2000 TOYOTA CAMRY wheel

DI±26
± DIAGNOSTICSENGINE (5S±FE)
261 Author: Date:
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
G
(E10 ± 11) ± NE(E10 ± 6)B ± W e LIdlingPulse generation
(See page DI±100)
NE
(E10 ± 12)
± NE(E10 ± 6)B ± R e LIdlingPulse generation
(See page DI±100)
FC (E7 ± 14) ± E01 (E9 ± 13)G ± R e BR IG switch ON9 ~ 14
EGR (E8 ± 15) ± E01(E9 ± 13)P ± B e BRIG switch ON0 ~ 3
ISCC (E9 ± 6)
± E01 (E9 ± 13)B ± O e BRIG switch ON
Disconnect E9 connector of ECM9 ~ 4
ISCO (E9 ±7) ± E01(E9 ± 13)W e BRIG switch ON
Disconnect E9 connector of ECMBelow 3.0
*1
OX1 (E8 ± 5) ± E1 (E9 ± 24)W e BRMaintain engine speed at 2,500 rpm for 2 min. after
warming upPulse generation
(See page DI±66)
OX2 (E8 ± 13) ± E1 (E9 ± 24)B e BRMaintain engine speed at 2,500 rpm for 2 min. after
warming upPulse generation
*1LYBRIdlingBelow 3.01
HT1 (E9 ± 1) ± E1 (E9 ± 24)L ± Y e BRIG switch ON9 ~ 14
HT2 (E9 14) E1 (E9 24)PBBRIdlingBelow 3.0HT2 (E9 ± 14) ± E1 (E9 ± 24)P ± B e BRIG switch ON9 ~ 14
KNK (E8 ± 12) ± E1 (E9 ± 24)W e BRIdlingPulse generation
(See page DI±97)
*3B ± W e BR
IG switch ON
Other shift position in P or N position9 ~ 143
NSW (E7 ± 22) ± E1 (E9 ± 24)
B W e BR
IG switch ON
Shift position in P or N position0 ~ 3.0
SPD (E7 ± 8) ± E1 (E9 ± 24)V ± W e BRIG switch ON
Rotate driving wheel slowlyPulse generation
(See page DI±145)
TE1 (E8 ± 7) ± E1 (E9 ± 24)L ± W e BRIG switch ON9 ~ 14
W (E7 4) E1 (E9 24)GRBRIdling9 ~ 14W (E7 ± 4) ± E1 (E9 ± 24)G ± R e BRIG switch ONBelow 3.0
EVP (E9 ± 3) ± E1 (E9 ± 24)V ± W e BRIG switch ON9 ~ 14
TPC (E8 ± 16) ± E1 (E9 ± 24)V e BRIG switch ON9 ~ 14
PTNK (E8 ± 8) ± E2 (E8 ± 9)P e BR
IG switch ON, Disconnect vacuum hose from vapor pressure
sensor2.9 ~ 3.7PTNK (E8 8) E2 (E8 9)P e BR
Apply vacuum (less than 66.7 kPa (500 mmHg, 19.7 in.Hg))Below 0.5
*2
AF
(E8 ± 6) ± E1 (E9 ± 24)W e BRAlways (IG switch ON)3.3 fixed*4
*2
AF (E8 ± 14) ± E1 (E9 ± 24)
O e BRAlways (IG switch ON)3.0 fixed*4
*1: Except California Specification vehicles
*2: Only for California Specification vehicles
*3: Only for A/T models
*4: The ECM terminal voltage is fixed regardless of the output voltage from the sensor.

