2001 TOYOTA SEQUOIA O2 sensor

DI±166
± DIAGNOSTICSENGINE
360 Author: Date:
2005 SEQUOIA (RM1146U)DTC No.
DTC Detecting ConditionTrouble Area
P0171
P0174When air±fuel ratio feedback is stable after warming up the
engine, fuel trim is considered to be in error on LEAN side
(2 trip detection logic)

Air induction system

Injector blockage

Mass air flow meter

Engine coolant temperature sensor

Fuel pressure

Gas leakage in exhaust system

Open or short in heated oxygen sensor (bank 1, 2 sensor 1)
circuit

Heated oxygen sensor (bank 1, 2 sensor 1)

Heated oxygen sensor heater (bank 1, 2 sensor 1)

EFI relay

PCV piping

ECM
P0172
P0175When air±fuel ratio feedback is stable after warming up the
engine, fuel trim is considered to be in error on RICH side
(2 trip detection logic)

Injector leak, blockage

Mass air flow meter

Engine coolant temperature sensor

Ignition system

Fuel pressure

Gas leakage in exhaust system

Open or short in heated oxygen sensor (bank 1, 2 sensor 1)
circuit

Heated oxygen sensor (bank 1, 2 sensor 1)

ECM
HINT:

When DTC P0171 or P0174 is recorded, the actual air±fuel ratio is on the LEAN side. When DTC
P0172 or P0175 is recorded, the actual air±fuel ratio is on the RICH side.

If the vehicle runs out of fuel, the air±fuel ratio is LEAN and DTC P0171 or P0174 may be recorded.
The MIL then comes on.

If the total of the short±term fuel trim value and long±term fuel trim value is within
35 % (engine cool-
ant temperature is more than 75 C (167F)), the system is functioning normally.

B17394
Fuel
Compensation
Amount
1.35
1.0
0.65 +35 (%):
Lean Malfunction Threshold
±35 (%):
Rich Malfunction Threshold
P0171, P0174:
P0172, P0175:
± DIAGNOSTICSENGINE
DI±167
361 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR DESCRIPTION
Under closed±loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause
changes in the long±term fuel trim compensation value. The long±term fuel trim is adjusted when there are
persistent deviations in the short±term fuel trim values. Deviations from the ECM's estimated fuel injection
volumes also affect the average fuel trim learning value, which is a combination of the average short±term
fuel trim (fuel feedback compensation value) and the average long±term fuel trim (learning value of the air±
fuel ratio). If the average fuel trim learning value exceeds the malfunction thresholds, the ECM interprets
this a fault in the fuel system and sets a DTC.
Example:
The average fuel trim leaning value is more than +35 % or less than ±35 %, the ECM interprets this as a fuel
system malfunction.
MONITOR STRATEGY
P0171Fuel system lean (Bank 1)
RltdDTCP0172Fuel system rich (Bank 1)Related DTCsP0174Fuel system lean (Bank 2)
P0175Fuel system rich (Bank 2)
Main sensors/componentsFront oxygen sensor
Required sensors/componentsRelated sensors/componentsEngine coolant temperature sensor, Mass air flow
meter, Crankshaft position sensor
Frequency of operationContinuous
Duration10 sec.
MIL operation2 driving cycles
Sequence of operationNone

DI±168
± DIAGNOSTICSENGINE
362 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not presentSee page DI±18
Battery voltage11 V±
Fuel system statusClosed±loop
Throttle position learningCompleted
Either of the following conditions is met:Condition 1 or 2
1. Engine RPM±1,000 rpm
2. Intake air amount per revolution0.26 g/sec.±
Catalyst monitorNo executed
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Purge±cutExecuting
Either of the following conditions is metCondition 1 or 2
1. Average between short±term fuel trim and long±term fuel
trim35% or more (varies with ECT)
2. Average between short±term fuel trim and long±term fuel
trim±35% or less (varies with ECT)
WIRING DIAGRAM
Refer to DTC P2195 on page DI±383.
INSPECTION PROCEDURE
HINT:
Hand±held tester only:
Malfunctioning areas can be identified by performing the A/F CONTROL function provided in the ACTIVE
TEST. The A/F CONTROL function can help to determine whether the Air±Fuel Ratio (A/F) sensor, Heated
Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the A/F CONTROL operation using a hand±held tester.
(1) Connect a hand±held tester to the DLC3.
(2) Start the engine and turn the tester ON.
(3) Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
(4) On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE
TEST / A/F CONTROL.
(5) Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT
or LEFT button to change the fuel injection volume).
(6) Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 (AFS B2S1) and OS2 B1S2
(O2S B2S2)) displayed on the tester.
HINT:

