2001 TOYOTA SEQUOIA terminal TC

DIDLU±01
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±891
1085 Author: Date:
2005 SEQUOIA (RM1146U)
ABS WITH EBD & BA & TRAC & VSC SYSTEM
PRECAUTION
NOTICE:
When disconnecting the battery terminal, initialize the following system after the terminal is recon-
nected.
System NameSee Page
Back Door Power Window Control SystemBE±77

When there is a malfunction in the contact point of the terminals or installation problems with
parts, removal and installation of the suspected problem parts may return the system to the
normal condition either completely or temporarily.

In order to determine the malfunctioning area, be sure to check the conditions at the time the
malfunction occurred, such as by DTC output and freeze frame data output, and record it before
disconnecting each connector or removing and installing parts.

Since the ABS with EBD & BA & TRAC & VSC systems may be influenced by a malfunction in
the other systems, be sure to check for DTCs in the other systems.

Be sure to remove and install the ABS & VSC actuator and each sensor with the IG switch OFF
unless specified in the inspection procedure.

When removing and installing the ABS & VSC actuator and each sensor, be sure to check that
the normal display is output in test mode inspection and in DTC output inspection after instal-
ling all the parts.

After replacing the yaw rate sensor and/or the ABS & VSC actuator assembly, make sure to per-
form yaw rate and deceleration sensors' zero point calibration
(See page DI±897).

The CAN communication system is used for data communication between the skid control ECU
(included in the actuator), the steering angle sensor, and the yaw rate sensor (the deceleration
sensor is included). If there is trouble in the CAN communication line, the DTC of the commu-
nication line is output.

If the DTC of the CAN communication line is output, repair the malfunction and troubleshoot
the ABS with EBD & BA & TRAC & VSC systems.

Since the CAN communication line has its own length and route, it can not be repaired tempo-
rarily with the bypass wire, etc.

DIDLY±01
F09750
DLC3
Ts
Tc
CG
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±897
1091 Author: Date:
2005 SEQUOIA (RM1146U)
CALIBRATION
1. ZERO POINT CALIBRATION OF MASTER CYLINDER
PRESSURE, YAW RATE AND DECELERATION SEN-
SORS
HINT:
When having replaced the master cylinder pressure, yaw rate
and deceleration sensors and/or the ECU, make sure to per-
form master cylinder pressure, yaw rate and deceleration sen-
sors' zero point calibration.
NOTICE:

While obtaining the zero point, do not vibrate the ve-
hicle by tilting, moving or shaking it and keep it in a
stationary condition. (Do not start the engine.)

Be sure to do this on a level surface (within an inclina-
tion of 1 degree).
(a) Perform master cylinder pressure, yaw rate and decelera-
tion sensors zero point calibration.
(1) Using SST, connect terminals Ts and CG of the
DLC3.
SST 09843±18040
(2) Shift the shift lever to the P position.
(3) Turn the ignition switch to the ON position.
(4) Keep the vehicle in a stationary condition on a level
surface for 4 sec. or more.
(5) Keep your foot off the brake pedal.
Do not leave 4WD vehicles in the L4 position.
(6) Press the center diff. lock (TRAC OFF) switch 3
times within 3 seconds.
(7) Check that the VSC buzzer sounds for 3 seconds.
HINT:

If the VSC buzzer does not sound, do the zero point cal-
ibration again and/or check the VSC buzzer circuit (See
page DI±1052).

If the VSC buzzer does not sound, check for yaw rate and
deceleration sensor failure (See page DI±911).
(8) Turn the ignition switch OFF.
(9) Disconnect terminals Ts and CG of the DLC3.
(b) Perform steering angle sensor zero point calibration.
This calibration is carried out automatically by following
procedures below:
(1) Make sure the system is not in sensor check mode.
(2) Calibrate the steering angle sensor by driving the
vehicle in a straight line at more than 7 MPH (12
km/h) for 5 seconds.

DIDLZ±01
F09750
DLC3Ts
CG
BR3904
0.13 sec. 0.13 sec.
ON
OFF
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±899
1093 Author: Date:
2005 SEQUOIA (RM1146U)
TEST MODE PROCEDURE
1. When not using the hand±held tester:
SENSOR CHECK (TEST MODE)
NOTICE:
When having replaced the master cylinder pressure, yaw
rate and deceleration sensors and/or the ECU, perform
zero point calibration of the master cylinder pressure, yaw
rate and deceleration sensors (See page DI±897).
HINT:
If the ignition switch is turned from the ON to the ACC or LOCK
position in test mode, test mode DTCs will be erased.
(a) Procedures for test mode:
(1) Turn the ignition switch OFF.
(2) Check that the shift lever is in the P position, and
turn the steering wheel to the neutral position.
(3) Using SST, connect terminals Ts and CG of the
DLC3.
SST 09843±18040
(4) Start the engine.
(5) Check that the ABS and VSC TRAC warning lights
blink.
HINT:
If the ABS and VSC TRAC warning lights do not blink, inspect
the ABS warning light circuit, VSC TRAC warning light circuit
and Ts terminal circuit.
(6) Keep the vehicle in a stationary condition on a level
surface for 4 sec. or more.
ABS warning light circuitDI±1021 or DI±1025
VSC TRAC warning light circuitDI±1027 or DI±1031
Ts terminal circuitDI±1057