± DIAGNOSTICSENGINE (5S±FE)
DI±27
262 Author: Date:
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
*1GBR
IdlingBelow 3.01
HTAF (E9 ± 2) ± E04 (E9 ± 15)G e BR
IG switch ON9 ~ 14
LOCK IN (E9 ± 19)
± E1 (E9 ± 24)W ± L e BRA/C compressor is operatingPulse generation
(See page DI±190)
LOCK (E7 ± 20)RWBRA/C indicator light lights upBelow 4.0LOCK (E7 20)
± E1 (E9 ± 24)R ± W e BRA/C indicator light does not lights upBelow 1.0
A/C SW (E7 ± 10)RBBRA/C switch ON9 ~ 14A/C SW (E7 10)
± E1 (E9 ± 24)R ± B e BRA/C switch OFFBelow 1.0
PRS (E7 ± 19) ± E1 (E9 ± 24)G e BRA/C pressure is normallyBelow 1.0
THR (E8 11) E2 (E8 9)LRBRIG switch ON, A/C evaporator temp. 0°C (32°F)2.2 ~ 2.6THR (E8 ± 11) ± E2 (E8 ± 9)L ± R e BRIG switch ON, A/C evaporator temp. 15°C (59°F)1.4 ~ 1.8
MGC (E7 ± 21)LYBRA/C magnetic clutch ONBelow 1.0MGC (E7 21)
± E01 (E9 ± 13)L ± Y e BRA/C magnetic clutch OFF9 ~ 14
* STP (E7 9) E1 (E9 24)GWBRIG switch ON, Brake pedal depressed7.5 ~ 14* STP (E7 ± 9) ± E1 (E9 ± 24)G ± W e BRIG switch ON, Brake pedal releasedBelow 1.5
ELS (E7 13) E1 (E9 24)BRBRDefogger switch and taillight switch ON7.5 ~ 14ELS (E7 ± 13) ± E1 (E9 ± 24)B ± R e BRDefogger switch and taillight switch OFFBelow 1.5
PSSW (E9 ± 4) BLBRIG switch ON9 ~ 14PSSW (E9 4)
± E1 (E9 ± 24)B ± L e BRAt idling, Turn steering wheel to lock positionBelow 3.0
SIL (E7 ± 6) ± E1 (E9 ± 24)W e BRDuring transmissionPulse generation
TACH (E7 ± 7) ± E1 (E9 ± 24)B ± O eBRIdlingPulse generation
KSW (E10 4) E1 (E9 24)LBBRAt the time of inserting keyBelow 1.5KSW (E10 ± 4) ± E1 (E9 ± 24)L ± B e BRIn the condition without key insertedPulse generation
RXCK (E10 ± 3)
± E1 (E9 ± 24)R ± L eBRAt the time of inserting keyPulse generation
CODE (E10 ± 8)
± E1 (E9 ± 24)G ± W eBRAt the time of inserting keyPulse generation
TXCT (E10 ± 1)
± E1 (E9 ± 24)L ± Y eBRAt the time of inserting keyPulse generation
IMLD (E10 ± 1) ± E1 (E9 ± 24)R ± Y eBRIn the condition without key insertedPulse generation
MREL (E10 ± 7)
± E1 (E9 ± 24)B ± W eBRIG switch ON9 ~ 14
IGSW (E7 ± 1) ± E1 (E9 ± 24)B ± ReBRIG switch ON9 ~ 14
*: Only for A/T models
*1: Only for California Specification vehicles

A03021
A03425
ON
SP1
(+)
SP1
(+)
w/o Immobiliser
w/ Immobiliser
AT7809
4.5 ~ 5.5 V
0
Turn the wheel
± DIAGNOSTICSENGINE (5S±FE)
DI±147
382 Author: Date:
2 Check voltage between terminal SPD of ECM connector and body ground.
PREPARATION:
(a) Remove the glove compartment (See page SF±64).
(b) Shift the shift lever to neutral.
(c) Jack up one of the front wheels.
(d) Turn the ignition switch ON.
CHECK:
Measure voltage between terminal SPD of ECM connector and
body ground when the wheel is turned slowly.
OK:
Voltage is generated intermittently.
NG Check and repair harness and connector
between combination meter and ECM.
OK
Check and replace ECM (See page IN±31).

± DIAGNOSTICSENGINE (1MZ±FE)
DI±209
444 Author: Date:
(b) TOYOTA Enhanced Signals.
TOYOTA hand±held tester displayMeasurement ItemNormal Condition*
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 1.6 ~ 2.9 ms
IAC DUTY RATIOIntake Air Control Valve Duty Ratio
Opening ratio rotary solenoid type IAC valveIdling: 27 ~ 47 %
STARTER SIGStarter SignalCranking: ON
CTP SIGClosed Throttle Position SignalThrottle Fully Closed: ON
A/C SIGA/C Switch SignalA/C ON: ON
PNP SWPark/Neutral Position Switch SignalP or N position: ON
ELCTRCL LOAD SIGElectrical Load SignalDefogger switch ON: ON
STOP LIGHT SWStop Light Switch SignalStop light switch ON: ON
PS OIL PRESS SWPower Steering Oil Pressure Switch SignalTurn steering wheel: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL#1 ~ CYL#6Abnormal revolution variation for each cylinder0%
IGNITIONTotal number of ignition for every 1,000 revolu-
tions0 ~ 3,000
EGRT GASEGR Gas Temperature Sensor Value
EGR not operating:
Temperature between intake air temp. and
engine coolant temp.
INTAKE CTRL VSVIntake Air Control Valve VSV SignalVSV operating: ON
EGR SYSTEMEGR system operating conditionIdling: OFF
A/C CUT SIGA/C Cut SignalA/C S/W OFF: ON
FUEL PUMPFuel Pump SignalIdling: ON
EVAP (PURGE) VSVEVAP VSV SignalVSV operating: Above 30%
VAPOR PRESS VSVVapor Pressure VSV SignalVSV operating: ON (TANK)
*: If no conditions are specifically stated for ºldlingº, it means the shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.