The A/F CONTROL operation lowers the fuel injection volume by 12.5 % or increases the injection
volume by 25 %.

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

+25 %
±12.5 %
More than 3.35 V
Less than 3.0 V
1
A/F Sensor (Sensor 1)
Output Voltage
Injection volume
Output voltage
HO2 Sensor (Sensor 2)
Output VoltageMain Suspected
Trouble Areas
OK
+25 %
±12.5 %
More than 3.35 V
Less than 3.0V
Injection volume
Output voltage
+25 %
±12.5 %
More than 0.55 V
Less than 0.4V
Injection volume
Output voltage
A/F sensor+25 %
±12.5 %
More than 0.55 V
Less than 0.4V
Injection volume
Output voltage
+25 %
±12.5 %
Injection volume
Output voltage
NG
+25 %
±12.5 %
Injection volume
Output voltage
NG
+25 %
±12.5 %
Injection volume
Output voltage
NG
+25 %
±12.5 %
Injection volume
Output voltage
NG OK
OK
OK
Almost
no reaction
'
Almost
no reaction Almost
no reaction
Almost
no reaction
Case
2
3
4
A/F sensor circuit A/F sensor heater
HO2 sensor
HO2 sensor circuit HO2 sensor heater
(Air±fuel ratio extremely
lean or rich)Injector
Gas leakage from
exhaust system Fuel pressure
± DIAGNOSTICSENGINE
DI±169
363 Author: Date:
2005 SEQUOIA (RM1146U)
Standard:
Tester Display
(Sensor)Injection VolumesStatusVoltages
AFS B1S1 (AFS B2S1)
(A/F)+25 %RichLess than 3.0
AFS B1S1 (AFS B2S1)
(A/F)±12.5 %LeanMore than 3.35
O2S B1S2 (O2S B2S2)
(HO2)+25 %RichMore than 0.55
O2S B1S2 (O2S B2S2)
(HO2)±12.5 %LeanLess than 0.4
NOTICE:
The Air±Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2)
sensor has a maximum output delay of approximately 20 seconds.

Following the A/F CONTROL procedure enables technicians to check and graph the voltage outputs
of both the A/F and HO2 sensors.

To display the graph, select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD
II / ACTIVE TEST / A/F CONTROL / USER DATA / AFS B1S1 and O2S B1S2, and press the YES but-
ton and then the ENTER button followed by the F4 button.

DI±170
± DIAGNOSTICSENGINE
364 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:

Read freeze frame data using a hand±held tester. Freeze frame data record the engine condition when
malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle
was moving or stationary, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, and
other data, from the time the malfunction occurred.

A low A/F sensor voltage could be caused by a rich air±fuel mixture. Check for conditions that would
cause the engine to run rich.

A high A/F sensor voltage could be caused by a lean air±fuel mixture. Check for conditions that would
cause the engine to run lean.
1 Check any other DTCs output (in addition to DTC P0171, P0172, P0174 or P0175).
PREPARATION:
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
CHECK:
(a) Read DTCs.
Result:
Display (DTC Output)Proceed To
P0171, P0172, P0174 or P0175A
P0171, P0172, P0174 or P0175 and other DTCsB
HINT:
If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.
B Go to DTC chart (See page DI±58).
A
2 Check connection of PCV piping.
OK:
PCV hose is connected correctly and is not damaged.
NG Repair or replace PCV piping.
OK

