2001 TOYOTA SEQUOIA parking brake

DIDM1±01
F13444
USA: CANADA:USA: CANADA:2WD: 4WD:
DI±910
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1104 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSIS SYSTEM
1. CHECK WARNING LIGHT
(a) Release the parking brake pedal.
(b) When the ignition switch is turned ON, check that the ABS
warning light, VSC TRAC warning light, VSC OFF (TRAC
OFF) indicator light, BRAKE warning light and SLIP indi-
cator light come on for approx. 3 seconds.
HINT:

When the parking brake is applied or the level of the brake
fluid is low, the BRAKE warning light comes on.

If the indicator check result is not normal, proceed to trou-
bleshooting for the ABS warning light circuit, VSC TRAC
warning light circuit, VSC OFF (TRAC OFF) indicator light
circuit, BRAKE warning light circuit or SLIP indicator light
circuit.
Trouble AreaSee page
ABS warning light circuitDI±1021 or
DI±1025
VSC TRAC warning light circuitDI±1027 or
DI±1031
VSC OFF (TRAC OFF) indicator light circuitDI±1048
BRAKE warning light circuitDI±1033 or
DI±1038
SLIP indicator light circuitDI±1041 or
DI±1045

The DTCs are simultaneously stored in the memory. The
DTCs can be read by connecting the SST between TC
and CG terminals of the DLC3 and observing the blinking
of the ABS and VSC warning lights, or by connecting a
hand±held tester.

This system has a sensor signal check function (TEST
MODE) (See page DI±899).
The DTC can be read by connecting the SST between ter-
minals TS and CG of the DLC3 and observing the blinking
of the ABS and VSC TRAC warning lights, or by connect-
ing a hand±held tester.

DIDM2±01
F09750
CG TcDLC3
R01346
Normal System Code
0.25 sec.
0.25 sec. 2 sec.
ON
OFF
ON
OFF0.5 sec. 0.5 sec.
Codes 11 and 21
4 sec.1.5 sec.
2.5 sec.
Code 11 Code 21
F09750
CG TcDLC3
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±911
1105 Author: Date:
2005 SEQUOIA (RM1146U)
DTC CHECK / CLEAR
USING SST (CHECK WIRE):
1. CHECK DTC
(a) Using SST, connect terminals Tc and CG of the DLC3.
SST 09843±18040
(b) Turn the ignition switch to the ON position.
(c) Read the DTC from the ABS and VSC TRAC warning
lights on the combination meter.
HINT:

If no code appears, inspect the diagnostic circuit, ABS
warning light circuit or VSC TRAC warning light circuit.
Trouble AreaSee page
Tc terminal circuitDI±1055
ABS warning light circuitDI±1021 or
DI±1025
VSC TRAC warning light circuitDI±1027 or
DI±1031

As examples, the blinking patterns for normal system
code and codes 11 and 21 are shown on the left.
(1) Codes are explained in the code table on page
DI±921.
(2) After completing the check, disconnect terminals Tc
and CG of the DLC3, and turn off the display.
If 2 or more trouble codes are identified at the same time, the
DTCs will be displayed in ascending order.
2. CHECK TRANSLATE DTC
HINT:
Once the ignition switch is turned off, all DTCs in the translate
ECU are cleared.
(a) Release the parking brake pedal.
(b) Check the brake fluid level.
(c) Using SST, connect terminals Tc and CG of the DLC3.
SST 09843±18040
(d) Read the DTC of the BRAKE warning light.
NOTICE:
When reading DTCs, be sure to be seated in the driver's
seat and depressing the brake pedal.

Trouble Code (Example Code 42, 44)
ON
OFF
0.5 sec.0.5 sec.
1.5 sec.2.5 sec.
4 sec.
Repeat
42
44
D05981
Hand±held
Tester
DLC3
DI±912
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1106 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:

If no code appears, inspect the diagnostic circuit, and
BRAKE warning light circuit.
Trouble AreaSee page
Tc terminal circuitDI±1055
BRAKE warning light circuitDI±1033 or
DI±1038

When the parking brake is applied or the level of the brake
fluid is low, the BRAKE warning light comes on.

If all sensors are normal, a normal system code is output.
(A cycle of 0.25 sec. ON and 0.25 sec. OFF is repeated.)

If 2 or more trouble codes are identified at the same time,
the codes will be displayed in ascending order.
USING HAND±HELD TESTER:
3. CHECK DTC
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) Read the DTC by following the prompts on the tester
screen.
HINT:
Refer to the hand±held tester operator's manual for further de-
tails.

