2000 TOYOTA CAMRY torque

CAMRY - MAJOR TECHNICAL SPECIFICATIONS
1st Gear km / h (mph) Angle of Approach degrees
Angle of Departure degrees
ItemArea
Body Type
Vehicle Grade
Model Code
OverallLength mm (in.)
Width mm (in.)
Height*
1mm (in.)
Wheel Base mm (in.)
TreadFront mm (in.)
Rear mm (in.)
Effective Head RoomFront mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.) Effective Leg Room
Shoulder Room
Overhang
Min. Running Ground Clearance mm (in.)
Curb Weight
Gross Vehicle WeightFront kg (lb)
Rear kg (lb)
Total kg (lb)
Front kg (lb)
Rear kg (lb)
Total kg (lb)
Fuel Tank Capacity (US.gal., lmp.gal)
Luggage Compartment Capacity m
3 (cu.ft.)
Max. Speed km / h (mph)
Max. Cruising Speed km / h (mph)
Max. Permissible
Speed
Turning Diameter
(Outside Front)2nd Gear km / h (mph)
3rd Gear km / h (mph)
4th Gear km / h (mph)
Wall to Wall m (ft.)
Curb to Curb m (ft.)
Engine Type
Valve Mechanism
Bore x Stroke mm (in.)
Displacement cm
3 (cu.in.)
Compression Ratio
Carburetor Type
Research Octane No. RON
Max. Output (SAE-NET) kW / rpm (HP@rpm)
Max. Torque (SAE-NET) N
.m / rpm (lb-ft@rpm)
Battery Capacity (5HR) Voltage & Amp. hr.
Generator Output Watts
Starter Output kW
Clutch Type
Transaxle Type
Transmission Gear
Ratio
Differential Gear Ratio (Final)
Brake Type
Parking Brake Type
Brake Booster Type and Size in.
Proportioning Valve Type
Suspension Type
Stabilizer Bar
Steering Gear Type
Steering Gear Ratio (Overall)
Power Steering TypeIn First
In Second
In Third
In Fourth
In Fifth
In Reverse
Front
Rear
Front
Rear
Front
Rear
5
10
15
20
25
30
35
40
45
50
55
60
65
70
Major Dimensions & Vehicle Weights Performance Engine Engine
Chassis
Electrical
U.S.A.
4-Door Sedan
CEXLE
0 to 100 mph sec.
0 to 400 m sec. Acceleration
Counter Gear RatioLE
4
MAJOR TECHNICAL SPECIFICATIONS
SXV20L-CEMDKA SXV20L-CEPDKA SXV20L-A(C)EPNKA SXV20L-A(C)EPGKA
4790 (188.6)



1780 (70.1)

1785 (70.3)
1415 (55.7)



2670 (105.1)



1545 (60.8)



1520 (59.8)



980 (38.6), 950 (37.4)*
2



940 (37.0), 914 (36.0)*2



1102 (43.4)



901 (35.5)



1427 (56.2)



1425 (56.1)



975 (38.4)



1145 (45.1)



130 (5.1)



16




16




810 (1786) 835 (1841) 865 (1907)*
3, 875 (1929)*4870 (1918)*3, 875 (1929)*4
550 (1213) 545 (1202) 540 (1191)*3, 550 (1213)*4545 (1202)*3, 555 (1224)*4
1360 (2999) 1380 (3043) 1405 (3097)*3, 1425 (3142)*41415 (3120)*3, 1430 (3153)*4
965 (2130)
995 (2195)

845 (1860)
900 (1985)

1810 (3990)
1895 (4180)

70 (18.5, 15.4)



0.399 (14.1)



180 (112)



ÐÐÐÐ
ÐÐÐÐ
ÐÐÐÐ
52 (32) 69 (43)


95 (58) 125 (78)


147 (91) Ð Ð Ð
ÐÐÐÐ
11.5 (37.7)



11.0 (36.1)



5S-FE



16-Valve, DOHC



87.0 x 91.0 (3.43 x 3.58)



2164 (132.0)



9.5 : 1



SFI



91 or Higher



99 / 5200 (133@5200)



201 / 4400 (148@4400)



