2001 TOYOTA PRIUS lights

@@@@ @
@@@ @@@@ @@@@ @@@@ @@@@ @@@@
€€€€ €
€€€ €€€€ €€€€ €€€€ €€€€ €€€€
ÀÀÀÀ À
ÀÀÀ ÀÀÀÀ ÀÀÀÀ ÀÀÀÀ ÀÀÀÀ ÀÀÀÀ


W±R
7. 5A
GAUGE
1 2
34
4 8 7
2111134
1 2
3 4
1 2
B18
BL FROM POWER SOURCE SYSTEM (SEE PAGE 66)
R±L
R±L G
W±B W±B
W±B
W±BW±B
W±B
Y±GR
L 4
H17
R 6
DELAY
CIRCUIT S 6
B18
3 4
R 7
BV11
G±W G±R
G±R
G±R
G±R
G±W
G±W
(W/G)
(S/D) (S/D)
C 7
(SHIELDED) BV11I 5
L L
STOP LIGHT
15
7
TO ABS ECU
BO
50
15A
STOP
IBIB
REAR LIGHTS
WARNING LIGHT
[COMB. METER] 3C 3C
IE1 14 STOP LIGHT SW
STOP LIGHT RH
[REAR COMB. LIGHT RH]
STOP LIGHT RH
[REAR COMB. LIGHT LH]
HIGH MOUNTED
STOP LIGHT
[A]
[B]
[I]
[D]
[F]
[H]
[E]
[J]
[M]
[N][K]
[L]
[G]
[C]
LIGHT FAILURE SENSOR
2001 PRIUS (EWD414U)
B HOW TO USE THIS MANUAL
*The system shown here is an EXAMPLE ONLY. It is different to the actual
circuit shown in the SYSTEM CIRCUITS SECTION.

[O]
[P]
[Q]
[R]
[S]
[T]
[U]
[V]
2001 PRIUS (EWD414U)
B HOW TO USE THIS MANUAL
Current is applied at all times through the STOP fuse to TERMINAL 2 of the stop light SW.
When the ignition SW is turned on, current flows from the GAUGE fuse to TERMINAL 8 of the light failure sensor, and also flows
through the rear lights warning light to TERMINAL 4 of the light failure sensor.
STOP LIGHT DISCONNECTION WARNING
When the ignition SW is turned on and the brake pedal is pressed (Stop light SW on), if the stop light circuit is open, the current
flowing from TERMINAL 7 of the light failure sensor to TERMINALS 1, 2 changes, so the light failure sensor detects the
disconnection and the warning circuit of the light failure sensor is activated.
As a result, the current flows from TERMINAL 4 of the light failure sensor to TERMINAL 11 to GROUND and turns the rear lights
warning light on. By pressing the brake pedal, the current flowing to TERMINAL 8 of the light failure sensor keeps the warning
circuit on and holds the warning light on until the ignition SW is turned off.
S6 STOP LIGHT SW
2±1 : Closed with the brake pedal depressed
L4 LIGHT FAILURE SENSOR
1, 2, 7±GROUND : Approx. 12 volts with the stop light SW on
4, 8±GROUND : Approx. 12 volts with the ignition SW at ON position
11±GROUND : Always continuity
: PARTS LOCATION
CodeSee PageCodeSee PageCodeSee Page
C734L436R737
H1736R637S635
: RELAY BLOCKS
CodeSee PageRelay Blocks (Relay Block Location)
118R/B No.1 (Instrument Panel Left)

@@@ @@@ @@@
€€€ €€€ €€€
ÀÀÀ ÀÀÀ ÀÀÀ
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CodeSee PageJunction Block and Wire Harness (Connector Location)
IB20Instrument Panel Wire and Instrument Panel J/B (Lower Finish Panel)
3C22Instrument Panel Wire and J/B No.3 (Instrument Panel Left Side)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CodeSee PageJoining Wire Harness and Wire Harness (Connector Location)
IE142Floor Wire and Instrument Panel Wire (Left Kick Panel)
BV150Luggage Room Wire and Floor Wire (Luggage Compartment Left)
: GROUND POINTS
CodeSee PageGround Points Location
BL50Under the Left Quarter Pillar
BO50Back Panel Center
: SPLICE POINTS
CodeSee PageWire Harness with Splice PointsCodeSee PageWire Harness with Splice Points
I544Cowl WireB1850Luggage Room Wire
SYSTEM OUTLINE
SERVICE HINTS

