2001 TOYOTA SEQUOIA bulb

D12795
12
(±)(+)
12
Shift Solenoid Valve SLU:
DI±678
± DIAGNOSTICSAUTOMATIC TRANSMISSION
872 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check shift solenoid valve SLU operation.
PREPARATION:
Remove the shift solenoid valve SLU (See page AT±10).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
20C (68F)
1 ± 25.0 to 5.6 W
CHECK:
Connect the positive (+) lead with a 21 W bulb to terminal 2 and
the negative (±) lead to terminal 1 of the solenoid valve connec-
tor, then check the movement of the valve.
OK:
The solenoid makes an operating sound.
NG Replace the shift solenoid valve SLU
(See page AT±10).
OK
3 Inspect valve body (See page AT±10).
OK:
There are no foreign objects on each valve.
NG Repair or replace valve body.
OK

D12795
12
(±)(+)
12
Shift Solenoid Valve SLU:
DI±684
± DIAGNOSTICSAUTOMATIC TRANSMISSION
878 Author: Date:
2005 SEQUOIA (RM1146U)
3 Inspect shift solenoid valve SLU.
PREPARATION:
Remove the shift solenoid valve SLU (See page AT±10).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
20C (68F)
1 ± 25.0 to 5.6 W
CHECK:
Connect the positive (+) lead with a 21 W bulb to terminal 2 and
the negative (±) lead to terminal 1 of the solenoid valve connec-
tor, then check the movement of the valve.
OK:
The solenoid makes an operating sound.

NG Replace the shift solenoid valve SLU
(See page AT±10).
OK
Repair or replace the transmission wire
(See page AT±7).

H24658
Ignition SwitchON
OFF
RSCA OFF SwitchOFF
ON
RSCA OFF IndicatorON
OFFApprox.
3 secondsApprox.
2 secondsApprox.
2 seconds
Bulb Check
(SW input signal prohibited)
Approx.
0.2 secondsApprox.
0.2 seconds
H23823
DI±1142
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1336 Author: Date:
2005 SEQUOIA (RM1146U)
5. FUNCTION RSCA OFF INDICATOR
(a) The RSCA OFF indicator comes on for approximately 3 seconds after the ignition switch is turned ON,
then goes off.
(b) Approximately 3 seconds after the turning the ignition switch ON, the RSCA OFF indicator comes on
or goes off every time it detects OFF (press the switch for approximately 0.2 seconds) or ON (press
the switch for approximately 2 seconds).
HINT:
The RSCA OFF switch is reset by turning the ignition switch to the LOCK position.
As a result, the RSCA OFF switch and RSCA OFF indicator are off when the ignition switch is turned to the
ON position.
6. CHECK SRS WARNING LIGHT
(a) Turn the ignition switch to the ON position, and check that
the SRS warning light comes on for approximately 6 se-
conds (primary check).
(b) Check that the SRS warning light goes off approximately
6 seconds after the ignition switch is turned to the ON
position (constant check).
HINT:
When any of the following symptoms occur, refer to the ºProb-
lem Symptoms Tableº (see page DI±1132).

The ignition switch is turned from the LOCK to ON posi-
tion, but the SRS warning light does not come on.

The SRS warning light comes on occasionally after the
primary check period has elapsed.

The SRS warning light comes on, but DTC is not output.