DIDM5±01
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±917
1111 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
With the hand±held tester connected to the DLC3 and the ignition switch in the ON position, the ABS, TRAC
and VSC data list can be displayed. Follow the prompts on the tester screen to access the DATA LIST.
ItemMeasurement Item /
Range (Display)Normal ConditionDiagnostic Note
ABS MOT RELAYABS motor relay / ON or
OFFON : Motor relay ON
OFF : Motor relay OFF±
SOL RELAYSolenoid relay / ON or
OFFON : Solenoid relay ON
OFF : Solenoid relay OFF±
VSC / TRC OFF SWTRAC control switch / ON
or OFF
ON : TRAC control switch
ON
OFF : TRAC control switch
OFF
±
AIR BLD SUPPORTAir bleed support / ON or
OFFON : Support ON
OFF : Support OFF±
STOP LIGHT SWStop lamp switch / ON or
OFF
ON : Brake pedal de-
pressed
OFF : Brake pedal re-
leased
±
PKB SWParking brake switch / ON
or OFFON : Parking brake applied
OFF : Parking brake re-
leased
±
ABS OPERT FRABS operation (FR) / BE-
FORE or OPERATE
BEFORE : No ABS opera-
tion (FR)
OPERATE : During ABS
operation (FR)
±
ABS OPERT FLABS operation (FL) / BE-
FORE or OPERATE
BEFORE : No ABS opera-
tion (FL)
OPERATE : During ABS
operation (FL)
±
ABS OPERT RRABS operation (RR) / BE-
FORE or OPERATE
BEFORE : No ABS opera-
tion (RR)
OPERATE : During ABS
operation (RR)
±
ABS OPERT RLABS operation (RL) / BE-
FORE or OPERATE
BEFORE : No ABS opera-
tion (RL)
OPERATE : During ABS
operation (RL)
±
WHEEL SPD FR
Wheel speed sensor (FR)
reading / min.: 0 km/h (0
MPH), max.: 326 km/h
(202 MPH)
Actual wheel speedSimilar speed as indicated
on speedometer
WHEEL SPD FL
Wheel speed sensor (FL)
reading / min.: 0 km/h (0
MPH), max.: 326 km/h
(202 MPH)
Actual wheel speedSimilar speed as indicated
on speedometer
WHEEL SPD RR
Wheel speed sensor (RR)
reading / min.: 0 km/h (0
MPH), max.: 326 km/h
(202 MPH)
Actual wheel speedSimilar speed as indicated
on speedometer
WHEEL SPD RL
Wheel speed sensor (RL)
reading / min.: 0 km/h (0
MPH), max.: 326 km/h
(202 MPH)
Actual wheel speedSimilar speed as indicated
on speedometer

DI±924
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
111 8 Author: Date:
2005 SEQUOIA (RM1146U)
If the brake warning light turns on, check that the parking brake pedal is released, the brake fluid level is
normal, and no malfunction is identified in the fluid level warning switch system.
If there is a problem with VSC, the brake warning light comes on. The possible causes of a problem are as
follows:

2 or more wheel speed sensor failures

Low/high voltage

Valve failure

F19769
Translate ECU
VSC+
VSC±
IG17
T5
T511
1
T5B±RL
W
AA
J37
J38
A
J37B±R J/C
B±R B±RL
W 7
IL2
6
IL2
1
IL16
S1
2
S1
13
S1 ABS &VSC Actuator
(Skid Control ECU)
CANH
CANL
IG1
8
3C8
3A
B±R Instrument Panel J/B
4
1C
2
1C
3
1C
6
1C4
1F
11
1H
7
1J
1
1L ECU±IG
IGN1
AM1 B±R B±Y
W±R
W±LB±O
W±R
W
1 2Combination Meter
24
C6
Brake
1C5 W
8
ALTF10 Fusible
Link BlockEngine Room J/B
A W±R 1
2D1
2C
4
5
R±B R±B
B1 Brake Fluid Level
Warning SW
Y±L Y±LW±B 23
IA1
129
IA5O
A
A O
OJ43
J/C
IG Sub J/B No.4
LG±R
LG±R 4
4B4
4D
1P2 Parking
Brake SW
B
Battery 39
T5
24
T5
40
T5
4
T5 BRL
LVL2
GND
PKB2Sub J/B No.3
I18
Ignition SW
AM1 IG1
AM2 IG2 1
5 W±L
2
6
AM2
BB±R (CAN1 Circuit)
(CAN1 Circuit) DI±938
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1132 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1033
1227 Author: Date:
2005 SEQUOIA (RM1146U)
BRAKE Warning Light Circuit (Remains ON)
CIRCUIT DESCRIPTION
The BRAKE warning light comes on when the brake fluid is insufficient, the parking brake is applied or the
EBD is defective.
The skid control ECU is connected to the translate ECU via the CAN1 communication system.
DIDMN±01

F19769
Translate ECU
VSC+
VSC±
IG17
T5
T511
1
T5B±RL
W
AA
J37
J38
A
J37B±R J/C
B±R B±RL
W 7
IL2
6
IL2
1
IL16
S1
2
S1
13
S1 ABS &VSC Actuator
(Skid Control ECU)
CANH
CANL
IG1
8
3C8
3A
B±R Instrument Panel J/B
4
1C
2
1C
3
1C
6
1C4
1F
11
1H
7
1J
1
1L ECU±IG
IGN1
AM1 B±R B±Y
W±R
W±LB±O
W±R
W
1 2Combination Meter
24
C6
Brake
1C5 W
8
ALTF10 Fusible
Link BlockEngine Room J/B
A W±R 1
2D1
2C
4
5
R±B R±B
B1 Brake Fluid Level
Warning SW
Y±L Y±LW±B 23
IA1
129
IA5O
A
A O
OJ43
J/C
IG Sub J/B No.4
LG±R
LG±R 4
4B4
4D
1P2 Parking
Brake SW
B
Battery 39
T5
24
T5
40
T5
4
T5 BRL
LVL2
GND
PKB2Sub J/B No.3
I18
Ignition SW
AM1 IG1
AM2 IG2 1
5 W±L
2
6
AM2
BB±R (*) CAN1 Circuit
(*)
(*)
(*) (*) DI±1034
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1228 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM