2003 LEXUS LS430 replacement

<0029004c004a0011000300140015001d000300350048005000520059004c0051004a00030024005100470003002c0051005600570044004f004f004c0051004a0003003500480044005500030025005800500053004800550003000b001500030032004900
030015000c[
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REPLACEMENT

Fig. 13: Removing Rear Floor Finish Plate
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
6.REMOVE TOOL CASE
7.REMOVE SIDE TRIM TOOL BAG COVER
a. Using a screwdriver, disengage the 2 claws and 2 clips and remove the cover.
HINT:
Tape the screwdriver tip before use.
Fig. 14: Removing Side Trim Tool Bag Cover

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
8.REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSY LH (See REPLACEMENT
)
9.REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSY RH (See REPLACEMENT
)
10.REMOVE QUARTER PANEL MUDGUARD SUB-ASSY REAR LH (W/ MUDGUARD)
a. Remove the 4 screws and mud
guard.

Fig. 19: Installing Rear Bumper Side Retainer LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
34.INSTALL REAR BUMPER SIDE RETAINER RH
HINT:
Use the same procedures described for the LH side.
REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order. However, only installation
procedures requiring additional information are included.
A bolt without a torque specification is shown in the standard bolt chart (see SPECIFIED TORQUE
FOR STANDARD BOLTS ).

Fig. 36: Removing And Installing Outside Molding
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REPLACEMENT
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.

Fig. 58: Removal And Installation of Rocker Panel Molding
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REPLACEMENT
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.

A bolt without a torque specification is shown in the standard bolt chart (see SPECIFIED TORQUE
FOR STANDARD BOLTS ).
When replacing the molding, heat the body and molding using a heat light.
Heating temperature:
HEATING TEMPERATURE CHART
1.REMOVE FRONT FENDER MUDGUARD SUB-ASSY LH (W/ MUDGUARD)
a. Remove the 3 screws and mudguard.
2.REMOVE FRONT FENDER OUTSIDE MOLDING LH (See REPLACEMENT
)
3.REMOVE ROCKER PANEL MOLDING FRONT LH
a. Remove the 5 screws and the 4 clips labeled A.
b.Using a molding remover, disengage the clip labeled B and remove the molding.
ItemTemperature
Body40 to 60°C (104 to 140°F)
molding20 to 30°C (68 to 86°F)

Fig. 66: Installing Rocker Panel Molding Front LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
7.INSTALL FRONT FENDER OUTSIDE MOLDING LH (See REPLACEMENT
)
8.INSTALL FRONT FENDER MUDGUARD SUB-ASSY LH (W/ MUDGUARD)
a. Install the front fender mudguard with the 3 screws.
REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order.
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
1.REMOVE POWER WINDOW REGULATOR SWITCH ASSY (See step 16 in OVERHAUL
)
2.REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH (See OVERHAUL
)
3.REMOVE FRONT DOOR TRIM BOARD SUB-ASSY LH (See OVERHAUL
)

REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order.
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
1.REMOVE DOOR INSIDE HANDLE BEZEL NO. 2 LH (See OVERHAUL
)
2.REMOVE REAR DOOR ARMREST BASE PANEL UPPER LH (See OVERHAUL
)
3.REMOVE SIDE TRIM BOARD COVER FRONT LH (See OVERHAUL
)
4.REMOVE SIDE REAR CURTAIN ASSY LH (See step 4 on OVERHAUL
)
5.REMOVE REAR DOOR TRIM BOARD SUB-ASSY LH (See step 5 on OVERHAUL
)
6.REMOVE REAR DOOR BELT MOLDING ASSY LH
a. Put protective tape under the molding.
b. Remove the screw.
c. Using a molding remover, pry out the molding as shown in Fig. 68
.
HINT:
Tape the remover tip before use.