2001 TOYOTA SEQUOIA terminal TC

H23917
H2391510 m (33 ft) or more SSTBattery
H23208
± SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
RS±29
3312 Author: Date:
2005 SEQUOIA (RM1146U)
(1) Tie the tires together with 2 wire harnesses.
CAUTION:
Make sure that the wire harness is tight. Looseness in the
wire harness results in the tires coming free due to the
shock when the airbag is deployed.
(f) Deploy the airbag.
(1) Connect the red clip of the SST to the battery posi-
tive (+) terminal and the black clip of the SST to the
battery negative (±) terminal.
(2) Check that no one is within a 10 m (33 ft) radius of
the disc wheel which the steering wheel pad is tied
to.
(3) Press the SST activation switch and deploy the air-
bag.
CAUTION:
When deploying the airbag, make sure that no one is near
the tire.
HINT:
The airbag is deployed as the LED of the SST activation switch
comes on.
(g) Dispose of the steering wheel pad.
CAUTION:

The steering wheel pad becomes extremely hot when
the airbag is deployed, so do not touch it for at least
30 minutes after deployment.

Use gloves and safety glasses when handling a steer-
ing wheel pad with a deployed airbag.

Do not apply water, etc. to a steering wheel pad with
a deployed airbag.

Always wash your hands with water after completing
the operation.
(1) Remove the steering wheel pad from the disc
wheel.
(2) Place the steering wheel pad in a plastic bag, tie it
tightly and dispose of it as other general part dispos-
al.

RS0BD±11
± SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
RS±31
3314 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
CAUTION:

If the steering wheel pad has been dropped, or there are cracks, dents or other defects in the
case or connector, replace the steering wheel pad with a new one.

When installing the steering wheel pad, take care it is not pinched between other parts.

Never use airbag parts from another vehicle. When replacing parts, replace them with new
ones.
1. INSTALL SPIRAL CABLE (SEE PAGE SR±23)
2. INSTALL STEERING COLUMN COVER LOWER (SEE PAGE SR±23)
3. INSTALL STEERING WHEEL (SEE PAGE SR±23)
4. INSTALL STEERING WHEEL PAD (SEE PAGE SR±23)
5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
6. PERFORM INITIALIZATION (SEE PAGE SR±23)
Some system need initialization when disconnecting the cable from the negative battery terminal.
7. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)

RS0T6±03
H23215
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT PASSENGER AIRBAG ASSEMBLY
RS±33
3316 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
NOTICE:

If the wiring connector of the SRS is disconnected
and the ignition switch is in the ON or ACC position,
DTCs will be recorded.

Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
1. PRECAUTION (SEE PAGE RS±1 and RS±3)
2. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the
airbag working.
3. REMOVE FRONT DOOR SCUFF PLATES
(SEE PAGE BO±89)
4. REMOVE COWL SIDE TRIM BOARDS
(SEE PAGE BO±89)
5. REMOVE SIDE PANELS (SEE PAGE BO±89)
6. REMOVE LOWER FINISH PANEL
(SEE PAGE BO±89)
7. REMOVE GLOVE COMPARTMENT DOOR
(SEE PAGE BO±89)
8. REMOVE LOWER NO. 2 FINISH PANEL
(SEE PAGE BO±89)
9. REMOVE SHIFTING HOLE COVER
(SEE PAGE BO±89)
10. REMOVE UPPER CONSOLE PANEL
(SEE PAGE BO±89)
11. REMOVE REAR CONSOLE BOX
(SEE PAGE BO±89)
12. REMOVE FRONT CONSOLE BOX
(SEE PAGE BO±89)
13. REMOVE LOWER INSTRUMENT COVER
(SEE PAGE BO±89)
14. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY
(a) Using a clip remover, disengage the connector clamp.
(b) Disconnect the airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(c) Remove the bolt holding the front passenger airbag as-
sembly and instrument panel.
(d) Remove the 2 bolts holding the front passenger airbag
assembly and instrument panel reinforcement.

AB0158
SSTBattery
H23215
H23216SST
R13455
10 m (33 ft) or more
SSTBattery
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT PASSENGER AIRBAG ASSEMBLY
RS±37
3320 Author: Date:
2005 SEQUOIA (RM1146U)
1. AIRBAG DEPLOYMENT WHEN SCRAPPING VE-
HICLE
(a) Check the function of the SST (see step 1±(a) on page
RS±23).
(b) Precaution (see page RS±1 and RS±3).
(c) Disconnect the cable from the negative battery terminal.
Wait for 90 seconds after disconnecting the cable to prevent the
airbag working.
(d) Remove the glove compartment door (see page
BO±89).
(e) Remove the lower No. 2 finish panel (see page
BO±89).
(f) Disconnect the airbag connector (yellow colored one)
from the front passenger airbag assembly.
(1) Using a clip remover, disengage the connector
clamp.
(2) Disconnect the airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(g) Install the SST.
(1) Connect the SST connector to the front passenger
airbag assembly.
SST 09082±00700, 09082±00780
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(2) Move the SST at least 10 m (33 ft) away from the ve-
hicle side window.
(3) Maintaining enough clearance for the SST wire har-
ness in the front side window, close all doors and
windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(4) Connect the red clip of the SST to the battery posi-
tive (+) terminal and the black clip of the SST to the
negative (±) terminal.

