SS0BL±01
SS±56
± SERVICE SPECIFICATIONSAUTOMATIC TRANSAXLE (A541E)
219 Author: Date:
AUTOMATIC TRANSAXLE (A541E)
SERVICE DATA
Line pressure (wheel locked)Engine idling
D position
R position
at stall (Throttle valve fully opened)
D position
R position
401 ± 461 kPa (4.1 ± 4.7 kgf/cm2, 58 ± 66 psi)
804 ± 882 kPa (8.2 ± 9.0 kgf/cm2, 117 ± 128 psi)
1,138 ± 1,236 kPa (11.6 ± 12.6 kgf/cm
2, 165 ± 179 psi)
1,716 ± 1,854 kPa (17.5 ± 18.9 kgf/cm2, 249 ± 269 psi)
Engine stall revolution2,600 ± 150 rpm
Time lag N " D position
N " R positionLess than 1.2 seconds
Less than 1.5 seconds
Engine idle speed (A/C OFF)
N position
700 ± 50 rpm
Throttle cable adjustment (Throttle valve fully opened)Between boot and face and inner cable stopper
0 ± 1 mm (0 ± 0.04 in.)
Drive plate runoutMax.
Torque converter clutch runout Max.
Torque converter clutch installation distance0.3 mm (0.0118 in.)
0.20 mm (0.0079 in.)
More than 13.7 mm (0.539 in.)
Lock±up point (Throttle valve opening 5%)
3rd gear (O/D main switch OFF) Lock±up ON
Lock±up OFF
O/D gear Lock±up ON
Lock±up OFF
60 ± 65 km/h (37 ± 40 mph)
53 ± 58 km/h (33 ± 36 mph)
60 ± 64 km/h (37 ± 40 mph)
53 ± 58 km/h (33 ± 36 mph)
Shift schedule
D position
(Throttle valve fully opened) 1 "2
2 "3
3 "O/D
O/D "3
3 "2
2 "1
(Throttle valve fully closed) 3 "O/D
O/D "3
2 position
(Throttle valve fully opened) 1 "2
3 "2
2 "1
L position
(Throttle valve fully opened) 3 "2
2 "1
60 ± 66 km/h (37 ± 41 mph)
112 ± 121 km/h (70 ± 75 mph)
174 ± 183 km/h (108 ± 114 mph)
167 ± 176 km/h (104 ± 109 mph)
104 ± 112 km/h (65 ± 70 mph)
50 ± 55 km/h (31 ± 34 mph)
35 ± 40 km/h (22 ± 25 mph)
20 ± 25 km/h (12 ± 16 mph)
60 ± 66 km/h (37 ± 41 mph)
122 ± 130 km/h (76 ± 81 mph)
50 ± 55 km/h (31 ± 34 mph)
106 ± 115 km/h (66 ± 71 mph)
54 ± 59 km/h (34 ± 37 mph)
Toyota Supports ASE CertificationPage 1 of 2
BO030-01Title:
WINDSHIELD WIPER BLADE
MAINTENANCE AND CLEANING
Models:
All Models
Technical Service
BULLETIN
December 7, 2001
The following procedures are recommended to maintain windshield wiper blade
performance.
All models.
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty±±±±
Recommendations for Windshield Wiper Maintenance, Cleaning and Use:
1. Scheduled Maintenance
Check wiper rubber blades every 4 ± 6 months or 7,500 miles for wear, cracking
and contamination.
Clean glass and rubber wiper blades if blades are not clearing glass adequately.
If this does not correct the problem, then replace the rubber elements.
2. Cleaning Procedure
Wiper Rubber: Bugs, dirt, sap and road grime on blades will cause streaking.
Clean wiper rubber of road and environmental debris using cloth or paper towel
soaked with windshield washer fluid or mild detergent.
DO NOT USE fuel, kerosene, or petroleum based products to clean rubber wiper
blades.
Windshield: Bugs, road grime, sap and car wash wax treatments decrease wiper
performance.
Rinse windshield with water and apply non±abrasive cleaner, such as Bon±Ami
(www.faultless.com), with a sponge.
NOTE:
Make sure to use plenty of water with all powder based cleaners so the glass is
not scratched.
BODY
Introduction
Applicable
Vehicles
Warranty
Information
Maintenance,
Cleaning
and Use
