2001 TOYOTA PRIUS cruise control

ENGINE ± 1NZ-FXE ENGINE
182EG12
A ± A Cross Section Throttle Control Motor
AA
Throttle Position SensorReturn Spring
Opener Spring
182EG13
Vacuum Port55
INTAKE AND EXHAUST SYSTEM
1. Throttle Body

The adoption of the ETCS-i has realized excellent throttle control.

The ISC system and cruise control system are controlled comprehensively by the ETCS-i.

The ETCS-i, which drives the throttle valve through a DC motor that is controlled by the ECM, thus doing
away with a throttle link to connect the accelerator pedal to the throttle valve, has been adopted.

The throttle control motor is provided with a return spring that closes the throttle valve.

An opener spring is provided on the throttle position sensor side. This spring opens the throttle valve slight-
ly when the engine is stopped to prevent the throttle valve from sticking and to improve the engine's restart-
ability.

A warm coolant passage is provided below the throttle body to prevent the throttle valve from freezing
during cold temperatures.
2. Intake Manifold

Because it is not necessary to improve the in-
take air efficiency through inertial intake due to
the adoption of the Atkinson cycle, the length
of the intake pipe of the intake manifold has
been shortened, and furthermore, the intake
pipes for cylinders #1 and #2, as well as for #3
and #4, have been integrated midstream to
achieve a large-scale weight reduction.
In addition, the throttle body has been oriented
downflow in the center of the surge tank to
achieve a uniform intake air distribution.

A vacuum port has been provided for the Toyo-
ta HC adsorber and catalyst system.

ENGINE ± 1NZ-FXE ENGINE62
ENGINE CONTROL SYSTEM
1. General
The engine control system for the 1NZ-FXE engine has following system.
System
Outline
SFI
Sequential Multiport
Fuel InjectionAn L-type SFI system directly detects the intake air volume with a hot-wire
type mass air flow meter.
ESA
Electronic Spark
AdvanceIgnition timing is determined by the ECM based on signals from various
sensors. The ECM corrects ignition timing in response to engine knocking.
VVT-i
Variable Valve
Timing-intelligentControls the intake camshaft to an optimal valve timing in accordance with
the engine condition.
ETCS-i
Electronic
Throttle Control
System-intelligentOptimally controls the throttle valve opening in accordance with the ECM,
and the conditions of the engine and the vehicle, and comprehensively
controls the ISC and cruise control system.
Fuel Pump Control
Fuel pump operation is controlled by signal from the ECM.

To stop the fuel pump during operation of the SRS airbag.
Oxygen Sensor Heater
ControlMaintains the temperature of the oxygen sensors at an appropriate level to
increase accuracy of detection of the oxygen concentration in the exhaust gas.
Evaporative Emission
Control

The ECM controls the purge flow of evaporative emissions (HC) in the
charcoal canister in accordance with engine conditions.

Using 3 VSVs and a vapor pressure sensor, the ECM detects any
evaporative emission leakage occurring between the fuel tank and the
charcoal canister, and vapor reducing fuel tank through the changes in the
tank pressure. For details, see page 79.
Toyota HCAC System
The ECM controls the VSV (for Toyota HCAC System) to improve the clean
emission performance of the exhaust gas when the temperature of the TWC
is low. For details, see page 58.
Air Conditioning
Cut-Off ControlBy turning the air conditioning compressor OFF in accordance with the
engine condition, drivability is maintained.
Cooling Fan ControlRadiator cooling fan operation is controlled by signals from ECM based on
the engine coolant temperature sensor signal (THW).
HV Immobiliser
Prohibits fuel delivery, ignition, and starting the HV system if an attempt is
made to start the HV system with an invalid ignition key. For details, see page
80.
DiagnosisWhen the ECM detects a malfunction, the ECM diagnoses and memorizes
the failed section.
Fail-SafeWhen the ECM detects a malfunction, the ECM stops or controls the engine
according to the data already stored in memory.

ENGINE ± 1NZ-FXE ENGINE
182EG31
Accelerator Pedal
Position SensorThrottle Valve
Throttle Position Sensor
Throttle Control
Motor
HV
ECUECM
182EG33 182EG32
Accelerator Pedal
Position Sensor(V)
5.0
4.0
3.0
2.0
1.0
0 10 2030 405060 70 80
125Output Voltage
Accelerator Pedal Depressed AngleVPA2
VPA1 74
8. ETCS-i (Electronic Throttle Control System-intelligent)
General
The ETCS-i, which realizes excellent throttle control in all the operating ranges, has been adopted.
In the conventional throttle body, the throttle valve opening is determined invariably by the amount of
the accelerator pedal effort. In contrast, the ETCS-i used the ECM to calculate the optimal throttle valve
opening that is appropriate for the respective driving condition and uses a throttle control motor to control
the opening.
The ETCS-i controls the ISC (Idle Speed Control) system and the cruise control system.

