2001 TOYOTA SEQUOIA service

H23934
AB0163
Wire Harness
Diameter
Stripped Wire Harness Section
H17493
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY (Power Adjuster Type)
RS±53
3336 Author: Date:
2005 SEQUOIA (RM1146U)
(d) Remove the 2 nuts and side airbag assembly from the
seatback assembly.
CAUTION:

When removing the front seat airbag assembly, work
must be started 90 seconds after the ignition switch
is turned to the ºLOCKº position and the negative (±)
terminal cable is disconnected from the battery.

When storing the front passenger airbag assembly,
keep the airbag deployment side facing upward.
(e) Using a service±purpose wire harness for the vehicle, tie
down the front passenger airbag assembly to the tire.
Wire harness: Stripped wire harness section
1.25 mm
2
or more (0.0019 in2. or more)
HINT:
To calculate the area of the stripped wire harness section:
Area = 3.14 x (Diameter)
2 divided by 4
CAUTION:
If the wire harness is too thin or an alternative object is
used to tie down the front passenger airbag assembly, it
may be snapped by the shock when the airbag is deployed.
Always use a wire harness for vehicle use with an area of
at least 1.25 mm
2
(0.0019 in.2).
(1) Install the 2 nuts to the side airbag assembly.

H23926
AB0163
Wire Harness
Diameter
Stripped Wire Harness Section
H23927
Width
Inner
Diameter RS±76
± SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
3359 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Cut off the deployment section of the curtain shield airbag
assembly.
(d) Using a service±purpose wire harness for the vehicle, tie
down the front passenger airbag assembly to the tire.
Wire harness: Stripped wire harness section
1.25 mm
2
or more (0.0019 in2. or more)
CAUTION:
If the wire harness is too thin or an alternative object is
used to tie down the curtain shield airbag assembly, it may
be snapped by the shock when the airbag is deployed. Al-
ways use a wire harness for vehicle use with an area of at
least 1.25 mm
2 (0.0019 in2.).
HINT:
To calculate the area of the stripped wire harness section:
Area = 3.14 x (Diameter)
2 divided by 4
(1) Position the curtain shield airbag assembly inside
the tire with the airbag deployment side facing in-
side.
Tire size: Must exceed the following dimensions:
Width: 185 mm (7.28 in.)
Inner diameter: 360 mm (14.17 in.)
CAUTION:

Make sure that the wire harness is tight. If there is
slack in wire harness, the curtain shield airbag as-
sembly may become loose due to the shock when the
airbag is deployed.

Always tie down the curtain shield airbag assembly
with the airbag deployment side facing inside.
NOTICE:
The tire will be marked by the airbag deployment, so use an
extra tire.

BE01E±12
± BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE±1
3405 Author: Date:
2005 SEQUOIA (RM1146U)
BODY ELECTRICAL SYSTEM
PRECAUTION
NOTICE:
When disconnecting the battery terminal, initialize the following system after the terminal is recon-
nected.
System NameSee Page
Back Door Power Window Control SystemBE±77
Take care to observe the following precautions when performing inspections or removal and replacement
of body electrical related parts.
1. LIGHTING SYSTEM
Halogen bulbs have pressurized gas inside and require special handling.
They may burst or shatter if scratched or the bulb is dropped. Hold a bulb only by its plastic or metal case.
Don't touch the glass part of a bulb with bare hands.
2. SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
The SEQUOIA is equipped with an SRS (Supplemental Restraint System) such as the driver airbag. Failure
to carry out service operations in the correct sequence could cause the SRS to unexpectedly deploy during
servicing, possibly leading to a serious accident. Before servicing (including removal and installation of parts,
inspection or replacement), be sure to read the precautions in the RS section (See page xx±xxx).
3. AUDIO SYSTEM
If the battery negative (±) terminal is disconnected, the preset AM, FM 1 and FM 2 stations stored in the
memory are erased, so be sure to make a memo of the stations and reset them after the battery terminal
is reconnected.
4. MOBILE COMMUNICATION SYSTEM
If the vehicle is equipped with a mobile communication system, refer to precautions in the IN section.

BO0HY±04
BO±4
± BODYSRS AIRBAG
3557 Author: Date:
2005 SEQUOIA (RM1146U)
SRS AIRBAG
PRECAUTION
The SEQUOIA is equipped with an SRS (Supplemental Restraint System) such as the driver airbag, front
passenger airbag and side airbag. Failure to carry out service operation in the correct sequence could cause
the SRS to unexpectedly deploy during servicing, possibly leading to a serious accident. Before servicing
(including removal or installation of parts, inspection or replacement), be sure to read the precautionary no-
tices in the RS section.