12-55, 12-48*
5



960



1.4



Dry, Single Plate Ð Ð Ð
S51 A140E


3.538 2.810


1.960 1.549


1.250 1.000


0.945 0.706


0.731 Ð Ð Ð
3.153 2.296


Ð 0.945


3.944



Ventilated Disc



L.T. Drum



Drum



Tandem 8º + 9º
Tandem 8.5º + 8.5º*
3, 8º + 9º*4

Dual-P Valve



MacPherson Strut



MacPherson Strut



STD



STD



Rack and Pinion



17.4 : 1



Integral Type



*
1: Unladed Vehicle *4: Produced by TMMK
*2: With Moor Roof *5: Without Cold Area Specification Model
*3: Produced by TMC

CAMRY - MAJOR TECHNICAL SPECIFICATIONS
1st Gear km / h (mph) Angle of Approach degrees
Angle of Departure degrees
ItemArea
Body Type
Vehicle Grade
Model Code
OverallLength mm (in.)
Width mm (in.)
Height*
1mm (in.)
Wheel Base mm (in.)
TreadFront mm (in.)
Rear mm (in.)
Effective Head RoomFront mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.)
Front mm (in.)
Rear mm (in.) Effective Leg Room
Shoulder Room
Overhang
Min. Running Ground Clearance mm (in.)
Curb Weight
Gross Vehicle WeightFront kg (lb)
Rear kg (lb)
Total kg (lb)
Front kg (lb)
Rear kg (lb)
Total kg (lb)
Fuel Tank Capacity (US.gal., lmp.gal)
Luggage Compartment Capacity m
3 (cu.ft.)
Max. Speed km / h (mph)
Max. Cruising Speed km / h (mph)
Max. Permissible
Speed
Turning Diameter
(Outside Front)2nd Gear km / h (mph)
3rd Gear km / h (mph)
4th Gear km / h (mph)
Wall to Wall m (ft.)
Curb to Curb m (ft.)
Engine Type
Valve Mechanism
Bore x Stroke mm (in.)
Displacement cm
3 (cu.in.)
Compression Ratio
Carburetor Type
Research Octane No. RON
Max. Output (SAE-NET) kW / rpm (HP@rpm)
Max. Torque (SAE-NET) N
.m / rpm (lb-ft@rpm)
Battery Capacity (5HR) Voltage & Amp. hr.
Generator Output Watts
Starter Output kW
Clutch Type
Transaxle Type
Transmission Gear
Ratio
Differential Gear Ratio (Final)
Brake Type
Parking Brake Type
Brake Booster Type and Size in.
Proportioning Valve Type
Suspension Type
Stabilizer Bar
Steering Gear Type
Steering Gear Ratio (Overall)
Power Steering TypeIn First
In Second
In Third
In Fourth
In Fifth
In Reverse
Front
Rear
Front
Rear
Front
Rear
5
10
15
20
25
30
35
40
45
50
55
60
65
70
Major Dimensions & Vehicle Weights Performance Engine Engine
Chassis
Electrical
Canada
4-Door Sedan
CE LE
0 to 100 km / h sec.
0 to 400 m sec. Acceleration
Counter Gear RatioXLE
U.S.A.
6
MCV20L-AEPDKK MCV20L-AEPGKK SXV23L-AEPNCA
4790 (188.6)


1780 (70.1) 1785 (70.3) 1780 (70.1)
1420 (55.9)


2670 (105.1)


1545 (60.8)


1520 (59.8)


980 (38.6), 950 (37.4)*
2
980 (38.6)
940 (37.0), 914 (36.0)*2
940 (37.0)
1102 (43.4)


901 (35.5)


1427 (56.2)


1425 (56.1)


975 (38.4)


1145 (45.1)


135 (5.3)
130 (5.1)
16

16

16

16

860 (1896) 920 (2028) 860 (1896)
540 (1190) 545 (1202) 595 (1312)
1400 (3086) 1465 (3230) 1455 (3208)
1040 (2290)
970 (2140)
900 (1985)
950 (2095)
1940 (4275)
1920 (4235)
70 (18.5, 15.4)

135 (35.7, 29.2)*5, 43 (11.4, 9.5)*6
0.399 (14.1)
0.332 m3 *7, 8.921 ft3 *8
210 (130)
180 (112)
Ð
Ð
ÐÐÐ
ÐÐÐ
70 (43)
66 (41)
127 (79)
119 (74)
ÐÐÐ
ÐÐÐ
11.9 (39.0)