AB0152
SST
H23213
RS±38
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT PASSENGER AIRBAG ASSEMBLY
3321 Author: Date:
2005 SEQUOIA (RM1146U)
(h) Deploy the airbag.
(1) Check that no one is inside the vehicle or within a
10 m (33 ft) radius of the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
CAUTION:

When deploying the airbag, make sure that no one is
near the vehicle.

The front passenger airbag assembly becomes ex-
tremely hot when the airbag is deployed, so do not
touch it for at least 30 minutes after deployment.

Use gloves and safety glasses when handling a front
passenger airbag assembly with a deployed airbag.

Do not apply water, etc. to a front passenger airbag
assembly with a deployed airbag.

Always wash your hands with water after completing
the operation.
HINT:
The airbag deploys as the LED of the SST activation switch
comes on.
2. DEPLOYMENT WHEN DISPOSING OF FRONT PAS-
SENGER AIRBAG ASSEMBLY ONLY
NOTICE:

When disposing of the front passenger airbag assem-
bly, never use the customer's vehicle to deploy the
airbag.

Be sure to follow the procedure detailed below when
deploying the airbag.
HINT:
Prepare a battery as the power source to deploy the airbag.
(a) Check the function of the SST (see step 1±(a)).
(b) Remove the front passenger airbag assembly (see page
RS±33).
CAUTION:

When removing the front passenger airbag assembly,
work must be started 90 seconds after the ignition
switch is turned to the ºLOCKº position and the nega-
tive (±) terminal cable is disconnected from the bat-
tery.

When storing the front passenger airbag assembly,
keep the airbag deployment side facing upward.

H24665
Tires
(2 or more)
Tires
(2 or more)
H23917
H24672
Battery
SSTFront Passenger
Airbag Assembly
10 m (33 ft) or more
RS±40
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT PASSENGER AIRBAG ASSEMBLY
3323 Author: Date:
2005 SEQUOIA (RM1146U)
(d) Place the tires.
(1) Place at least 2 tires under the tire which the front
passenger airbag assembly is tied to.
(2) Place at least 2 tires over the tire which the front
passenger airbag assembly is tied to. The top tire
should have the disc wheel installed.
(3) Tie the tires together with 2 wire harness.
CAUTION:
Make sure that the wire harness is tight. Looseness in the
wire harness results in the tires coming free due to the
shock when the airbag is deployed.
(e) Install the SST.
Connect the SST connector.
SST 09082±00700, 09082±00780
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock. Also, se-
cure some slack for the SST wire harness inside the tire.
(f) Deploy the airbag.
(1) Connect the red clip of the SST to the battery posi-
tive (+) terminal and the black clip of the SST to the
battery negative (±) terminal.
(2) Check that no one is within a 10 m (33 ft) radius of
the tire which the front passenger airbag assembly
is tied to.
(3) Press the SST activation switch and deploy the air-
bag.
CAUTION:
When deploying the airbag, make sure that no one is near
the tire.
HINT:
The airbag deploys as the LED of the SST activation switch
comes on.

H23211
RS±44
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT PASSENGER AIRBAG ASSEMBLY
3327 Author: Date:
2005 SEQUOIA (RM1146U)
11. CONNECT AIRBAG CONNECTOR
(a) Connect the airbag connector as shown in the illustration.
(b) Attach the connector clamp to the reinforcement.
12. INSTALL COWL TRIM BOARDS
(SEE PAGE BO±97)
13. INSTALL FRONT DOOR SCUFF PLATES
(SEE PAGE BO±97)
14. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
15. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
16. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)

RS0TA±03
H24311
H24312
RS±46
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY (Power Adjuster Type)
3329 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
HINT:

Use the same procedures for the RH side and LH side.

The procedures listed below are for the LH side.
NOTICE:

If the wiring connector of the SRS is disconnected
and the ignition switch is in the ON or ACC position,
DTCs will be recorded.

Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
1. PRECAUTION (SEE PAGE RS±1 and RS±3)
2. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the
airbag working.
3. REMOVE SEAT TRACK COVERS
Using a screwdriver, remove the 2 seat track covers.
HINT:
Tape the screwdriver tip before use.
4. REMOVE FRONT SEAT
(a) Remove the 4 bolts.
(b) w/ Side airbag:
Disconnect the connectors.
(c) Remove the front seat.
CAUTION:
Be careful not to damage the body.
5. REMOVE HEADREST
6. REMOVE SLIDE KNOB AND RECLINING KNOB
Using a screwdriver, remove the slide knob and reclining knob.
HINT:
Tape the screwdriver tip before use.
7. REMOVE SEAT CUSHION LOWER SHIELD, SEAT
CUSHION OUTER SHIELD AND SEAT CUSHION IN-
NER SHIELD
(a) Remove the screw from the seat cushion outer shield.
(b) Perform the same procedure as for the seat cushion inner
shield.