2000 TOYOTA CAMRY wheel

L PART NUMBER OF CONNECTORS
Code Part Name Part NumberCodePart Name Part Number
Note : Not all of the above part numbers of the connector are established for the supply. In case of ordering
a connector or terminal with wire, please confirm in advance if there is supply for it using ªParts Catalog
Newsº (published by Parts Engineering Administration Dept.).
A 1A/C Condenser Fan Motor90980±10928
A 2A/C Magnetic Clutch and Lock Sensor90980±10942
A 3A/C Triple Pressure SW
(A/C Dual and Single Pressure SW)90980±10943
A 4ABS Actuator90980±11413
A 5ABS Actuator90980±10891
A 6ABS Actuator and ECU90080±98070
A 7ABS and Traction Actuator90980±11698
A 8ABS and Traction Actuator90980±11413
A 9ABS Speed Sensor Front LH90980±11075A10ABS Speed Sensor Front RH90980±11 075
A11Air Fuel Ratio Sensor90980±11178
A12A/C Amplifier90980±10807
A13A/C Evaporator Temp. Sensor90980±10825
A14A/C SW90980±10631
A15ABS and Traction ECU90980±11390
A16ABS and Traction ECU90980±11391
A17ABS and Traction ECU90980±11424A18ABS ECU90980±11424
A19ABS ECU90980±11390
A20Air Vent Mode Control Servo Motor90980±11165
A22Airbag Squib
(Front Passenger Airbag Assembly)90980±11884
A23Airbag Squib (Steering Wheel Pad)90980±10850
A24Ashtray Illumination81945±33010
A25ABS Speed Sensor Rear LH90980±11060A26ABS Speed Sensor Rear RH90980±11060
A27Auto Antenna Motor and Relay90980±11697
A28Air Fuel Ratio Sensor (Bank 1 Sensor 1)90980±11178A29Air Fuel Ratio Sensor (Bank 2 Sensor 1)90980±11 178
A30A/C Ambient Temp. Sensor90980±11070
A31Airbag Sensor Front LH90980±11856A32Airbag Sensor Front RH90980±11 856
A33A/C Blower Motor Linear Controller90980±11676
A34A/C Control Assembly90980±11390
A35A/C Control Assembly90980±11391
A36A/C Room Temp. Sensor90980±10825
A37A/C Solar Sensor90980±11918
A38Air Inlet Control Servo Motor90980±11165
A39Air Mix Control Servo Motor90980±11319
A40Automatic Light Control Sensor90980±11107
B 1Back±Up Light SW90980±11250
B 2Brake Fluid Level Warning SW90980±11207
B 3Blower Motor90980±10903
B 4Blower Resistor90980±10976
B 5Blower SW90980±10877
B 6Buckle SW LH90980±10825B 7Buckle SW LH90980±10825
B 8Blower Resistor (Low Speed)90980±10976
C 1Camshaft Position Sensor90980±10947C 2Crankshaft Position Sensor90980±10947
C 3Cruise Control Actuator90980±11150
C 4Cigarette Lighter90980±10760
C 5Cigarette Lighter Illumination90980±11148
C 6Clock90980±11013
C 7Clutch Start SW90980±10825
C8Combination Meter (TMC Made)90980±11114C 8Combination Meter (TMMK Made)90980±98048
C9Combination Meter (TMC Made)90980±11113C 9Combination Meter (TMMK Made)90980±98046
C10Combination Meter (TMC Made)90980±11115C10Combination Meter (TMMK Made)90980±98047
C11Combination SW90980±11594
C12Combination SW90980±11616
C13Combination SW90980±11672
C14Cruise Control Clutch SW90980±10906
C15Cruise Control ECU90980±11391
C16Condenser90980±10860
C17Center Airbag Sensor Assembly90980±11869
C18Center Airbag Sensor Assembly90980±11872
C19Center Airbag Sensor Assembly90980±11867
D1Data Link Connector 1 (1MZ±FE)90980±11195D 1Data Link Connector 1 (5S±FE)90980±11323
D 2Daytime Running Light Resistor90980±10928
D 3Diode (A/C)90980±11071
D 4Data Link Connector 290980±11417
D 5Data Link Connector 390980±11665
D6Daytime Running Light Relay (Main)90980±11058D 6Daytime Running Light Relay (Main)90980±11 058
D7Di d (C t )D7Diode (Courtesy)D 7Diode (Courtesy)90980±10962D10Diode (Dome)90980±10962
D11Diode (Idle±Up)90980±11071
D12Door Courtesy SW Front LH
D13Door Courtesy SW Front RH90980±10871D14Door Courtesy SW Rear LH90980±10871
D15Door Courtesy SW Rear RH
D16Door Key Lock and Unlock SW Front LH90980±11490D17Door Key Lock and Unlock SW Front RH90980±11490