DID8Q±01
DI±1608
± DIAGNOSTICSCOMBINATION METER SYSTEM
1802 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
1. METER GAUGE AND WARNING/INDICATOR
GAUGE:
ItemDetail
SpeedometerVehicle speed sensor (Direct line).
TachometerECM transmits engine speed to the meter to display.
ODO/TRIP MeterCombination meter assy.
FuelDisplays a fuel level according to a signal from the fuel sender gauge (Direct line).
Water TemperatureDisplays engine coolant temperature according to a signal from the ECM (BEAN).
Oil PressureReceives a signal from the oil pressure sender (Direct line).
Volt MeterDisplays vehicle voltage according to a voltage from the IG terminal (Direct line).
WARNING/INDICATOR:
HINT:
Combination meter bulb check is performed for 3 seconds after the ignition switch is turned ON.
ItemDetailList of indicators available for
bulb check
O/D OFFReceives a signal from the ECM (Direct line)±
TURNTurns signal switch ON (Direct line)±
BEAMReceives a signal from the body ECU (*1), Displays a signal received from the
dimmer switch (*2) (Direct line)±
SECURITYReceives a set signal from the transponder key ECU and body ECU (Direct line)±
CHARGEReceives a malfunction signal from the alternator (Direct line)
AIR BAGReceives a malfunction signal from the airbag sensor center (Direct line)
D SEAT BELTReceives the driver seat belt signal (Unfastened) from the seat belt inner front LH
(Direct line)±
DOOROpen door indicator comes on when a signal is received from the ECU (BEAN)
from each door±
A/T OIL TEMP.Warning is displayed when the oil temperature is high (Direct line)
BRAKEComes on when the parking brake switch is on or the brake fluid level warning
switch is on (Direct line)
MIL (CHECK ENGINE)Receives a malfunction signal from the ECM (Direct line)
FUEL WARNINGReceives the fuel empty signal from the fuel sender gauge (Direct line)±
ABSReceives a malfunction signal from the skid control ECU (Direct line)
WASHERWarning is displayed when the washer level is low (Direct line)±
CRUISEReceives a CRUISE on signal or malfunction signal from the ECM (Direct line)±
VSC TRACReceives a malfunction signal from the skid control ECU (Direct line)
VSC (TRAC) OFFReceives a malfunction signal from the translate ECU (Direct line)
SLIPReceives a malfunction signal from the translate ECU (Direct line)
4HIReceives a 4HI signal from the 4WD control ECU (Direct line)±
CTR DIF LOCKReceives a DIF LOCK signal from the 4WD control ECU (Direct line)±
A/T PReceives a P signal from the park/neutral position switch (Direct line)±
A/T NReceives an N signal from the park/neutral position switch (Direct line)±
A/T DReceives a D signal from the park/neutral position switch (Direct line)±
A/T 3Receives a 3 signal from the park/neutral position switch (Direct line)±
A/T 2Receives a 2 signal from the park/neutral position switch (Direct line)±
A/T LReceives an L signal from the park/neutral position switch (Direct line)±

± DIAGNOSTICSBODY CONTROL SYSTEM
DI±1687
1881 Author: Date:
2005 SEQUOIA (RM1146U)
WIRELESS DOOR LOCK CONTROL
SymptomSuspected AreaSee page
All functions of wireless door lock control system do not operate.
1. Transmitter
2. Wireless door lock receiver circuit
3. Key unlock warning switch circuit
4. Body ECUBE±99
DI±1737
DI±1715
IN±35
Lock (or unlock) function does not operate.
1. Door unlock detection switch circuit (Driver's)
(Passenger's)
(Rear Door)
(Back Door)
2. Any door ECU
3. Body ECUDI±1791
DI±1829
DI±1723
DI±1869
IN±35
IN±35
Automatic lock function operates even if any door is opened within
30 seconds after all doors are unlocked by wireless door lock
control system.1. Door courtesy light switch circuit
2. Any door ECU
3. Body ECUDI±1728
IN±35
IN±35
Wireless door lock function operates, but the buzzer does not
sound.1. Wireless door lock buzzer circuit
2. Body ECUDI±1741
IN±35
Buzzer sounds, but wireless door lock function does not operate.Body ECUIN±35
REAR WIPER AND WASHER
SymptomSuspected AreaSee page
Rear wiper does not operate.1. Rear wiper switch and motor circuit
2. Body ECUDI±1704
IN±35
Rear washer does not operate.1. Rear washer switch and motor circuit
2. Body ECUDI±1704
IN±35
LIGHT CONTROL
SymptomSuspected AreaSee page
Automatic light control does not operate.
1. Automatic light control sensor circuit
2. Light control switch circuit
3. Body ECUDI±1753
DI±1750
IN±35
Auto turn±off does not operate.
1. Door courtesy light switch circuit (Driver side)
2. Ignition switch
3. Driver door ECU
4. Body ECUDI±1728
BE±24
IN±35
IN±35
Daytime running light function does not operate.
1. Daytime running light relay circuit
2. Parking brake switch circuit
3. Body ECUDI±1712
DI±1744
IN±35
FOG LIGHT
SymptomSuspected AreaSee page
Fog lights do not come on.
1. Bulb
2. FOG fuse
3. Fog light relay and switch circuit
4. Body ECU±
BE±14
DI±1710
IN±35
OTHERS
SymptomSuspected AreaSee page
Illuminated entry function does not operate.1. Illumination circuit
2. Body ECUDI±1759
IN±35
All functions of the body control system do not operate.1. Power source circuit
2. Body ECUDI±1700
IN±35
Remote control mirror does not operate.
(w/ Driving position memory)1. Remote control mirror switch circuit
2. Driving position memory switch circuit
3. Body ECUDI±1767
DI±1772
IN±35