F09750
CG TcDLC3
BR3893
Trouble Code (Example Code 72, 76)
ON
OFF
4 sec. 1.5 sec.
Repeat 2.5 sec.
0.5 sec. 0.5 sec. 0.5 sec. 0.5 sec.7726
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±901
1095 Author: Date:
2005 SEQUOIA (RM1146U)
(f) Read the DTC.
(1) Using SST, connect terminals Tc and CG of the
DLC3.
SST 09843±18040
(2) Read the number of blinks of the warning light.
HINT:

See the list of DTC (step 3).

If all sensors are normal, a normal system code is output
(A cycle of 0.25 sec. ON and 0.25 sec. OFF is repeated).

If 2 or more malfunctions are indicated at the same time,
the codes will be displayed in ascending order.
(3) After doing the check, disconnect terminals Ts and
CG, Tc and CG of the DLC3, and turn the ignition
switch OFF.
SST 09843±18040

D05981
Hand±held
Tester
DLC3
BR3904
0.13 sec. 0.13 sec.
ON
OFF
F02135
Start Position
End PositionWithin ± 5° DI±902
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1096 Author: Date:
2005 SEQUOIA (RM1146U)
2. When using the hand±held tester:
SENSOR CHECK (TEST MODE)
NOTICE:
When having replaced the master cylinder pressure, yaw
rate and deceleration sensors and/or ECU, perform zero
point calibration of the master cylinder pressure, yaw rate
and deceleration sensors (See page DI±897). Make sure
that this operation is done before performing the following.
(a) Procedures for test mode:
(1) Connect the hand±held tester to the DLC3.
(2) Check that the shift lever is in the P position, and
turn the steering wheel to the neutral position.
(3) Start the engine.
(4) Select the SIGNAL CHECK on the hand±held tes-
ter.
(5) Check that the ABS warning light and VSC TRAC
warning light blink.
HINT:
If the ABS and VSC TRAC warning lights do not blink, inspect
the ABS warning light circuit, VSC TRAC warning light circuit
and Ts terminal circuit.
(6) Keep the vehicle in a stationary condition on a level
surface for 4 sec. or more.
ABS warning light circuitDI±1021 or DI±1025
VSC TRAC warning light circuitDI±1027 or DI±1031
Ts terminal circuitDI±1057
(b) Check the yaw rate and deceleration sensor.
Shift the shift lever to the D position and drive the vehicle
at a vehicle speed of approx. 3 mph (5 km/h), turn the
steering wheel either to the left or right for 90° or more,
and turn the vehicle through 180 degrees. Check that the
VSC buzzer sounds for 3 seconds upon start off.
Stop the vehicle and shift the shift lever to the P position,
check that the VSC buzzer sounds again for 3 seconds.

DI93F±04
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±905
1099 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
If a normal code is indicated during the DTC check but the problem still occurs, check the circuits for each
problem symptom in the order given in the table below and proceed to the relevant troubleshooting page.
NOTICE:

When replacing the skid control ECU, sensor, etc., turn the ignition switch OFF.

When replacing the master cylinder pressure, yaw rate and deceleration sensors and/or the
ECU, make sure to perform master cylinder pressure, yaw rate, and deceleration sensors' zero
point calibration (See page DI±897).
SymptomSuspected AreaSee page
ABS does not operate
When the following 1. to 4. are all normal and the problem
is still occurring, replace the skid control ECU.
1. Check the DTC reconfirming that the normal code is
output.
2. IG power source circuit
3. Speed sensor circuit
4. Check the hydraulic circuit for leakage.
DI±911
DI±957
DI±925
DI±1059
ABS does not operate efficiently
When the following 1. to 4. are all normal and the problem
is still occurring, replace the skid control ECU.
1. Check the DTC reconfirming that the normal code is
output.
2. Speed sensor circuit
3. Stop light switch circuit
4. Check the hydraulic circuit for leakage.
DI±911
DI±925
DI±963
DI±1059
ABS warning light abnormal
1. ABS warning light circuit
2. Skid control ECUDI±1021 or
DI±1025
BRAKE warning light abnormal
1. BRAKE warning light circuit
2. Skid control ECU
3. Translate ECUDI±1033 or
DI±1038
DTC check cannot be done
When the following 1. to 3. are all normal and the problem
is still occurring, replace the skid control ECU.
1. ABS warning light circuit
2. Tc terminal circuit
3. VSC TRAC warning light circuit
DI±1021 or
DI±1025
DI±1055
DI±1027
DI±1031
Speed sensor signal check cannot be done1. Ts terminal circuit
2. Skid control ECUDI±1057
TRAC does not operate
Only when 1. to 4. are all normal and the problem is still
occurring, replace the skid control ECU.
1. Check the DTC, reconfirming that the normal code is
output.
2. IG power source circuit
3. Check the hydraulic circuit for leakage
4. Speed sensor circuit
DI±911
DI±957
DI±1059
DI±925
TRAC does not operate efficiently
Only when 1. to 3. are all normal and the problem is still
occurring, replace the skid control ECU.
1. Check the DTC, reconfirming that the normal code is
output.
2. Check the hydraulic circuit for leakage
3. Speed sensor circuit
DI±911
DI±1059
DI±925