2001 PRIUS (EWD414U)
E GLOSSARY OF TERMS AND SYMBOLS
BATTERY
Stores chemical energy and
converts it into electrical energy.
Provides DC current for the auto's
various electrical circuits.GROUND
The point at which wiring attaches to
the Body, thereby providing a return
path for an electrical circuit; without a
ground, current cannot flow.
CAPACITOR (Condenser)
A small holding unit for temporary
storage of electrical voltage.HEADLIGHTS
Current flow causes a headlight
filament to heat up and emit light. A
headlight may have either a single
(1) filament or a double (2) filament
1. SINGLE
FILAMENT
CIGARETTE LIGHTER
An electric resistance heating
element.2. DOUBLE
FILAMENT
CIRCUIT BREAKER
Basically a reusable fuse, a circuit
breaker will heat and open if too
much current flows through it.
Some units automatically reset when
cool, others must be manually reset.HORN
An electric device which sounds a
loud audible signal.
DIODE
A semiconductor which allows
current flow in only one direction.IGNITION COIL
Converts low±voltage DC current
into high±voltage ignition current for
firing the spark plugs.
DIODE, ZENERA diode which allows current flow in one
direction but blocks reverse flow only up
to a specific voltage. Above that potential,
it passes the excess voltage. This acts as
a simple voltage regulator.LIGHT
Current flow through a filament
causes the filament to heat up and
emit light.
PHOTODIODE
The photodiode is a semiconductor
which controls the current flow
according to the amount of light.LED (LIGHT EMITTING DIODE)
Upon current flow, these diodes emit
light without producing the heat of a
comparable light.
DISTRIBUTOR, IIA
Channels high±voltage current from
the ignition coil to the individual
spark plugs.METER, ANALOG
Current flow activates a magnetic
coil which causes a needle to move,
thereby providing a relative display
against a background calibration.
FUSEA thin metal strip which burns through
when too much current flows through it,
thereby stopping current flow and
protecting a circuit from damage.
FUSIBLE LINK
METER, DIGITAL
Current flow activates one or many
LED's, LCD's, or fluorescent
displays, which provide a relative or
digital display.
FUEL
FUSIBLE LINK
A heavy±gauge wire placed in high
amperage circuits which burns through on
overloads, thereby protecting the circuit.
The numbers indicate the crosssection
surface area of the wires.(for Medium Current Fuse)
(for High Current Fuse or
Fusible Link)MOTOR
A power unit which converts
electrical energy into mechanical
energy, especially rotary motion.
M

2001 PRIUS (EWD414U)
With the ignition SW turned on, the current flows to TERMINAL 15 of the body ECU through GAUGE fuse.
Voltage is applied at all times to TERMINAL (A) 11 of the body ECU through the TAIL relay. Coil side, and to TERMINAL (A)
2 through the HEAD relay coil side (w/o daytime running light) or through the daytime running light relay (w/ daytime running
light).
1. NORMAL LIGHTING OPERATION

With the light control SW turned to TAIL position, a signal is input into TERMINAL (A) 18 of the body ECU. Due to this signal,
the current flowing to TERMINAL (A) 11 of the body ECU flows to TERMINAL (A) 18 to TERMINAL 14 of the light control SW
to TERMINAL 16 to GROUND, and taillight relay causes taillights to turn on.

