK ASSEMBLY AND WIRE ASSEMBLY ......... 27

SUNROOF
RF-11
C
D
E
F
G
H
J
K
L
MA
B
RF

System DescriptionBIS0010S
Power supplied at all time

through 50A fusible link (letter M , located in the fuse and fusible link box)

to BCM terminal 55

through 15A fuse [No.17, located in the fuse block (J/B)]

to BCM terminal 42

through BCM terminal 54

to sunroof motor assembly terminal 6.
With ignition switch ON or START position,
Power is supplied

through 10A fuse [No.1, located in the fuse block (J/B)]

to BCM terminal 38

through BCM terminal 53

to sunroof motor assembly terminal 3.
Ground is supplied

to BCM terminal 52

to sunroof motor assembly terminal 2

through body grounds M71, M72.
TILT UP / SLIDE CLOSE OPERATION
When tilt up / slide close switch is pressed,
Ground is supplied

to sunroof motor assembly terminal 5

through sunroof switch terminal 3

through sunroof switch terminal 2

through body grounds M71, M72.
Then, the sunroof tilt up / slide close.
TILT DOWN / SLIDE OPEN OPERATION
When tilt down / slide open switch is pressed,
Ground is supplied

to sunroof motor assembly terminal 1

through sunroof switch terminal 1

through sunroof switch terminal 2

through body grounds M71, M72.
Then, the sunroof tilt down / slide open.
AUTO OPERATION
The power sunroof AUTO feature makes it possible to slide open and slide close or tilt up and tilt down the
sunroof without holding the sunroof switch in the slide open or slide close / tilt up or tilt down position.
TIMER FUNCTION
When the ignition switch is turned to OFF position from ON or START position, timer operates for 15 minutes.
Sunroof can be operated for 15 minutes.
Timer operation is canceled when one of the following conditions is satisfied.

ignition switch : OFF→ ON

front door switch (driver side) : ON (Open)→OFF (Closed)
ANTI-PINCH FUNCTION
The CPU of sunroof motor monitors the sunroof motor operation and the sunroof position (fully-closed or
other) by the signals from sunroof motor.
When sunroof motor detects an interruption during the following slide close and tilt down operation, sunroof
motor controls the sunroof motor for open and the sunroof will operate until full up position (during tilt down
operation) or 125 mm (4.92 in) or more in an open direction (during slide close operation)

RF-12
SUNROOF

The operation condition is the following.

automatic close operation and tilt down when ignition switch is in the ON position

automatic close operation and tilt down during retained power operation.
MEMORY RESET PROCEDURE
1. Please observe the following instructions while confirming the sunroof operation.
NOTE:
Do not disconnect the electronic power while the sunroof is operating or within 5 seconds after the sunroof
stops.
2. Initialization of system should be conducted after the following conditions.

When the battery is out or connector is disconnected while sunroof is operating or within 5 seconds
after sunroof stops.

When the sunroof motor is changed.

When the sunroof does not operate normally. (Incomplete initialization conditions)
INITIALIZATION PROCEDURE
If the sunroof does not close or open automatically, use the following procedure to return sunroof operation to
normal.
1. Press and hold the switch to the CLOSE/UP side for approximately 10 seconds.
2. The glass lid will move toward tilt up direction and will be stopped mechanically, and then it will be auto-
matically fully closed. Then glass lid will be automatically operated in sequence of “tilt up” → “tilt down” →
“slide open” → “slide close”. (Keep pressing the switch during this operation)
3. After the glass lid stops, release the switch after 5 seconds.
4. If sunroof switch operates normally, this initialization is done.

RF-14
SUNROOF

Terminals and Reference Value for BCMBIS0010U
Terminals and Reference Value for Sunroof Motor AssemblyBIS0010V
Te r m i n a lWire
colorItemSignal
Input/OutputConditionVoltage (V)
(Approx.)
38 RIgnition switch ON power supply
(ON or START)Input Ignition switch (ON or START position) Battery voltage
42 Y/R Power source (Fuse) Input — Battery voltage
52 B Ground — — 0
53 L/W RAP signal OutputIgnition switch ON Battery voltage
Within 15 minutes after ignition switch is
turned to OFF positionBattery voltage
When front door (driver side) is open in
retained power is operates.0
54 R/Y Power window power supply Output — Battery voltage
55 W/B Power source (Fusible link) Input — Battery voltage
62 SBFront door switch driver side
signalInputOPEN (ON) 0
CLOSE (OFF) Battery voltage
Te r m i -
nalWire
colorItemSignal
Input/OutputConditionVoltage (V)
(Approx.)
1L/BSunroof (BIT 3) switch
signalInputIgnition switch ON and sunroof switch
in TILT DOWN / SLIDE OPEN position0
Other than above Battery voltage
2 B Ground — — 0
3 G/R Timer signal InputIgnition switch ON Battery voltage
Within 15 minutes after ignition switch
is turned to OFF positionBattery voltage
When front door (driver side) is open in
retained power is operates0
4GVehicle speed signal
(2-pulse)InputSpeedometer operated [When vehicle
speed is approx. 40 km/h (25 MPH)]
5L/RSunroof (BIT 4) switch
signalInputIgnition switch ON and sunroof switch
in TILT UP / SLIDE CLOSE position0
Other than above Battery voltage
6W/BPower window power
supply Input — Battery voltage
ELF1080D