± DIAGNOSTICSENGINE
DI±171
365 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check air induction system (See page SF±1).
CHECK:
Check the air induction system for vacuum leaks.
NG Repair or replace air induction system.
OK
4 Perform active test (A/F control).
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and turn the tester ON.
(c) Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
(d) On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST /
A/F CONTROL.
(e) Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT
button to change the fuel injection volume).
(f) Monitor the voltage outputs of A/F and HO2 sensors(AFS B1S1 (AFS B2S1) and O2S B1S2 (O2S
B2S2)) displayed on the tester.
HINT:

The A/F CONTROL operation lowers the fuel injection volume by 12.5 % or increases the injection
volume by 25 %.

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
Standard:
Tester Display
(Sensor)Injection VolumesStatusVoltages
AFS B1S1 (AFS B2S1)
(A/F)+25 %RichLess than 3.0
AFS B1S1 (AFS B2S1)
(A/F)±12.5 %LeanMore than 3.35
O2S B1S2 (O2S B2S2)
(HO2)+25 %RichMore than 0.55
O2S B1S2 (O2S B2S2)
(HO2)±12.5 %LeanLess than 0.4
Result:
Status
AFS B1S1
(AFS B2S1)Status
O2S B1S2
(O2S B2S2)A/F Condition and
A/F Sensor ConditionMisfiresSuspected Trouble AreasProceed To
Lean/RichLean/RichNormal''C
LeanLeanActual air±fuel ratio leanMay occur

PCV valve and hose

PCV hose connections

Injector blockage

Gas leakage from exhaust system

Air induction system

Fuel pressure

Mass Air Flow (MAF) meter

Engine Coolant Temperature (ECT)
sensor
A

DI±172
± DIAGNOSTICSENGINE
366 Author: Date:
2005 SEQUOIA (RM1146U)Rich
RichActual air±fuel ratio rich'

Injector leakage or blockage

Gas leakage from exhaust system

Ignition system

Fuel pressure

MAF meter

ECT sensor
A
LeanLean/RichA/F sensor malfunction'
A/F sensorB
RichLean/RichA/F sensor malfunction'
A/F sensorB
Lean: During A/F CONTROL, the A/F sensor output voltage (AFS) is consistently more than 3.35 V, and the
HO2 sensor output voltage (O2S) is consistently less than 0.4 V.
Rich: During A/F CONTROL, the AFS is consistently less than 3.0 V, and the O2S is consistently more than
0.55 V.
B Go to step 11.
C Go to step 15.
A
5 Read value of engine coolant temperature.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / COOLANT
TEMP.
CHECK:
(a) Read the COOLANT TEMP twice, when the engine is cold and also when warmed up.
Standard:
With cold engine: Same as ambient air temperature.
With warm engine: Between 75C and 95C (167F and 203F)
NG Replace engine coolant temperature sensor.
OK

B17396
HT +B
AF± AF+ Sensor 1A/F Sensor Component Side:
Front View
DI±174
± DIAGNOSTICSENGINE
368 Author: Date:
2005 SEQUOIA (RM1146U)
9 Check for spark and ignition (See page IG±1).
HINT:
If the spark plugs or ignition system malfunction, engine misfire may occur. The misfire counter can be read
with the hand±held tester. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / MIS-
FIRE / CYL#1 (to CYL#8).
NG Repair or replace ignition system.
OK
10 Check injector injection (See page SF±29).
HINT:
If the injectors malfunction, engine misfires may occur. The misfire counter can be read with the hand±held
tester. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / MISFIRE / CYL#1 (to
CYL#8).
NG Replace injector.
OK
11 Check resistance of air±fuel ratio (A/F) sensor heater.
PREPARATION:
Disconnect the air±fuel ratio (A/F) sensor connector.
CHECK:
Measure resistance between the terminals of the A/F sensor
connector.
OK:
Standard:
Tester ConnectionSpecified Condition
HT (1) ± +B (2)1.8 to 3.4 W at 20C (68F)
HT (1) ± AF± (4)10 kW or higher
NG Replace air±fuel ratio (A/F) sensor.
OK