2001 TOYOTA SEQUOIA DLC3 Ts

B17411
ECM Connector
E1AIDI
A16555
AIR INJ CHECK
AIR PUMP............................ON
EASV ............................OPEN
ASV1. .............................OPEN
ASV2...............................OPEN
A/F BANK1.......................19.05
A/F BANK2.......................19.05
PRESSURE....................17 kPa
PULSATION..............25.39 kPa
AI STATUS...........................OK
Remaining Time 05 sec.
Press [EXIT] to quit
± DIAGNOSTICSENGINE
DI±345
539 Author: Date:
2005 SEQUOIA (RM1146U) Case 3:
Diagnostic signal duty ratio from air injection driver0 %
Case 4:
Diagnostic signal duty ratio from air injection driver100 %
COMPONENT OPERATING RANGE
ParameterStandard Value
Diagnostic signal duty ratio from air injection driver
70 to 90% when secondary air injection system operating
and
0% when secondary air injection system not operating
WIRING DIAGRAM
Refer to DTC P0412 on page DI±234.
INSPECTION PROCEDURE
HINT:
The diagnostic information output from the AID can be confirmed by connecting an oscilloscope to the diag-
nostic information terminal of the AID. It narrows a trouble area search to read the waveform on the oscillo-
scope when performing the AI system intrusive operation function provided in the SYSTEM CHECK.
(a) Start the engine and warm it up.
(b) Turn the ignition switch to OFF.
(c) Connect a hand±held tester to the DLC3.
(d) Connect an oscilloscope probe to the AIDI terminal of the
ECM.
(e) Start the engine and turn the tester ON.
(f) On the tester, select the following menu items:
DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK /
AIR INJ SYSTEM.
(g) On the tester, select the following menu items:
DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK /
AIR INJ CHECK / MANUAL OPERATION / OPERATION
1 and 2.
HINT:
OPERATION 1: AP: OFF, EASV:CLOSE, ASV1:CLOSE,
ASV2:OFF
OPERATION 2: AP: ON, EASV:OPEN, ASV1:OPEN,
ASV2:OPEN

DI±348
± DIAGNOSTICSENGINE
542 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:

Using the AIR INJ CHECK operation of the SYSTEM CHECK provided in the hand±held tester func-
tion, conditions for air±fuel ratio and pressure in the secondary air injection system passage can be
checked while the secondary air injection system operating. It helps technicians to troubleshoot the
system when it malfunctioning.

Read freeze frame data using a hand±held tester. Freeze frame data record the engine condition when
malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle
was moving or stationary, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, and
other data, from the time the malfunction occurred.
1 Check any other DTCs output (In addition to air injection system DTCs).
PREPARATION:
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
CHECK:
(a) Read DTCs.
RESULT:
Display (DTC Output)Proceed To
P1613A
P1613 and other DTCsB
HINT:
If any DTCs other than P1613 are output, troubleshoot those DTCs first.
B Go to DTC chart (See page DI±58).
A

B17411
E4
AIDI
± DIAGNOSTICSENGINE
DI±349
543 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check voltage between AIDI terminal of ECM and body ground.
PREPARATION:
(a) Start the engine and warm it up.
(b) Turn the ignition switch to OFF.
(c) Connect a hand±held tester to the DLC3.
(d) Turn the ignition switch ON and turn the tester ON.
(e) Start the engine.
(f) Select the following menu items: DIAGNOSIS/EN-
HANCED OBD II/SYSTEM CHECK/AIR INJ CHECK/AU-
TOMATIC OPERATION
CHECK:
Measure the voltage between terminal E4±13 (AIDI) of the
ECM connector and body ground when the air injection system
is both ON and OFF.
RESULT:
ResultsSuspected Trouble AreasProceed To
Fixed at Low (1.6 V or less)
even when AI system ON
(Air pump ON, ASV ON)

Short between air pump or air switching valve
command signal circuit and body ground

Open in air pump command signal circuit (be-
tween ECM and AID)

Open in ASV command signal circuit (between
ECM and AID)

Open in AID ground circuit (between AID and
body ground)

Diagnostic signal circuit ground short

AID

ECM
A
Fixed at High (12 V or more)
even when AI system OFF
(Air pump OFF, ASV OFF)