DIDM0±01
F16974
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±907
1101 Author: Date:
2005 SEQUOIA (RM1146U)
TERMINALS OF ECU
1. Skid Control ECU:
Symbols (Terminal No.)Terminal Description
GND (1)Skid control ECU ground
CANL (2)Vehicle CAN communication line
VCP (3)Pedal stroke sensor (Delta S Sensor) line
CANH (6)Vehicle CAN communication line
E3 (8)Pedal stroke sensor (Delta S Sensor) ground
VYS (11)Yaw rate sensor power source
IG1 (13)IG1 power supply
PIM (14)Pedal stroke sensor (Delta S Sensor) line
D/G (15)Diagnosis tester communication line
+BM (16)Motor relay power supply
BST (17)Brake booster line
PSNC (18)Brake booster line
SS1 (19)Yaw rate sensor signal line
STS (20)Brake booster line
PSNO (21)Brake booster line
BZ (22)Buzzer output
SS2 (23)Yaw rate sensor signal line
GYAW (24)Yaw rate sensor ground
PMC2 (25)M/C pressure sensor 2 signal
VCM2 (26)M/C pressure sensor 2 power supply
E2 (27)M/C pressure sensor 2 ground
PMC (28)M/C pressure sensor 1 signal
E1 (29)M/C pressure sensor 1 ground
VCM (30)M/C pressure sensor 1 power supply
BSTP (31)Brake booster line
GND2 (32)Skid control ECU ground
FL+ (33)FL wheel speed signal line
FL± (34)FL wheel speed signal line
WA (35)ABS warning light output
RR± (36)RR wheel speed signal line
RR+ (37)RR wheel speed signal line
BSW (38)Brake inhibit signal line
STP (39)Stop light switch signal input

F19198
Skid Control ECU
(harness side connector) DI±908
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1102 Author: Date:
2005 SEQUOIA (RM1146U)Symbols (Terminal No.) Terminal Description
TS (40)Sensor check input
+BO (41)Steering angle sensor line
RL+ (42)RL wheel speed signal line
RL± (43)RL wheel speed signal line
VSCW (44)VSC OFF indicator output
FR± (45)FR wheel speed signal line
FR+ (46)FR wheel speed signal line
+BS (47)Solenoid relay power supply
2. Terminal Inspection
Disconnect the connector and measure the voltage on the wire harness side.
HINT:
Voltage can not be measured with the connector connected to the skid control ECU as the connector is water
resistance.
Symbols (Terminal No.)Wiring ColorTerminal DescriptionConditionSpecified Condition
+BM (16) ± GND1, 2 (1, 32)B±R ± W±BMotor relay power supplyIG switch ON10 to 14 V
GYAW (24) ± GND1, 2 (1, 32)G ± W±BYaw rate sensor groundAlwaysBelow 1 W
E3 (8) ± GND1, 2 (1, 32)L ± W±BM/C pressure sensor 3
groundAlwaysBelow 1 W
E2 (27) ± GND1, 2 (1, 32)W ± W±BM/C pressure sensor 2
groundAlwaysBelow 1 W
E1 (29) ± GND1, 2 (1, 32)W ± W±BM/C pressure sensor 1
groundAlwaysBelow 1 W
STP (39) ± GND1, 2 (1, 32)G±Y ± W±BStop light switch signal in-
putBrake pedal depressed8 to 14 V
STP (39) ± GND1, 2 (1, 32)G±Y ± W±BStop light switch signal in-
putBrake pedal releasedBelow 1.5 V
+BS (47) ± GND1, 2 (1, 32)B±R ± W±BSolenoid relay power sup-
plyIG switch ON10 to 14 V