2003 LEXUS LS430 replacement

REPLACEMENT
1.WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See PRECAUTION
)
2.DISCONNECT BATTERY NEGATIVE TERMINAL
3.REMOVE V-BANK COVER
a. Remove the 2 nuts and V-bank cover.
4.REMOVE AIR CLEANER INLET NO.1
5.REMOVE INTAKE AIR CONNECTOR PIPE
a. Disconnect the air hose and ventilation hose No. 1.
b. Loosen the hose clamp.
c. Remove the bolt and intake air connector pipe.
6.REMOVE V-BANK COVER BRACKET NO.1
7.REMOVE V-BANK COVER BRACKET NO.2
8.REMOVE V-BANK COVER BRACKET NO.3
9.REMOVE V-VANK COVER BRACKET NO.4
10.REMOVE VACUUM SWITCHING VALVE ASSY
11.DISCONNECT ENGINE WIRE

REPLACEMENT
1.WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See PRECAUTION
)
2.DISCONNECT BATTERY NEGATIVE TERMINAL
3.DRAIN FUEL (See PRECAUTION
)
4.REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSY LH (SEPARATED TYPE REAR
SEAT) (See OVERHAUL
)
5.REMOVE BENCH TYPE REAR SEAT CUSHION ASSY (FIXED TYPE REAR SEAT) (See
OVERHAUL
)
6.REMOVE REAR FLOOR SERVICE HOLE COVER NO.2
a. Remove the 3 cap nuts and service hole cover.
7.REMOVE FUEL TANK MAIN TUBE SUB-ASSY

Fig. 49: Exploded View Of Fuel Tank Assy Components
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REPLACEMENT

1.WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See PRECAUTION )
2.DISCONNECT BATTERY NEGATIVE TERMINAL
3.DRAIN FUEL (See PRECAUTION
)
4.REMOVE SEPARATE TYPE REAR SEAT CUSHION ASSY LH (SEPARATED TYPE REAR
SEAT) (See OVERHAUL
)
5.REMOVE BENCH TYPE REAR SEAT CUSHION ASSY (FIXED TYPE REAR SEAT) (See
OVERHAUL
)
6.REMOVE REAR FLOOR SERVICE HOLE COVER NO.2 (See REPLACEMENT
)
7.REMOVE FUEL TANK MAIN TUBE SUB-ASSY
a. Disconnect the connector in the fuel tank side.
1. Remove the tube joint clip.
2. Pull out the fuel main tube.
3. Plu
g the port of the fuel suction plate with a clean rubber cap.

Fig. 51: Pulling Out Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Protect each connecting part from damage and contamination by covering it with a vinyl bag.
8.REMOVE REAR FLOOR SERVICE HOLE COVER
a. Remove the service hole cover and disconnect the fuel sender gauge connector.
9.REMOVE FRONT FLOOR BRACE CENTER (See OVERHAUL
)
10.REMOVE ENGINE UNDER COVER NO.2
11.REMOVE EXHAUST PIPE ASSY (See REPLACEMENT
)
12.REMOVE PROPELLER SHAFT HEAT INSULATOR
13.REMOVE FRONT FLOOR HEAT INSULATOR NO.1
a. Remove the 2 bolts and propeller shaft heat insulator.
14.REMOVE DIFFERENTIAL SUPPORT PROTECTOR NO.1
15.REMOVE DIFFERENTIAL SUPPORT PROTECTOR NO.2
16.REMOVE PROPELLER SHAFT ASSY (See OVERHAUL
)
17.REMOVE PARKING BRAKE CABLE ASSY NO.2 (See REPLACEMENT
)
18.REMOVE PARKING BRAKE CABLE ASSY NO.3 (See REPLACEMENT
)
19.REMOVE FUEL TANK TO FILLER PIPE HOSE
20.REMOVE FUEL TANK EVAPORATION VENT TUBE
21.REMOVE FUEL TANK BREATHER HOSE

Fig. 55: Installing Fuel Sub-Suction Hose
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
37.INSTALL FUEL TANK VENT TUBE SET PLATE
a. Install the set plate with the 8 bolts.
Torque: 6.0 N.m (61 kgf.cm, 52 in..lbf)
38.INSTALL FUEL TANK ASSY
a. Install the fuel tank with the fuel tank band.
Torque: 39 N.m (400 kgf.cm, 29 ft.lbf)
39.INSTALL FUEL TANK BREATHER HOSE
40.INSTALL FUEL TANK EVAPORATION VENT TUBE
41.INSTALL FUEL TANK TO FILLER PIPE HOSE
42.INSTALL PARKING BRAKE CABLE ASSY NO.3 (See REPLACEMENT
)
43.INSTALL PARKING BRAKE CABLE ASSY NO.2 (See REPLACEMENT
)
44.INSTALL PROPELLER SHAFT ASSY (See OVERHAUL
)

45.INSTALL DIFFERENTIAL SUPPORT PROTECTOR NO.2
46.INSTALL DIFFERENTIAL SUPPORT PROTECTOR NO.1
47.INSTALL FRONT FLOOR HEAT INSULATOR NO.1
a. Install the front floor heat insulator with the 4 bolts.
Torque: 5.4 N.m (55 kgf.cm, 47 in..lbf)
48.INSTALL PROPELLER SHAFT HEAT INSULATOR
49.INSTALL EXHAUST PIPE ASSY (See REPLACEMENT
)
50.INSTALL ENGINE UNDER COVER NO.2
51.INSTALL FRONT FLOOR BRACE CENTER (See OVERHAUL
)
52.INSTALL REAR FLOOR SERVICE HOLE COVER
53.INSTALL FUEL TANK MAIN TUBE SUB-ASSY
a. Connect the connector on the fuel tank side.
1. Attach the fuel tube connector to the port of the fuel suction plate.
2. Install the tube joint clip.
b. Connect the connector on the fuel pipe side.
1. Insert the connector by aligning the axes of the pipe and the connector until the retainer makes a
click sound.

Fig. 56: Connecting Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
54.INSTALL REAR FLOOR SERVICE HOLE COVER NO.2 (See REPLACEMENT
)
55.INSTALL BENCH TYPE REAR SEAT CUSHION ASSY (FIXED TYPE REAR SEAT) (See
OVERHAUL
)
56.INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSY LH (SEPARATED TYPE REAR
SEAT) (See OVERHAUL
)
57.ADD FUEL (See PRECAUTION
)
58.CONNECT BATTERY NEGATIVE TERMINAL