Open in diagnostic signal circuit (ECM ± AID)

Short between +B circuit and diagnostic signal
circuit (ECM ± AID)

Open in AID power source circuit

AID

ECM
B
Other than above:

Fluctuating (duty signal excluding 20, 40,
80%)
AID

Open in AID ground circuit (between AID and
body ground)
C
B Go to step 5.
C Go to step 8.
A

± DIAGNOSTICSENGINE
DI±353
547 Author: Date:
2005 SEQUOIA (RM1146U)
9 Replace air injection driver.
NEXT
10 Check whether DTC output recurs.
PREPARATION:
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Clear the DTCs (see page DI±43).
(d) Start the engine.
CHECK:
(a) Perform SYSTEM CHECK to operate the air injection system.
Select the following menu items: DIAGNOSIS/ENHANCED OBD II/SYSTEM CHECK/AIR INJ
CHECK/AUTOMATIC OPERATION
(b) After operating the secondary air injection system, confirm the pending codes of the secondary air in-
jection system by selecting the following menu items: DIAGNOSIS/ENHANCED OBD II/DTC INFO/
PENDING CODES.
OK:
DTC P1613 for the secondary air injection system is not output.
NG Go to DTC chart (See page DI±58).
OK
END

DI±360
± DIAGNOSTICSENGINE
554 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check any other DTC output (in addition to DTC P2111 or P2112).
PREPARATION:
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
CHECK:
(a) Read DTCs.
Result:
Display (DTC Output)Proceed To
P2111 and/or P2112A
P2111 and/or P2112 and other DTCsB
HINT:
If any DTCs other than P2111 and/or P2112 are output, troubleshoot those DTCs first.
B Go to DTC chart (See page DI±58).
A
2 Visually check throttle valve.
PREPARATION:
Remove the intake air connector.
CHECK:
Check whether or not a foreign body is caught between the throttle valve and housing. Also, check if the valve
can open and close smoothly.
OK:
The throttle valve is not contaminated by foreign objects and can move smoothly.
NG Remove foreign body and clean throttle body.
OK

DI±368
± DIAGNOSTICSENGINE
562 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Difference between ºtarget throttle positionº and ºactual
throttle positionº0.3 V or more
COMPONENT OPERATING RANGE
Standard Value
Commanded throttle position and current throttle position are nearly the same
WIRING DIAGRAM
Refer to DTC P2102 and P2103 on page DI±354.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Are there any other codes (besides DTC P2119) being output?
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand±held tester.
RESULT:
Display (DTC Output)Proceed to
P2119A
ºP2119º and other DTCB
HINT:
If any other codes besides P2119 are output, perform the troubleshooting for those DTCs first.
B Go to relevant DTC chart (See page DI±58).
A

FI7052DepressedReleased
DI±376
± DIAGNOSTICSENGINE
570 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Connect hand±held tester, and read the voltage for accelerator pedal position
sensor data.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tes-
ter main switch ON.
(c) Enter the following menu: DIAGNOSIS / ENHANCED
OBD II / DATA LIST / ETCS / ACCEL POS #1 and ACCEL
POS #2.
CHECK:
Read the voltage for the accelerator pedal position sensor data.
OK:
Standard:
Accelerator pedalACCEL POS #1ACCEL POS #2
Released0.5 to 1.1 V1.2 to 2.0 V
Depressed2.6 to 4.5 V3.4 to 5.3 V
OK Go to step 5.
NG

± DIAGNOSTICSENGINE
DI±379
573 Author: Date:
2005 SEQUOIA (RM1146U)
5 Check whether DTC output recurs (DTC P2120, P2122, P2123, P2125, P2127,
P2128 or P2138)
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Disconnect the battery terminals or remove the EFI No. 1 fuse and ETCS fuse (Clear DTCs).
(c) Start the engine.
(d) Drive the engine at idle for 15 seconds or more.
(e) On the hand±held tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / PENDING CODES.
CHECK:
Read the DTC output.
RESULT:
Display (DTC Output)Proceed To
P2120, P2122, P2123,P2125, P2127, P2128 or P2138A
No outputB
B System is OK.
A
Replace ECM (See page SF±80).