± DIAGNOSTICSENGINE (1MZ±FE)
DI±219
454 Author: Date:
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
IG switch ON4.5 ~ 5.5
IGF (E11 ± 25) ± E1 (E10 ± 17)W±R eBRIdlingPulse generation
(See page DI±351)
THG (E10 ± 13)
± E2 (E10 ± 18)G±Y eBRIG switch ON4.5 ~ 5.5
G22+ (E11 ± 10)
± NE± (E10 ± 24)B±W eLIdlingPulse generation
(See page DI±287)
NE+ (E10 ± 16)
± NE± (E10 ± 24)B±R eLIdlingPulse generation
(See page DI±287)
ELS (E7 19) E1 (E10 17)GOBRTaillight switch ON7.5 ~ 14ELS (E7 ± 19) ± E1 (E10 ± 17)G±O eBRTaillight switch OFF0 ~ 1.5
ELS2 (E7 18) E1 (E10 17)BYBRDefogger switch ON7.5 ~ 14ELS2 (E7 ± 18) ± E1 (E10 ± 17)B±Y eBRDefogger switch OFF0 ~ 1.5
EGR (E11 ± 18)
± E01 (E11 ±21)Y±G eBRIG switch ON9 ~ 14
ACIS (E11 ± 17)
± E01 (E11 ± 21)R±Y eBRIG switch ON9 ~ 14
FC (E7 3) E01 (E11 21)GRBRIG switch ON9 ~ 14FC (E7 ± 3) ± E01 (E11 ± 21)G±R eBRIdling0 ~ 3.0
EVP1 (E10 ± 7)
± E01 (E11 ± 21)LG eBRIG switch ON9 ~ 14
RSC (E11 ± 15)
± E01 (E11 ± 21)Y±B eBRIG switch ON
Disconnect E11 of ECM connector9 ~ 14
RSO (E11 ± 16)
± E01 (E11 ± 21)R±W eBRIG switch ON
Disconnect E11 of ECM connector9 ~ 14
*OXR1 (E10 ± 11)
± E1 (E10 ± 17)W eBRMaintain engine speed at 2,500 rpm for 2 min. after
warming upPulse generation
(See page DI±305)
*OXL1 (E10 ± 12)
± E1 (E10 ± 17)B eBRMaintain engine speed at 2,500 rpm for 2 min. after
warming upPulse generation
(See page DI±305)
OXS (E8 ± 8) ± E1 (E10 ± 17)B eBRMaintain engine speed at 2,500 rpm for 2 min. after
warming upPulse generation
(See page DI±305)
*HTL (E10 4) E03 (E11 30)YRBRIdling9 ~ 14*HTL (E10± 4) ± E03 (E11 ± 30)Y±R eBRIG switch ONBelow 3.0
*HTR (E10 ± 3)LBBRIdling9 ~ 14HTR (E10 3)
± E03 (E11 ± 30)L±B eBRIG switch ONBelow 3.0
HTS (E8 9) E03 (E11 30)PGBRIdling9 ~ 14HTS (E8 ± 9) ± E03 (E11 ±30)P±G eBRIG switch ONBelow 3.0
KNKR (E11 ± 27)
± E1 (E10 ± 17)W eBRIdlingPulse generation
(See page DI±283)
KNKL (E11 ± 28)±
E1 (E10 ± 17)W eBRIdlingPulse generation
(See page DI±283)
NSW (E7 ± 20)BWBR
IG switch ON
Other shift position in ºPº ,ºNº position9 ~ 14NSW (E7 20)
± E1 (E10 ± 17)B±W eBRIG switch ON
Shift position in ºPº ,ºNº position0 ~ 3.0
SPD (E8 ± 22) ± E1 (E10 ± 17)V±W eBRIG switch ON
Rotate driving wheel slowlyPulse generation
*: Only for except California specification vehicles

± DIAGNOSTICSAUTOMATIC TRANSAXLE (A140E)
DI±397
632 Author: Date:
6. MECHANICAL SYSTEM TESTS
(a) Measure the stall speed.
The object of this test is to check the overall performance of the transaxle and engine by measuring
the stall speeds in the D and R positions.
NOTICE:

Do the test at normal operating fluid temperature 50 ± 80 °C (122 ± 176 °F).

Do not continuously run this test for longer than 5 seconds.

To ensure safety, conduct this test in a wide, clear level area which provides good traction.

