2001 TOYOTA SEQUOIA Back Seat

BO4SC±01
± BODYFRONT SEAT (Manual Adjuster Type)
BO±125
3678 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
CAUTION:
Work must not be started until at least 90 seconds after the ignition switch is turned to the LOCK posi-
tion and the negative (±) terminal cable is disconnected from the battery.
(The SRS is equipped with a back±up power source. If work is started within 90 seconds from discon-
necting the negative (±) terminal cable of the battery, the SRS may deploy.)
NOTICE:
When removing/installing and overhauling the passenger seat, check the passenger occupant clas-
sification system and perform the zero point calibration (see page DI±1128).
HINT:
The procedures listed below are for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the airbag working.
2. REMOVE SEAT TRACK COVERS
Using a screwdriver, remove the seat track covers.
HINT:
Tape the screwdriver tip before use.
3. REMOVE FRONT SEAT
(a) Remove the 4 bolts.
(b) Disconnect the connectors.
(c) w/ Side airbag:
Disconnect the airbag connector.
(d) Remove the front seat.
NOTICE:
Be careful not to damage the vehicle body.

H24316
H24337
H24861
H24338Hog Ring
H24339Hog Ring
± BODYFRONT SEAT (Manual Adjuster Type)
BO±127
3680 Author: Date:
2005 SEQUOIA (RM1146U)
7. REMOVE ARMREST ASSEMBLY
(a) Using a screwdriver, remove the armrest cap.
(b) Remove the bolt, armrest spacer, armrest lock plate and
armrest assembly.
(c) Remove the spacer from the armrest assembly.
8. REMOVE SEATBACK COVER AND PAD
(a) Remove the hog rings from the seat frame assembly.
(b) Open the fastener.
(c) w/ Side airbag:
Remove the nut and disconnect the seatback cover
bracket from the seat frame assembly.
(d) Remove the hog rings shown in the illustration from the
seat frame assembly.
(e) Remove the hog rings shown in the illustration from the
seat frame assembly.
(f) Remove the seatback cover and pad from the seat frame
assembly.

H24319
H24335
H24336
H24395
H24342
BO±128
± BODYFRONT SEAT (Manual Adjuster Type)
3681 Author: Date:
2005 SEQUOIA (RM1146U)
9. REMOVE SEATBACK COVER
(a) Turn up the seatback cover and remove the hog rings.
(b) Remove the 2 headrest supports.
(c) Remove the seatback cover from the seatback pad.
10. REMOVE SEAT CUSHION COVER AND PAD
(a) Remove the clip.
(b) Perform the same procedure on the other side.
(c) Remove the hog rings from the seat cushion cover.
(d) Unlatch the seat cushion cover hooks, then remove the
seat cushion cover with seat cushion pad.
11. REMOVE SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat
cushion pad.
12. REMOVE RH AND LH UPPER RECLINING ADJUSTER
INSIDE COVERS
(a) Remove the screw and LH upper reclining adjuster inside
cover.
(b) Perform the same procedure on the other side.

H24336
H24335
H24319
H24339Hog Ring
H24338Hog Ring
± BODYFRONT SEAT (Manual Adjuster Type)
BO±131
3684 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Install the hog rings to the seat cushion cover.
(c) Install the clip.
(d) Perform the same procedure on the other side.
7. INSTALL SEATBACK COVER
(a) Install the seatback cover to the seatback pad.
(b) Install the 2 headrest supports.
(c) Turn up the seatback cover and install the hog rings.
8. INSTALL SEATBACK COVER AND PAD
(a) Install the seatback cover and pad to the seat frame as-
sembly.
(b) Install the hog rings to the seat frame assembly.
(c) Install the hog rings to the seat frame assembly.

