2001 TOYOTA SEQUOIA Page 18

H01017H43107H23603
Airbag
Sensor
Assembly P/T Squib LH
C D
PL± PL+
Service Wire
P10
DI±1478
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1672 Author: Date:
2005 SEQUOIA (RM1146U)
11 Check airbag sensor assembly.
PREPARATION:
(a) From the step 6:
Turn the ignition switch to the LOCK position.
(b) From the step 6:
Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) Connect the connectors to the airbag sensor assembly.
(d) Using a service wire, connect P10±1 (PL+) and P10±2
(PL±) of connector ºCº.
NOTICE:

Twist the end of the service wire in order to insert it
into the connector.

Do not forcibly insert the twisted service wire into the
terminals of the connector when connecting.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1906, B1907 or B1908 is not output.
HINT:
Codes other than DTC B1906, B1907 and B1908 may be out-
put at this time, but they are not related to this check.
NG Replace airbag sensor assembly
(see page RS±82).
OK

H01018H23474
Airbag
Sensor
Assembly DC P/T Squib LH
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1479
1673 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check front seat outer belt LH (P/T squib LH).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) From the step 10:
Disconnect the service wire from connector ºCº.
(d) Connect the connector to the front seat outer belt LH.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1905, B1906, B1907 or B1908 is not output.
HINT:
Codes other than DTC B1905, B1906, B1907 and B1908 may
be output at this time, but they are not related to this check.
NG Replace front seat outer belt LH
(see page BO±163).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).

DI±1484
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1678 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check SRS warning light.
PREPARATION:
(a) Connect the connectors to the airbag sensor assembly.
(b) Connect the connectors to the steering wheel pad.
(c) Connect the connectors to the front passenger airbag assembly.
(d) w/ Side and curtain shield airbag:
Connect the connectors to the side airbag assembly LH and RH.
(e) w/ Side and curtain shield airbag:
Connect the connectors to the curtain shield airbag assembly LH and RH.
(f) Connect the connectors to the front seat outer belt LH and RH.
(g) Connect the negative (±) terminal cable to the battery, and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at least 6 seconds.
(b) Operate all components of the electrical system (defogger, wiper, headlight, heater blower, etc.) and
check the SRS warning light operation.
OK:
The SRS warning light does not come on.
NG Replace airbag sensor assembly
(see page RS±82).
OK
END

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1485
1679 Author: Date:
2005 SEQUOIA (RM1146U)
Trouble in Indicator of Passenger Airbag ON/OFF Indicator
CIRCUIT DESCRIPTION
The occupant classification system detects the front passenger seat condition. It then informs a passenger
of the front passenger airbag assembly condition (activated/not activated) by the passenger airbag ON/OFF
indicator.
The table below shows the normal indication condition of the passenger airbag ON/OFF indicator and the
front passenger seat condition.
Front passenger seat conditionON IndicatorOFF Indicator
Adult is seated.ONOFF
Child is seated.OFFON
VacantOFFOFF
Occupant classification system failureOFFON
INSPECTION PROCEDURE
1 Check SRS warning light.
CHECK:
Turn the ignition switch to the ON position, and check the SRS warning light condition.
HINT:
If this trouble occurs, the SRS warning light is off. If it is on, a DTC is output. Troubleshoot for the output DTC.
OK:
The SRS warning light does not come on.
NG Check DTC (see page DI±1147).
OK
DIDHT±01

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1487
1681 Author: Date:
2005 SEQUOIA (RM1146U)
3 Perform zero point calibration.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) Using the hand±held tester, perform ºZero point calibrationº (see page DI±1128).
OK:
The ºCOMPLETEDº is displayed on the tester screen.
NG Go to step 5.
OK
4 Perform sensitivity check.
Using the hand±held tester, perform ºSensitivity checkº (see page DI±1128).
OK:
Standard value: 27 to 33 kg (59.52 to 72.75 lb)
NG Go to step 5.
OK
END

DI±1488
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1682 Author: Date:
2005 SEQUOIA (RM1146U)
5 Retighten front seat assembly RH bolt (see page BO±111, BO±125).
(a) Turn the ignition switch to the LOCK position.
(b) Loosen the 4 installation bolts of the front seat assembly RH.
(c) Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
NEXT
6 Perform zero point calibration.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) Using the hand±held tester, perform ºZero point calibrationº (see page DI±1128).
OK:
The ºCOMPLETEDº is displayed on the tester screen.
NG Go to step 8.
OK
7 Perform sensitivity check.
Using the hand±held tester, perform ºSensitivity checkº (see page DI±1128).
OK:
Standard value: 27 to 33 kg (59.52 to 72.75 lb)
NG Go to step 8.
OK
END

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1489
1683 Author: Date:
2005 SEQUOIA (RM1146U)
8 Check connectors.
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
CHECK:
Check the connectors are properly connected to the occupant classification ECU and the 4 occupant classifi-
cation sensors.
OK:
The connectors are connected.
PREPARATION:
Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.
CHECK:
Check the connectors are not damaged or deformed.
OK:
The connectors are normal.
NG Repair or replace connector, then go to step 1.
OK
9 Check DTC.
PREPARATION:
(a) Connect the connectors to the occupant classification ECU and the 4 occupant classification sensors.
(b) Connect the negative (±) terminal cable to the battery.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC is not output.
NG Replace airbag sensor assembly
(see page RS±82).
OK

DI±1490
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1684 Author: Date:
2005 SEQUOIA (RM1146U)
10 Replace occupant classification ECU.
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
(c) Replace the occupant classification ECU (see page RS±111).
HINT:
Perform the inspection using parts from a normal vehicle if possible.
NEXT
11 Perform zero point calibration.
(a) Connect the negative (±) terminal cable to the battery.
(b) Connect the hand±held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Using the hand±held tester, perform ºZero point calibrationº (see page DI±1128).
OK:
The ºCOMPLETEDº is displayed on the tester screen.
NEXT
12 Perform sensitivity check.
Using the hand±held tester, perform ºSensitivity checkº (see page DI±1128).
OK:
Standard value: 27 to 33 kg (59.52 to 72.75 lb)
NEXT
END