The stall test should always be carried out in pairs. One technician should observe the condi-
tions of wheels or wheel stoppers outside the vehicle while the other is doing the test.
(1) Chock the 4 wheels.
(2) Connect an OBD II scan tool or TOYOTA hand±held tester to DLC3.
(3) Fully apply the parking brake.
(4) Keep your left foot depressing firmly on the brake pedal.
(5) Start the engine.
(6) Shift into the D position. Press all the way down on the accelerator pedal with your right foot.
Quickly read the stall speed at this time.
Stall speed: 2,450 ± 150 rpm
(7) Do the same test in R position.
Stall speed: 2,450 ± 150 rpm
Evaluation:
ProblemPossible cause
(a) Stall speed low in D and R positions

Engine output may be insufficient

Stator one±way clutch is operating properly

HINT: If more than 600 rpm below the specified value, the torque
converter clutch could be faulty.
(b) Stall speed high in D position

Line pressure too low

Forward clutch slipping

No.2 one±way clutch not operating properly

O/D clutch slipping
(c) Stall speed high in R position

Line pressure too low

Direct clutch slipping

1st & reverse brake slipping

O/D clutch slipping
(d) Stall speed high in D and R positions

Line pressure too low

Improper fluid level

O/D one±way clutch not operating properly

± DIAGNOSTICSAUTOMATIC TRANSAXLE (A140E)
DI±399
634 Author: Date:
7. HYDRAULIC TEST
Measure the line pressure.
NOTICE:

Do the test at normal operation fluid temperature 50 ± 80 °C (122 ± 176 °F).

The line pressure test should always be carried out in pairs. One technician should observe
the conditions of wheels or wheel stoppers outside the vehicle while the other is doing the test.

Be careful to prevent SST's hose from interfering with the exhaust pipe.
(1) Warm up the ATF.
(2) Remove the test plug on the transaxle case front left side and connect SST.
(See page AX±17 for the location to connect SST)
SST 09992±00095 (09992±00231, 09992±00271)
(3) Fully apply the parking brake and chock the 4 wheels.
(4) Connect an OBD II scan tool or TOYOTA hand±held tester to DLC3.
(5) Start the engine and check idling speed.
(6) Keep your left foot pressing firmly on the brake pedal and shift into D position.
(7) Measure the line pressure when the engine is idling.
(8) Depress the accelerator pedal all the way down. Quickly read the highest line pressure when
engine speed reaches stall speed.
(9) In the same manner, do the test in R position.
Specified line pressure:
ConditionD position kPa (kgf/cm2, psi)R position kPa (kgf/cm2, psi)
Idling362 ± 422 (3.7 ± 4.3, 53 ± 61)618 ± 794 (6.3 ± 8.1, 90 ± 115)
Stall735 ± 862 (7.5 ± 8.8, 107 ± 125)1,373 ± 1,608 (14.0 ± 16.4, 199 ± 233)
If the measured pressure is not up to the specified value, recheck the throttle cable adjustment and retest.
Evaluation
ProblemPossible cause
If the measured values at all positions are higher

Throttle cable out of adjustment

Throttle valve defective

Regulator valve defective
If the measured values at all positions are lower

Throttle cable out of adjustment

Throttle valve defective

Regulator valve defective

Oil pump defective

O/D direct clutch defective
If pressure is low in the D position only
D position circuit fluid leakage

Forward clutch defective
If pressure is low in the R position only

R position circuit fluid leakage

Direct clutch defective

1st & reverse brake defective

A03021D02238
SPD
SPD
ON
(±) w/ Engine Immobiliser System
w/o Engine Immobiliser System(+)
(±)
(+)
AT7809
4.5 ~ 5.5 V
0
Turn the wheel
± DIAGNOSTICSAUTOMATIC TRANSAXLE (A140E)
DI±409
644 Author: Date:
INSPECTION PROCEDURE
1 Check operation of speedometer.
CHECK:
Drive the vehicle and check if the operation of the speedmeter in the combination meter is normal.
HINT:
The vehicle speed sensor is operating normally if the speedometer display is normal.
NG Check speedometer circuit. See combination
meter troubleshooting (See page BE±47).
OK
2 Check voltage between terminal SPD of ECM connector and body ground.
PREPARATION:
(a) Remove glove compartment (See page BO±75).
(b) Shift the shift lever to neutral.
(c) Jack up one of the front wheels.
(d) Turn ignition switch ON.
CHECK:
Measure voltage between terminal SPD of ECM connector and
body ground when the wheel is turned slowly.
OK:
Voltage is generated intermittently.
NG Check and repair harness and connector
between combination meter and ECM
(See page IN±31).
OK