11.4 (37.4)


1MZ-FE
5S-FNE
24-Valve, DOHC
16-Valve, DOHC
87.5 x 83.0 (3.44 x 3.27)
87.0 x 91.0 (3.43 x 3.58)
2995 (182.7)
2164 (132.0)
10.5 : 1
11.0 : 1
SFI


91 or higher
130
143 / 5200 (192@5200)
88 / 5200 (118@5200)
281 / 4400 (207@4400)
178 / 2400 (131@2400)
12-55


960


1.4


ÐÐÐ
A541E
A140E
2.810
2.810
1.549
1.549
1.000
1.000
0.735
0.706
ÐÐÐ
2.296




0.945
3.933
4.176
Ventilated Disc


Solid Disc
L.T. Drum
Drum


Tandem 8.5º + 8.5º


Dual-P Valve


MacPherson Strut


MacPherson Strut


STD


STD


Rack and Pinion


17.4 : 1


Integral Type


*
1: Unladed Vehicle *5: Water Volume
*2: With Moon Roof *6: Equivalent Gasoline Capacity
*3: Produced by TMC *7: VDA
*4: Produced by TMMK *8: SAE Suitcase

The 5S±FE engine is an in±line, 4±cylinder engine with the cylinders numbered 1±2±3±4
from the front. The crankshaft is supported by five bearings inside the crankcase. These bearings
are made of aluminum alloy.
The crankshaft is integrated with eight weights for balance. Oil holes are placed in the center of
the crankshaft to supply oil to the connecting rods, bearing, pistons and other components.
The firing order is 1±3±4±2. The cylinder head is made of aluminum alloy, with a cross flow
type intake and exhaust layout and with pent±roof type combustion chambers. The spark plugs
are located in the center of the combustion chambers.
The intake manifold has four independent long ports and utilizes the inertial supercharging effect
to improve engine torque at low and medium speeds.
Exhaust and intake valves are equipped with irregular pitch springs made of special valve spring
carbon steel which are capable of functioning no matter what the engine speed.
The intake camshaft is driven by a timing belt, and a gear on the intake camshaft engages with
a gear on the exhaust camshaft to drive it. The cam journal is supported at five places between
the valve lifters of each cylinder and on the front end of the cylinder head. Lubrication of the cam
journals and gears is accomplished by oil being supplied through the oiler port in the center of the
camshaft.
Adjustment of the valve clearance is done by means of an outer shim type system, in which valve
adjusting shims are located above the valve lifters. This permits replacement of the shims without
removal of the camshafts.
Pistons are made of high temperature±resistant aluminum alloy, and a depression is built into
the piston head to prevent interference with the valves.
Piston pins are the full±floating type, with the pins fastened to neither the piston boss nor the
connecting rods. Instead, snap rings are fitted on both ends of the pins, preventing the pins from
falling out.
The No.1 compression ring is made of steel and the No.2 compression ring is made of cast iron.
The oil ring is made of a combination of steel and stainless steel. The outer diameter of each
piston ring is slightly larger than the diameter of the piston and the flexibility of the rings allows
them to hug the cylinder walls when they are mounted on the piston. Compression rings No.1 and
No.2 work to prevent gas leakage from the cylinder and the oil ring works to scrape oil off the
cylinder walls to prevent it from entering the combustion chambers.
The cylinder block is made of cast iron. It has four cylinders which are approximately twice the
length of the piston stroke. The top of each cylinder is closed off by the cylinder head and the
lower end of the cylinders becomes the crankcase, in which the crankshaft is installed. In
addition, the cylinder block contains a water jacket, through which coolant is pumped to cool the
cylinders.
The oil pan is bolted onto the bottom of the cylinder block. The oil pan is an oil reservoir made of
pressed sheet steel. A dividing plate is included 'inside the oil pan to keep sufficient oil in the
bottom of the pan even when the vehicle is tilted. This dividing plate also prevents the oil from
making waves when the vehicle is stopped suddenly and the oil shifts away from the oil pump
suction pipe.
The 5S±FE engine uses two balance shafts. The balance shafts are fitted in balance shaft
housings that are located at the bottom of the cylinder block. The No. 1 balance shaft is driven by
the drive gear of the crankshaft No.3 counterweight at twice the speed of the crankshaft. The No.
2 balance shaft is driven by the No±1 balance shaft at the same speed in the same direction as the
crankshaft. The balance shafts are designed to eliminate secondary inertia force from the engine,
thereby reducing the engine noise (booming noise).
± 5S±FE ENGINEENGINE MECHANICALEG1±3