INTRODUCTIONGENERAL REPAIR INSTRUCTIONS ±
IN±5
the specified seal lock adhesive to the bolt, nut or
threads.
(c) Precoated parts are indicated in the component il-
lustrations by the º
º symbol.
7. When necessary, use a sealer on gaskets to prevent
leaks.
8. Carefully observe all specifications for bolt tightening
torques. Always use a torque wrench.
9. Use of special service tools (SST) and special service ma-
terials (SSM) may be required, depending on the nature
of the repair. Be sure to use SST and SSM where speci-
fied and follow the proper work procedure. A list of SST
and SSM can be found at the preparation of AX section.
10. When replacing fuses, be sure the new fuse has the cor-
rect amperage rating. DO NOT exceed the rating or use
one with a lower rating.
11. To pull apart electrical connectors, pull on the connector
itself, not the wires.
12. Care must be taken when jacking up and supporting the
vehicle. Be sure to lift and support the vehicle at the prop-
er locations.
(a) If the vehicle is to be jacked up only at the front or
rear end, be sure to block the wheels at the opposite
end in order to ensure safety.
(b) After the vehicle is jacked up, be sure to support it on
stands. It is extremely dangerous to do any work on
a vehicle raised on a jack alone, even for a small job
that can be finished quickly.

Q10058
Q10059
Q00251
AX±20
± AUTOMATIC TRANSAXLE (A140E)AUTOMATIC TRANSAXLE UNIT
1913 Author: Date:
14. REMOVE EXHAUST MANIFOLD STAY
Remove the 2 bolts and exhaust manifold stay.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
15. REMOVE TRANSAXLE±TO±ENGINE BOLT
Torque: 66 N´m (670 kgf´cm, 48 ft´lbf)
16. REMOVE ENGINE HOOD
(a) Disconnect the washer pipe.
(b) Remove the 4 bolts and engine hood.
Torque: 14 N´m (145 kgf´cm, 10 ft´lbf)
17. RAISE AND SUPPORT VEHICLE SECURELY
18. REMOVE FRONT WHEELS
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
19. REMOVE ENGINE UNDER COVER AND CENTER EN-
GINE UNDER COVER
20. DISCONNECT SHIFT CONTROL CABLE
(a) Remove the nut and disconnect the shift control cable
from the park/neutral position switch.
Torque: 15 N´m (150 kgf´cm, 11 ft´lbf)
(b) Remove the clip and disconnect the shift control cable
from the bracket.
21. REMOVE DIFFERENTIAL FLUID DRAIN PLUG AND
GASKET
HINT:
At the time of installation, please refer to the following item.
Replace the used gasket with a new gasket.
22. DRAIN DIFFERENTIAL FLUID
23. REMOVE LH AND RH FENDER APRON SEALS
24. REMOVE LH AND RH DRIVE SHAFTS
(See page SA±17)

AX03I±01
AT3412
± AUTOMATIC TRANSAXLE (A140E)AUTOMATIC TRANSAXLE UNIT
AX±25
1918 Author: Date:
INSTALLATION
1. CHECK TORQUE CONVERTER CLUTCH INSTALLA-
TION
Using a scale and a straight edge, measure to the distance from
the installed surface to the transaxle housing.
Correct distance: 13.0 mm (0.512 in.) or more
2. TRANSAXLE INSTALLATION
Installation is in the reverse order of removal (See page
AX±19).
HINT:
After installation, check and inspect items as follows.

Fluid level (See page DI±389)

Front wheel alignment (See page SA±4)

Road test of the vehicle

Engine hood (See page BO±10)

INTRODUCTIONGENERAL REPAIR INSTRUCTIONS ±
IN±5
the specified seal lock adhesive to the bolt, nut or
threads.
(c) Precoated parts are indicated in the component il-
lustrations by the º
º symbol.
7. When necessary, use a sealer on gaskets to prevent
leaks.
8. Carefully observe all specifications for bolt tightening
torques. Always use a torque wrench.
9. Use of special service tools (SST) and special service ma-
terials (SSM) may be required, depending on the nature
of the repair. Be sure to use SST and SSM where speci-
fied and follow the proper work procedure. A list of SST
and SSM can be found at the preparation of AX section.
10. When replacing fuses, be sure the new fuse has the cor-
rect amperage rating. DO NOT exceed the rating or use
one with a lower rating.
11. To pull apart electrical connectors, pull on the connector
itself, not the wires.
12. Care must be taken when jacking up and supporting the
vehicle. Be sure to lift and support the vehicle at the prop-
er locations.
(a) If the vehicle is to be jacked up only at the front or
rear end, be sure to block the wheels at the opposite
end in order to ensure safety.
(b) After the vehicle is jacked up, be sure to support it on
stands. It is extremely dangerous to do any work on
a vehicle raised on a jack alone, even for a small job
that can be finished quickly.