H24861
H24337
H24316
H24334ClawsClip BO±132
± BODYFRONT SEAT (Manual Adjuster Type)
3685 Author: Date:
2005 SEQUOIA (RM1146U)
(d) w/ Side airbag:
Connect the seatback cover bracket to the seat frame as-
sembly with the nut.
Torque: 5.5 N´m (56 kgf´cm, 49 in.´lbf)
(e) Close the fastener.
(f) Install the hog rings to the seat frame assembly.
9. INSTALL ARMREST ASSEMBLY
(a) Install the spacer to the armrest assembly.
(b) Install the armrest assembly, armrest lock plate and arm-
rest spacer with the bolt.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
HINT:
Install the armrest lock plate as shown in the illustration.
(c) Install the armrest cap.
10. INSTALL FRONT SEAT INNER BELT.
(a) Install the front seat inner belt with the nut.
Torque: 42 N´m (430 kgf´cm, 32 ft´lbf)
(b) Connect the connectors and wire harness clamps.
11. INSTALL SEAT CUSHION INNER SHIELD
Install the seat cushion inner shield with the screw.

BO4R8±02
H24385
Headrest
Headrest
Support
Seatback CoverSeatback Pad
Seatback Frame
Seat Cushion
Cover
Seat Cushion Pad
Seat Cushion
Frame
Fold Seat
Stopper Band LH Rear Seat Lock
Seat Cushion
Under cover RH Rear Seat
Reclining Adjuster
Cushion Rear No. 1 Seat
Inner Belt
No. 1 Rear Seat
Reclining Cover
RHReclining Adjuster
Release Handle
LH Rear Seat
Reclining Adjuster
No. 1 Rear Seat
Reclining Cover LH
43 (440, 32)
Reclining
Connecting Pipe
42 (430, 31)
37 (380, 27)
37 (380, 27)
N´m (kgf´cm, ft´lbf) : Specified torque
43 (440, 32)
43 (440, 32)
43 (440, 32)
Seat Leg Cover LH Seat Leg
Cover RH
Hog Ring

Non±reusable part

Hog Ring
Fold Seat Lock Control Cable No. 1
Rear Seat Cushion
Hinge RH
Rear Seat Cushion
Hinge LH
43 (440, 32)
64 (653, 47)
RH Rear Seat Lock
± BODYREAR NO.1 SEAT (Separate Type)
BO±135
3688 Author: Date:
2005 SEQUOIA (RM1146U)
REAR NO.1 SEAT (Separate Type)
COMPONENTS
HINT:
The procedures listed below are for the RH side.

H23455
BO4R9±02
BO±136
± BODYREAR NO.1 SEAT (Separate Type)
3689 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
HINT:
The procedures listed below are for the RH side.
1. FOLD REAR SEAT RH
(a) Lower the headrest to the lowest position.
(b) Pull the seatback angle adjusting lever and fold the seat-
back down.
(c) Unlock the seat legs by pulling up one of the levers on the
seat legs, and swing the seat up and forward.
2. REMOVE REAR SEAT RH
(a) Using a screwdriver, remove the 2 seat leg covers.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 4 bolts and rear No.1 seat.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)

BO4SG±01
H17260
H23459
Hook
± BODYREAR NO.1 SEAT (Separate Type)
BO±137
3690 Author: Date:
2005 SEQUOIA (RM1146U)
DISASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:

The procedures listed below are for the RH side.

A bolt without a torque specification is shown in the stan-
dard bolt chart (see page SS±2).

Tape the screwdriver tip before using it to remove the
parts.
1. REMOVE HEADREST
2. REMOVE RECLINING ADJUSTER RELEASE HANDLE
3. REMOVE NO. 1 REAR SEAT RECLINING COVER
(a) Remove the screw and No. 1 rear seat reclining cover.
(b) Perform the same procedure on the other side.
4. REMOVE SEATBACK ASSEMBLY
(a) Tilt the seat forward.
(b) As shown in the illustration, disengage the hook and open
the seatback cover.
(c) Remove the 4 bolts and the seatback assembly.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
5. REMOVE SEATBACK COVER
(a) Remove the headrest supports.
(b) Disengage the hooks, and remove the seatback frame
from the seatback cover with pad.
(c) Remove the seatback cover from the seatback pad.
HINT:
At the time of reassembly, take as much care as possible to
minimize wrinkles when installing hog rings.