With the light control SW turned to HEAD position, a signal is input into TERMINALS (A) 17 and (A) 18 of the body ECU. Due
to this signal, the current flowing to TERMINAL (A) 2 of the body ECU flows to TERMINAL (A) 17 to TERMINAL 13 of the
light control SW to TERMINAL 16 to GROUND in the headlight circuit, and causes taillight and HEAD relay to turn the lights
on. The taillight circuit is same as above.
2. LIGHT AUTO TURN OFF OPERATION
With light on and ignition SW turned off (Input signal goes to TERMINAL 15 of the body ECU), when the driver's door is
opened (Input signal goes to TERMINAL 3 of the body ECU), the ECU operates and the current is cut off which flows from
TERMINAL (A) 11 of the body ECU to TERMINAL (A) 18 in taillight circuit and from TERMINAL (A) 2 to TERMINAL (A) 17 in
headlight circuit.
As a result, all lights are turned off automatically.
HEAD RELAY
2±1 : Closed with the light control SW at HEAD position or the dimmer SW at FLASH position
Closed with the engine running and the parking brake lever released (Parking brake SW off) [w/ daytime running light]
TAIL RELAY
3±5 : Closed with the light control SW at TAIL or HEAD position
D6 DOOR COURTESY SW LH
1±GROUND : Continuity with the front LH door open
B8 (A), B9 (B) BODY ECU
15±GROUND : Approx. 12 volts with the ignition SW at ON position
3±GROUND : Continuity with the front LH door open
(B) 9±GROUND : Always approx. 12 volts
(A) 1±GROUND : Always continuity
(A) 2±GROUND : Continuity with the light control SW at HEAD position
(A)11±GROUND : Continuity with the light control SW at TAIL or HEAD position
: PARTS LOCATION
CodeSee PageCodeSee PageCodeSee Page
B9B36F13D34J2037
C1336F1838J24A37
D336J1137J25B37
D638J12A37J2737
F11B34J13B37U137
F12C34J1737
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CodeSee PageJunction Block and Wire Harness (Connector Location)
1B27Engine Room Main Wire and Engine Room J/B (Engine Compartment Left)1F27Engine Room Main Wire and Engine Room J/B (Engine Compartment Left)
2C30Instrument Panel Wire and Instrument Panel J/B (Cowl Side Panel LH)2D30Instrument Panel Wire and Instrument Panel J/B (Cowl Side Panel LH)
2H31Engine Room Main Wire and Instrument Panel J/B (Cowl Side Panel LH)
2K31Cowl Wire and Instrument Panel J/B (Cowl Side Panel LH)
SYSTEM OUTLINE
SERVICE HINTS

2001 PRIUS (EWD414U)
WIRELESS DOOR LOCK CONTROL
The current is always sent from DOOR fuse to TERMINAL B of body ECU. At the same time, the current is always sent from
DOME fuse to TERMINAL CPUB of power window master SW, and from ECU±B fuse to wireless door lock receiver. When
ignition SW is turned on, the current is sent from GAUGE fuse to TERMINAL IG of body ECU.
1. WIRELESS DOOR LOCK OR UNLOCK NORMAL OPERATION
*Lock operation
When the LOCK SW of the transmitter is pushed, all the doors are locked.
*Unlock operation
When the UNLOCK SW of the transmitter is pushed, all the doors are unlocked.
2. AUTOMATIC LOCK OPERATION
After all the doors are unlocked by pushing the UNLOCK SW of the transmitter, unless each of the doors is opened or the
ignition key is inserted, all the doors are locked again.
3. VISUAL CONFIRMATION OF LOCK OR UNLOCK FUNCTION
When doors are locked by using the transmitter, the taillight and parking lights blink once. When doors are unlocked by using
the transmitter, the taillights and parking lights blink twice. If UNLOCK SW of the transmitter is pushed while all the doors are
locked, doors are unlocked and the room lights are turned on simultaneously.
4. WIRELESS CONTROL STOP FUNCTION
If the following situations occur, wireless door lock function does not operate.
*When each of the doors opens. (Door courtesy SW is on)
*When ignition key is inserted to ignition SW. (Unlock warning SW is on)
*When ignition SW is on.
5. REPEAT FUNCTION
If the doors are not locked after the lock signal is out put from transmitter by pushing LOCK SW, the lock signal is sent again
to lock the doors.
6. PANIC MODE FUNCTION
When the panic SW of the transmitter is pushed, the horn comes on, and the headlight and taillight flashes.
B8 (A), B9 (B) BODY ECU
15±GROUND : Approx. 12 volts with the ignition SW at ON position
8±GROUND : Always approx. 12 volts
(B) 1±GROUND : Always continuity
W5 WIRELESS DOOR LOCK CONTROL RECEIVER
5±GROUND : Always approx. 12 volts
1±GROUND : Always continuity
U1 UNLOCK WARNING SW
2±1 : Closed with the ignition key in the cylinder
: PARTS LOCATION
CodeSee PageCodeSee PageCodeSee Page
B8A36D1438J23B37
B9B36J1137J24A37
D436J12A37J25B37
D638J13B37J2737
D738J14A37J3338
D838J15B37L438
D938J1637P939
D1038J1737U137
D1138J18A37W537
D1238J19B37
D1338J22A37
SYSTEM OUTLINE
SERVICE HINTS