System Diagram 
Construction
1) Accelerator Pedal Position Sensor
The accelerator pedal position sensor is mounted on the accelerator pedal. To detect the pedal opening
angle, 2 separate systems consisting of main and sub sensors are used, and 2 separate return springs are
used to improve reliability. In the detecting portions, Hall elements have been adopted. Due to the charac-
teristics of the Hall elements, different signals are output depending on whether the pedal is pressed all
the way or is released. To correct these signals, a mechanical device has been provided to detect the cor-
rect pedal opening angle. The sensors of the 2 systems output the same signals.

ENGINE ± 1NZ-FXE ENGINE
150EG39150EG40
Close
Open
VC VTA1 VTA2 E2V
5
0 Close
Output Voltage
Open VTA1 VTA2
Accelerator Pedal Depressed Angle75
2) Throttle Position Sensor
The throttle position sensor is mounted on the throttle body.
The throttle position sensor converts the amount of accelerator pedal effort into two types of electrical
signals with distinct output characteristics. The signals are then input into the ECM.
3) Throttle Control Motor
A DC motor with excellent response and minimal power consumption is used for the throttle control mo-
tor. The ECM performs the duty ratio control of the direction and the amperage of the current that flows
to the throttle control motor in order to regulate the opening angle of the throttle valve.
Operation
The ECM drives the throttle control motor by determining the target throttle valve opening in accordance
with the respective operating condition.
1) Idle Speed Control
The idle speed control is effected entirely by the ETCS-i. The following are the contents of the control:
idle-up control during cold engine operation, intake air volume control to improve the startability of the
engine, and control for when the electrical load changes such as when the air conditioning switch is turned
ON or OFF.
2) Cruise Control
Through the adoption of the ETCS-i, the vehicle speed is now controlled by the throttle control motor,
which controls the throttle valve.

THS (TOYOTA HYBRID SYSTEM)27
THS CONTROL SYSTEM
1. General
The THS control system contains the following components:
HV (Hybrid Vehicle
Control) ECU
Controls the MG1, 2 and the engine according to the demand torque,
regenerative brake control and the SOC (state of charge) of HV battery. These
factors are determined by the shift position, the degree which the accelerator
is depressed, and vehicle speed.
ECM
ControlThe HV ECU receives engine status data (rpm, torque) from the ECM and
determines the engine demand torque.
Moreover, engine stop and fuel cut signals are sent according to the driving
conditions.
In addition, the vehicle speed signal received from the combination meter is
also sent.
BRAKE
ECU
ControlThe HV ECU receives data corresponding to the total braking force needed.
The HV ECU transmits the regeneration brake demand torque valve, as well
as the regeneration brake execution torque valve.
Inverter
(for MG1,
MG2)
ControlThe HV ECU sends the signal to the power transistor in the inverter for
switching the U, V, W, phase of the MG1, 2 in order to drive the MG1 and 2.
Moreover, if an overheating, overcurrent or fault voltage signal is received
from the inverter, it is shut down.
ConverterWhen a malfunction is in the Hybrid vehicle control system, the HV ECU
sends a signal to the converter, and the converter is stopped.
MG1, MG2Detects the position of the rotor of the MG1, 2 and controls the current flowing
to the MG1, 2.
In addition, the temperature is detected and the maximum load is controlled.
Battery ECUReceives the SOC of the HV battery and the current value.
Airbag Sensor
AssemblyReceives the airbag deployment signal.
A / C ECUReceives the engine power rise demand (when air-conditioning is turned ON)
and the engine running demand for water-temperature maintenance.
Accelerator Pedal
Position SensorReceives the value corresponding to degree at which the accelerator pedal is
depressed.
Shift Position SensorReceives the shift position signal (P, R, N, D, B).
Cruise Control SwitchReceives the cruise control switch signal.
Stop Light SwitchReceives the brake signal.
Interlock Switch
(for Inverter Cover and
Service Plug)Verifies that the cover of both the inverter and the service plug have been
installed.
Circuit Breaker SensorThe high-voltage circuit is intercepted if a vehicle collision has been detected.
DiagnosisWhen the HV ECU detects a malfunction, the HV ECU diagnosis and
memorizes the values corresponding to the failure.
Fail-SafeWhen the HV ECU detects a malfunction, the HV ECU stops or controls the
actuators and ECUs according to the data already stored in memory.