(09248±05011) Valve Lifter Press
(09248±05021) Valve Lifter Stopper
09226±10010 Crankshaft Front & Rear Bearing
Replacer
09616±30011 Steering Worm Bearing Adjusting
Screw Wrench09224±74010 Engine Balancer Backlash
Adjusting Tool
09330±00021 Companion Flange Holding Tool09248±55020 Valve Clearance Adjust Tool Set
RECOMMENDED TOOLS
09816±30010 Oil Pressure Switch Socket09278±54012 Drive Shaft Holding Tool09249±63010 Torque Wrench Adaptor
09843±18020 Diagnosis Check Wire
09090±04010 Engine Sling Device
09200±00010 Engine Adjust KitCamshaft timing pulley
For suspension engineCrankshaft pulley
Oil pump pulley
Knock sensor
± 5S±FE ENGINEENGINE MECHANICALEG1±5

Plug for vacuum hose, fuel hose
etc.
Battery specific gravity gauge09256±00030 Hose Plug Set
09904±00010 Expander Set
Piston ring compressorEngine tune±up tester Connecting rod aligner
Precision straight edge
EQUIPMENT
Piston ring expander Compression gauge
Magnetic finger Cylinder gauge
Torque wrenchDye penetrant CO/HC meterCaliper gauge
Spring tester
ThermometerDial indicator
Steel squareMicrometer
Valve spring
Valve spring Plastigage
Soft brushHeater
± 5S±FE ENGINEENGINE MECHANICALEG1±6

(c) Install the gasket to the head cover.
(d) Install the head cover with the 4 grommets and nuts.
Uniformly tighten the nuts in several passes.
Torque: 23 N±m (230 kgf±cm. 17 ft±lbf)
HINT: Install the grommets so that their markings are
as shown in the illustration.
(e) Tighten the 2 wire harness clamp (No.2 timing belt
cover) mounting bolts.
(f) Connect the PCV hoses.
7. RECONNECT HIGH±TENSION CORDS TO SPARK
PLUGS(c) Install a new adjusting shim.
wPlace a new adjusting shim on the valve lifter.
wUsing SST (A), press down the valve lifter and
remove SST (B).
SST 09248±50020 (09248±05011, 09248±05021)
(d) Recheck the valve clearance.
6. REINSTALL CYLINDER HEAD COVER
(a) Remove any old packing (FIPG) material.
(b) Apply seal packing to the cylinder head as shown in
the illustration.
Seal pecking:
Part No.08826±00080 or equivalent
± 5S±FE ENGINEENGINE MECHANICALEG1±15

4. FURTHER CHECK IGNITION TIMING
Ignition timing:
0 ± 10
BTDC @ idle
(Transmission in neutral position)
HINT: The timing mark moves in a range between 0

and 10
. (c) Loosen the bolt (California) or 2 bolts (except Califor±
nia), and adjust by turning the distributor.
(d) Tighten the bolt (California) or 2 bolts (except Califor±
nia), and recheck the ignition timing.
Torque: 19 N±m (195 kgf±cm, 14 ft±lbf)
5. DISCONNECT TACHOMETER AND TIMING LIGHT
FROM ENGINE(e) Remove the SST.
SST 09843±18020
± 5S±FE ENGINEENGINE MECHANICALEG1±19

(e) If the cylinder compression in one or more cylinders is
low, pour a small amount of engine oil into the cylin±
der through the spark plug hole and repeat steps (a)
through
(c) for cylinders with low compression.
wIf adding oil helps the compression, chances are
that the piston rings and/or cylinder bore are
worn or damaged.
wIf pressure stays low, a valve may be sticking or
seating is improper, or there may be leakage past
the gasket.
6. REINSTALL SPARK PLUGS
Using a 16 mm plug wrench, install the spark plug.
Torque: 18 N±m (180 kgf±cm, 13 ft±lbf)
7. RECONNECT HIGH±TENSION CORDS TO SPARK
PLUGS
8. RECONNECT DISTRIBUTOR CONNECTOR(S)
± 5S±FE ENGINEENGINE MECHANICALEG1±24