I07763
1
2
4
I07764
3
4
DI±2380
± DIAGNOSTICSAIR CONDITIONING SYSTEM
2574 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check power transistor.
PREPARATION:
Remove the power transistor (See page AC±84).
CHECK:
(a) Connect the positive (+) lead from the battery to terminal
1 through a 12 V ± 3.4 W test bulb and the negative (±)
lead to terminal 2.
(b) Check the test bulb lights up when another positive (+)
lead is connected to terminal 4 through a 12 V ± 3.4 W test
bulb.
OK:
Test bulb lights up.
CHECK:
Measure the resistance between terminals 3 and 4.
OK:
Resistance: 2.0 to 2.4 kW
NG Replace power transistor.
OK
5 Check harness and connector between integration control and panel and power
transistor, power transistor and body ground (See page IN±35).
NG Repair or replace harness or connector.
OK
Replace integration control and panel.

BE01E±12
± BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE±1
3405 Author: Date:
2005 SEQUOIA (RM1146U)
BODY ELECTRICAL SYSTEM
PRECAUTION
NOTICE:
When disconnecting the battery terminal, initialize the following system after the terminal is recon-
nected.
System NameSee Page
Back Door Power Window Control SystemBE±77
Take care to observe the following precautions when performing inspections or removal and replacement
of body electrical related parts.
1. LIGHTING SYSTEM
Halogen bulbs have pressurized gas inside and require special handling.
They may burst or shatter if scratched or the bulb is dropped. Hold a bulb only by its plastic or metal case.
Don't touch the glass part of a bulb with bare hands.
2. SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
The SEQUOIA is equipped with an SRS (Supplemental Restraint System) such as the driver airbag. Failure
to carry out service operations in the correct sequence could cause the SRS to unexpectedly deploy during
servicing, possibly leading to a serious accident. Before servicing (including removal and installation of parts,
inspection or replacement), be sure to read the precautions in the RS section (See page xx±xxx).
3. AUDIO SYSTEM
If the battery negative (±) terminal is disconnected, the preset AM, FM 1 and FM 2 stations stored in the
memory are erased, so be sure to make a memo of the stations and reset them after the battery terminal
is reconnected.
4. MOBILE COMMUNICATION SYSTEM
If the vehicle is equipped with a mobile communication system, refer to precautions in the IN section.

BE19B±08
BE±2
± BODY ELECTRICALTROUBLESHOOTING
3406 Author: Date:
2005 SEQUOIA (RM1146U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
POWER OUTLET
SymptomSuspect AreaSee page
Electric power source cannot be out of the power outlet.
1. PWR OUTLET Fuse
2. INVERTER Relay
3. Main Switch
4. Voltage Inverter
5. Wire HarnessBE±14
BE±20
BE±20
BE±20
±
IPO system does not operate.
Power source cannot be supplied from the power outlet socket
when the ignition switch is off.1. PWR OUTLET Fuse
2. INVERTER Relay
3. Instrument panel J/B (IPO) circuit
4. Wire HarnessBE±14
BE±20
BE±20
±
IGNITION SWITCH
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
Ignition switch is not set to each position.
1. Ignition Switch
2. Power Source Circuit (Body ECU)
3. Power Source Circuit (Driver door ECU)
4. Power Source Circuit (Passenger door ECU)BE±24
DI±1700
BE±34
DI±1849
KEY UNLOCK WARNING SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
Key unlock warning system does not operate.
(The buzzer does not sound when the driver's door is opened with
the ignition OFF and key inserted)1. Key Unlock Warning Switch
2. Driver Door Courtesy Light Switch
3. Wire Harness
4. Combination MeterBE±24
BE±40
±
±
Key unlock warning system does not operate.
(The buzzer sounds when the ignition key is ACC or ON)1. Ignition Switch
2. Wire Harness
3. Combination MeterBE±24
±
±
w/o Daytime Running Light:
HEADLIGHT AND TAILLIGHT SYSTEM
This system uses the multiplex communication system, so check diagnosis system of the multiplex commu-
nication system before you proceed with troubleshooting.
SymptomSuspect AreaSee page
Only one headlight comes on.1. Bulb
2. Wire Harness±
±
ºLO±Beamº does not light (All).
1. HEAD Relay
2. Headlight Dimmer Switch
3. Wire Harness
4. Body ECUBE±27
BE±27
±
±
ºLO±Beamº does not light (One side).
1. Bulb
2. H±LP LH Fuse
3. H±LP RH Fuse
4. Wire Harness±
BE±14
BE±14
±