THS (TOYOTA HYBRID SYSTEM)
M-UU,
VU, WU
M-SDOWN
G-UU,
VU, WU
CONT 3
SENSORS ACTUATORS
INVERTER (for MG1)
INVERTER (for MG2)
G-SDOWN
DATA LINK CONNECTOR 3 SIL, TC
IGCT RELAYAUXILIARY
BATTERY MRELBATT
BATTERY ECU
ABS ECU
VEHICLE SPEED SIGNAL
(for Hybrid Transaxle)
ACCELERATOR PEDAL
POSITION SENSOR
SHIFT POSITION SENSOR
CRUISE CONTROL SWITCH
AIRBAG SENSOR ASSEMBLY
CIRCUIT BREAKER SENSOR
INTERLOCK SWITCH
(for Inverter Cover and Service Plug)
STOP LIGHT SWITCH
A / C ECU
CONVERTER NODD
MG2
M-REF,
SIN, COS
MG1
G-REF,
SIN, COS
ECM
COMBINATION METER

Vehicle Speed Signal SPD
INVERTER
(for MG1)
INVERTER
(for MG2)
CONT 2
SYSTEM MAIN RELAY NO.1
SYSTEM MAIN RELAY NO.2
SYSTEM MAIN RELAY NO.3
G-MOTT
M-MOTT
CONT 1
HV ECU
HTD, DTH
HTB, BTH
VPA1, 2
SFT, P, R,
N, D, B
CCS
ABFCS
ACS
ILK
STP EGON
HTE, ETH
ACON
G-INVT
G-IU, IV, IW
M-SINV, FINV
M-INVT
M-IU, IV, IW
GO
SPDO
ESTP
IB
G-SINV, FINV
MG1
MG2
28
2. Construction
The configuration of the THS control system in the Prius is shown in the following chart.

BODY ELECTRICAL ± ACCESSORIES
182BE46
Cruise Control Switch Signal
Brake Cancel Signal
(Stoplight Switch)
Accelerator Opening Angle Signal
(Accelerator Pedal Position Sensor)
Shift Position Signal
(Sift Position Sensor)
Brake ECUHV ECU
Cruise Control Area

Switch Input Value

Processing

Required Vehicle Speed

Calculation
Hybrid Control Area

Required Torque

Calculation

Drive Force Distribution

between Engine and
Electric Motor
Indicator Light
ECM
Inverter189
CRUISE CONTROL SYSTEM
1. General
The Prius has adopted a cruise control system that uses the hybrid system, and it is offered as an option. This
system, which is controlled by the HV ECU that is integrated with the cruise control ECU, operates the ve-
hicle through an optimal combination of the drive forces of the electric motor and the engine in accordance
with the setting on the cruise control switch.
2. Construction
The cruise control system mainly consists of an HV ECU, cruise control switches, indicator, stoplight switch,
accelerator pedal position sensor, and the shift position sensor.
The table below shows each of the functions.
Item
Function
HV ECUControls all the functions of the cruise control system in accordance with the
signals from the sensors.
Cruise Control Main
SwitchCruise control system's ON / OFF signal requirement.
Cruise Control Switch
A three-directional switch that provides the SET / COAST, RESUME /
ACCEL, and CANCEL functions. It requires the functions and settings in
accordance with its operations.
Indicator LightIt is provided in the combination meter to display whether the system is ON
or OFF.
Stop Light SwitchDetects that the driver has stepped on the brake pedal.
Accelerator Pedal
Position SensorDetects the accelerator pedal opening angle.
Shift Position SensorDetects the shift position.

IN05Y±22
± INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMSIN±29
29 Author: Date:
2001 PRIUS (RM778U)
HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS
GENERAL INFORMATION
A large number of ECU controlled systems are used in the PRIUS. In general, the ECU controlled system
is considered to be a very intricate system requiring a high level of technical knowledge and expert skill to
troubleshoot. However, the fact is that if you proceed to inspect the circuits one by one, troubleshooting of
these systems is not complex. If you have adequate understanding of the system and a basic knowledge
of electricity, accurate diagnosis and necessary repair can be performed to locate and fix the problem. This
manual is designed through emphasis of the above standpoint to help service technicians perform accurate
and effective troubleshooting, and is compiled for the following major ECU controlled systems:
The troubleshooting procedure and how to make use of it are described on the following pages.
SystemPage
6. EngineDI±1
7. Hybrid Vehicle Control SystemDI±174
8. HV Battery Control SystemDI±312
9. Anti±Lock Brake System With EBD & RBSDI±351
10.Electric Motor Power SteeringDI±452
11. Supplemental Restraint SystemDI±495
12.Cruise Control SystemDI±640
13.Combination Meter SystemDI±662
14.Body Control SystemDI±678
15.Driver Door Control SystemDI±730
16.Multiplex Communication SystemDI±750
17.Navigation SystemDI±789
18.Air Conditioning SystemDI±864
FOR USING OBD II SCAN TOOL OR TOYOTA HAND±HELD TESTER

Before using the scan tool or tester, the scan tool's instruction book or tester's operator manual should
be read thoroughly.

If the scan tool or tester cannot communicate with ECU controlled systems when you have connected
the cable of the scan tool or tester to DLC3, turned the ignition switch ON and operated the scan tool,
there is a problem on the vehicle side or tool side.
(1) If communication is normal when the tool is connected to another vehicle, inspect the diagnosis
data link line (Bus
line) or ECU power circuit of the vehicle.
(2) If communication is still not possible when the tool is connected to another vehicle, the problem
is probably in the tool itself, so perform the Self Test procedures outline in the Tester Operator's
Manual.