Q06478
Q10286
Q06530
Q10038
AX±24
± AUTOMATIC TRANSAXLE (A541E)AUTOMATIC TRANSAXLE UNIT
1944 Author: Date:
12. REMOVE 2 FRONT SIDE ENGINE MOUNTING BOLTS
Torque:
TMC Made: 80 N´m (820 kgf´cm, 59 ft´lbf)
TMMK Made:
Green color bolt: 66 N´m (670 kgf´cm, 48 ft´lbf)
Silver color bolt: 44 N´m (440 kgf´cm, 32 ft´lbf)
13. REMOVE STARTER AND A/T SHIFT CABLE CLAMP
(a) Disconnect the connector and remove the nut.
(b) Remove the 2 bolts, starter and A/T shift cable clamp.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
14. REMOVE EXHAUST MANIFOLD BRACKET MOUNT-
ING BOLT
Torque:
Except California: 20 N´m (200 kgf´cm, 15 ft´lbf)
California: 34 N´m (350 kgf´cm, 25 ft´lbf)
15. REMOVE 5 TRANSAXLE±TO±ENGINE BOLTS AND
DISCONNECT GROUND TERMINAL
Torque: 66 N´m (670 kgf´cm, 48 ft´lbf)
16. REMOVE ENGINE HOOD
(a) Disconnect the washer pipe.
(b) Remove the 4 bolts and engine hood.
Torque: 26 N´m (265 kgf´cm, 19 ft´lbf)
17. RAISE AND SUPPORT VEHICLE SECURELY
18. REMOVE FRONT WHEELS
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
19. REMOVE DIFFERENTIAL FLUID DRAIN PLUG AND
GASKET
HINT:
At the time of installation, please refer to the following item.
Replace the used gasket with a new gasket.
20. DRAIN DIFFERENTIAL FLUID
21. REMOVE LH AND RH ENGINE SIDE COVERS
22. REMOVE LH AND RH FRONT DRIVE SHAFTS
(See page SA±25)

AX03Z±01
AT3412
± AUTOMATIC TRANSAXLE (A541E)AUTOMATIC TRANSAXLE UNIT
AX±29
1949 Author: Date:
INSTALLATION
1. CHECK TORQUE CONVERTER CLUTCH INSTALLA-
TION
Using a scale and a straight edge, measure from the installed
surface to the transaxle housing.
Correct distance: 13.7 mm (0.539 in.) or more
2. TRANSAXLE INSTALLATION
Installation is in the reverse order of removal.
(See page AX±23)
HINT:
After installation, check and inspect items as follows.

Fluid level. (See page DI±438)

Front wheel alignment. (See page SA±4)

Do the road test. (See page DI±438)

Hood. (See page BO±10)

BO0MB±01
N20950
Instrument Panel ReinforcementNN
DD
No.2 Instrumental Panel Bracket
No.1 Instrumental Panel Bracket
No.2 Instrumental Panel Brace
QQH N
N
N
N
GG
NG
NOB
NN
Instrument Panel Brace Mount
No.1 Instrument
Panel BraceFront Pillar Garnish
Front Pillar
GarnishFront
Passenger
Airbag
Assembly
20 (200, 14)
No.2 Side Defroster Nozzle
Cowl Side Trim
Front Door Openin
g
Cover
Instrument Panel
C
Remote Control
Mirror Hole Base
Upper Column
CoverHazard Warning
Switch
Lower Finish
PlateGlove Compartment
Door Finish PlateFront Door
Inside Scuff Plate
FFF
FJ
Glove
Compartment
No.2 Lower
Panel A
A
Cluster Finish
Panel
Lower Column
Cover
Front Door
Opening
Cover
Cowl Side
TrimD
DD
D
D
F
AA
Lower Panel
InsertCoin
BoxCombination SwitchCombination
MeterRadio Assembly
Center Cluster
Finish Panel
A/C
Control Assembly
35 (360, 26)
Steering
Wheel
Pad Steering Wheel No.1 Lower
Panel
Front Door
Inside Scuff PlateFront Console
Box
Center Console
Upper PanelF
F
B
B
Rear Console
Box
N´m (kgf´cm, ft´lbf) : Specified torque BO±72
± BODYINSTRUMENT PANEL
2420 Author: Date:
INSTRUMENT PANEL
COMPONENTS