BO45L±02
H16656
Upper Window Frame Moulding
Door Glass Run
Front Door Weatherstrip
Door Glass
Rear Lower
FrameTweeter Speaker
Lower Frame
Bracket Garnish
No. 2 Glass Run
Front Lower
Frame
Door Belt Moulding
Outside Rear View Mirror No. 2 Front Door
Weatherstrip
Outside Handle
Lock Cylinder
Cable Protector
Door Lock
Door Lock Outer Cover
Window Regular
MotorWindow Regular
Sub±Assembly
Service Hole Cover
Inside Handle
Upper Armrest base panel
Power Window Switch
Speaker
Courtesy Light

Precoated part Inside Handle Bezel Door TrimInner WeatherstripDoor Hinge
Door
Check
Door Hinge
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
5.5 (56, 49 in.´lbf)
8.0 (82, 71 in.´lbf)
8.0 (82, 71 in.´lbf)
8.0 (82, 71 in.´lbf)
23 (235, 17)
23 (235, 17)
30 (306, 22)
: Specified torque


N´m (kgf´cm, ft´lbf)
± BODYFRONT DOOR
BO±9
3562 Author: Date:
2005 SEQUOIA (RM1146U)
FRONT DOOR
COMPONENTS

H16644
H16643
H16646
± BODYFRONT DOOR
BO±11
3564 Author: Date:
2005 SEQUOIA (RM1146U)
(e) Remove the inner weatherstrip from the door trim.
6. REMOVE TWEETER SPEAKER
7. REMOVE OUTSIDE REAR VIEW MIRROR
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
8. REMOVE SPEAKER
9. REMOVE INSIDE HANDLE
(a) Slide the inside handle backward to remove it.
(b) Disconnect the 2 cables from inside handle as shown in
the illustration.
10. REMOVE SERVICE HOLE COVER
(a) Using a clip remover, remove the clamp and grommets.
(b) Remove the service hole cover.
NOTICE:
Do not tear the cover.
HINT:
At the time of reassembly, please refer to the following item.
Bring out the 2 control cables and wire harness through the ser-
vice hole cover.
11. REMOVE DOOR GLASS
(a) Open the door glass until the bolts appear in the service
hole.
(b) Remove the 2 bolts.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
NOTICE:
Be careful not to drop the door glass.
(c) Pull the door glass upward to remove it.
12. REMOVE DOOR GLASS RUN
13. REMOVE UPPER WINDOW FRAME MOULDING
(a) Remove the 6 screws.
(b) Using a screwdriver or clip remover, remove the upper
window frame moulding.
HINT:
Tape the screwdriver tip before use.

H16647
4 Clips
H16648
H16649
H16650
H16651
BO±12
± BODYFRONT DOOR
3565 Author: Date:
2005 SEQUOIA (RM1146U)
14. REMOVE DOOR BELT MOULDING
(a) Apply protective tape to the outer surface as shown in the
illustration, to keep the surface from being scratched.
(b) Using a moulding remover, remove the door belt mould-
ing.
15. REMOVE FRONT LOWER FRAME
(a) Remove the 2 bolts, nut and front lower frame as shown
in the illustration.
(b) Remove the No. 2 glass run from the front lower frame.
HINT:
At the time of reassembly, please refer to the following item.
Install the No. 2 glass run to the front lower frame as shown in
the illustration.
16. REMOVE REAR LOWER FRAME
Remove the bolt, nut and rear lower frame as shown in the il-
lustration.
HINT:
Remove the rear lower frame through the service hole.
17. REMOVE WINDOW REGULATOR ASSEMBLY
(a) Disconnect the connector.
(b) Remove the 5 bolts.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
(c) Loosen the bolt, then remove the window regulator as-
sembly.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
HINT:
Remove the window regulator assembly through the service
hole.

H16651
12 3
5
64
H16652
H16653
± BODYFRONT DOOR
BO±13
3566 Author: Date:
2005 SEQUOIA (RM1146U)
(d) Remove the 3 screws and window regulator motor from
the window regulator sub±assembly.
HINT:
At the time of reassembly, please refer to the following items.

Tighten the bolts in the order shown in the illustration.

Apply MP grease to the window regulator assembly.
NOTICE:
At the time of reassembly, please refer to the following
item.
Do not apply grease to the spring of the window regulator
assembly.
18. REMOVE DOOR LOCK
(a) Disengage the 2 control cables from the clamp.
(b) Remove the clamp.
(c) Remove the screw and cable protector.
(d) Disconnect the 2 control links from the outside handle and
lock cylinder.
(e) Disconnect the connector.
(f) Remove the bolt, 3 screws and door lock.
HINT:
Remove the door lock through the service hole.
Torque:
Bolt: 5.0 N´m (51 kgf´cm, 44 in.´lbf)
Screw: 5.0 N´m (51 kgf´cm, 44 in.´lbf)
HINT:

At the time of reassembly, please refer to the following
items.

Apply adhesive to 3 screws.
Part No. 08833±00070, THREE BOND 1324 or equiva-
lent.