2003 LEXUS LS430 replacement

REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order. However, only installation
procedures requiring additional information are included.
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
1.REMOVE FRONT DOOR BELT MOLDING ASSY LH (See REPLACEMENT
)
2.REMOVE FRONT DOOR GLASS RUN LH
a. Remove the glass run from the front door window frame.
3.REMOVE FRONT DOOR WINDOW FRAME MOLDING REAR LH
a. Remove the 3 screws and molding.
Fig. 69: Removing Front Door Window Frame Molding Rear LH

REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order. However, only installation
procedures requiring additional information are included.
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
1.REMOVE REAR DOOR BELT MOLDING ASSY LH (See REPLACEMENT
)
2.REMOVE REAR DOOR GLASS RUN LH
a. Remove the glass run from the rear door window frame.
3.REMOVE REAR DOOR WINDOW FRAME MOLDING FRONT LH
a. Remove the 3 screws and moldin
g.

REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order.
A bolt without torque specification is a standard bolt (see SPECIFIED TORQUE FOR STANDARD
BOLTS ).
1.REMOVE REAR COMBINATION LAMP SERVICE COVER RH (See OVERHAUL
)
2.REMOVE REAR COMBINATION LAMP SERVICE COVER LH (See OVERHAUL
)
3.REMOVE LUGGAGE COMPARTMENT LAMP ASSY NO. (See step 4 in OVERHAUL
)
4.REMOVE BACK DOOR TRIM COVER (See step 5 in OVERHAUL
)
5.REMOVE LUGGAGE COMPARTMENT DOOR GARNISH SUB-ASSY OUTSIDE
a. Remove the 6 nuts and key cylinder. Then remove the luggage compartment door opener switch.
b.Disengage the 4 clips and remove the garnish from the luggage compartment door.

Fig. 84: Removal And Installation Of Rood Drip Side Finish Molding
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REPLACEMENT
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
When replacing the molding, heat the body and molding using a heat light.

Fig. 88: Removing And Installing Wheel Opening Molding
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order.
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
1.REMOVE FRONT FENDER WHEEL OPENING MOLDING LH
a. Remove the 4 screws and molding.

Fig. 99: Connecting Battery Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Reverse the polarity and check that the rear sunshade moves down.
If all the check results are as specified above and normal wire harness is confirmed, replace the rear
sunshade control relay (see REPLACEMENT
).
REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order. However, only installation
procedures requiring additional information are included.
A bolt without a torque specification is shown in the standard bolt chart (see SPECIFIED TORQUE
FOR STANDARD BOLTS ).

1.REMOVE PACKAGE TRAY TRIM PANEL ASSY (See REPLACEMENT )
a. Remove the rear door scuff plate LH and RH.
b. Remove the rear door opening trim weatherstrip LH and RH.
c. Remove the rear seat side cover LH and RH.
d. Remove the roof side garnish inner LH and RH.
e. Remove the rear speaker grille.
f. Remove the package tray trim panel.
2.REMOVE PACKAGE TRAY TRIM PANEL ASSY NO. 2 (See REPLACEMENT
)
a. Remove the center stop lamp.
b. Remove the package tray trim panel.
3.REMOVE REAR SUNSHADE
a. Disconnect the connector.
b. Remove the 6 bolts.
c. Remove the sunshade.
Fig. 100: Removing Rear Sunshade

REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order.
A bolt without a torque specification is shown in the standard bolt chart (see SPECIFIED TORQUE
FOR STANDARD BOLTS ).
1.REMOVE FRONT SEAT ASSY LH (See OVERHAUL
)
2.REMOVE FRONT SEAT ASSY RH (See OVERHAUL
)
3.REMOVE REAR SEAT CUSHION ASSY (FIXED TYPE REAR SEAT) (See OVERHAUL
)
4.REMOVE REAR SEATBACK ASSY (FIXED TYPE REAR SEAT) (See step 4 in OVERHAUL
)
5.REMOVE REAR SEAT CUSHION ASSY LH (POWER ADJUSTER TYPE) (See OVERHAUL
)
6.REMOVE REAR SEAT CUSHION ASSY RH (POWER ADJUSTER TYPE) (See OVERHAUL
)
7.REMOVE REAR SEAT ASSY LH (POWER ADJUSTER TYPE) (See OVERHAUL
)
8.REMOVE REAR SEATBACK ASSY (POWER ADJUSTER TYPE) (See OVERHAUL
)
9.REMOVE FRONT DOOR SCUFF PLATE LH
a. Using a screwdriver, disengage the 4 claws and 4 clips, and remove the scuff plate.
HINT:
Tape the screwdriver tip before use.