2001 PRIUS (EWD414U)
COMBINATION METER
MALFUNCTION
INDICATOR LAMP
ABS
SRS
TURN L
TURN R
HIGH BEAM OUTPUT CONTROLWAT ER TEMP.
(
HIGH) WAT ER TEMP.
(
LOW) CRUISE
A 17 A 18 A 19 B 5
A 16 A 10 B 4
L L L GR± R B±YL G±R
COMBINATION METERB C10 , C11A
FROM HEADLIGHTS (
*1)
FROM DAYTIME RUNNING
LIGHT RELAY (
*2) FROM TURN SI GNAL
FLASHER RELAY TO ENGINE
CONTROL MODULE
TO BRAKE ECU
TO AIRBAG SENSOR
ASSEMBLY
10A
ACC FROM POWER SOURCE SYSTEM (
SEE PAGE 50)
2D 2
GR± R
A B
B C
B B
JUNCTION
CONNECTOR J26
JUNCTION
CONNECTORB J27 , J28AGR ±R
GR± R* 1 : W/O DAYTIME RUNNING LIGHT
* 2 : W/ DAYTIME RUNNING LIGHT

NEW MODEL OUTLINE
MAIN EQUIPMENT
182MO23(For U.S.A.)
Glove box Accesory box Multi-box
Front door pocket
Seat back pocket
(Driver's and
passenger seat)
182MO24182MO09
182MO25
Small storage box
Cup holder
(for two caps use)11.839ft3 (by SAE suitcase method)
luggage space is secured.182MO26182MO27182MO28
18
Air Conditioning
An automatic air conditioning has been adopted
in consideration to ease of use.

A clean air filter which removes pollen and
dust is included as a standard fitting for puri-
fying the air inside the cab.

Two air conditioning modes, A/C for eco-
nomical air conditioning and MAX for espe-
cially strong air conditioning, are provided.
Wireless Door Lock Remote Control System
With the wireless door lock remote control system, all the doors can be locked and unlocked by signals emitted
by the transmitter.
Power Window System
A power window system which enables all windows to be raised or lowered with switches has been adopted.
An auto up/down function and jam protection function have been added to the driver's power window.
HV Immobiliser System
HV immobiliser system will not allow the HV system to be started by duplicate key is used. This system
will permit the HV system to be started only when the ID code of the transponder chip impregnated in the
key matches the ID code registered beforehand in the transponder key amplifier.
Theft Deterrent System
When an attempt is made to forcibly enter the vehicle or open the hood or trunk lid without a key, or when
the battery terminals are removed and reconnected, this system sounds the horn and flashes the headlights,
taillights and emergency flashers for about 1 minute to alert the owner. At the same time, it locks all the
doors.
Storage Space
Ample storage space with an emphasis on practicality provided throughout the Prius.
Instrument panel (passenger seat)Seat back pocketFront door pocket
Center console boxLuggage space

NEW MODEL OUTLINE
EXTERIOR
1,695 (66.7)1,465 (57.6)
mm (in.)
182IN01
182MO01
182IN02
8
Futuristic image and symmetry are reflected in the artistic
design of the new Prius.
Front Design
A short slanted hood highlights the singular front design.

The defined character lines from the front fender curving around to the rear give off a fresh appeal.

Crystal-look front combination lamps and compact grille finish off the masked look.
Rear Design
The simple rear design gives out an impression of stability.

Three-dimensional panel make-up produces a perfect balance in its feeling of presence and stability for
the rear view.

The rear combination lamps extend around to the sides, giving emphasis to the wide image.